@@ -44,6 +44,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
new file mode 100644
@@ -0,0 +1,621 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/delete-node/ &rmtfs_mem;
+
+/ {
+
+ aliases {
+ hsuart0 = &uart6;
+ };
+
+ reserved-memory {
+ /*
+ * The rmtfs memory region in downstream is 'dynamically allocated'
+ * but given the same address every time. Hard code it as this address is
+ * where the modem firmware expects it to be.
+ */
+ rmtfs_mem: memory@f5b01000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0 0xf5b01000 0 0x200000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ /*
+ * It seems like reserving the old rmtfs_mem region is also needed to prevent
+ * random crashes which are most likely modem related, more testing needed.
+ */
+ removed_region: memory@88f00000 {
+ no-map;
+ reg = <0 0x88f00000 0 0x200000>;
+ };
+
+ ramoops: ramoops@ac300000 {
+ compatible = "ramoops";
+ reg = <0 0xac300000 0 0x400000>;
+ record-size = <0x40000>;
+ console-size = <0x40000>;
+ ftrace-size = <0x40000>;
+ pmsg-size = <0x200000>;
+ devinfo-size = <0x1000>;
+ ecc-size = <16>;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ /*
+ * Apparently RPMh does not provide support for PM8998 S4 because it
+ * is always-on; model it as a fixed regulator.
+ */
+ vreg_s4a_1p8: pm8998-smps4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&vph_pwr>;
+ };
+
+ /*
+ * The touchscreen regulator seems to be controlled somehow by a gpio.
+ * Model it as a fixed regulator and keep it on. Without schematics we
+ * don't know how this is actually wired up...
+ */
+ ts_1p8_supply: ts-1p8-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "ts_1p8_supply";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 88 0>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ label = "Volume keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
+
+ vol-down {
+ label = "Volume down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ };
+
+ vol-up {
+ label = "Volume up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ };
+ };
+};
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-s11-supply = <&vph_pwr>;
+ vdd-s12-supply = <&vph_pwr>;
+ vdd-s13-supply = <&vph_pwr>;
+ vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+ vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+ vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+ vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+ vdd-l6-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+ vdd-l9-supply = <&vreg_bob>;
+ vdd-l10-l23-l25-supply = <&vreg_bob>;
+ vdd-l13-l19-l21-supply = <&vreg_bob>;
+ vdd-l16-l28-supply = <&vreg_bob>;
+ vdd-l18-l22-supply = <&vreg_bob>;
+ vdd-l20-l24-supply = <&vreg_bob>;
+ vdd-l26-supply = <&vreg_s3a_1p35>;
+ vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: smps3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_s5a_2p04: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_s7a_1p025: smps7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+
+ vdda_mipi_dsi0_pll:
+ vdda_qlink_lv:
+ vdda_ufs1_core:
+ vdda_usb1_ss_core:
+ vreg_l1a_0p875: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2a_1p2: ldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l5a_0p8: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_qusb_hs0_1p8:
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14a_1p88: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l17a_1p3: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l20a_2p95: ldo20 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vdda_qusb_hs0_3p1:
+ vreg_l24a_3p075: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l25a_3p3: ldo25 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ vdda_mipi_dsi0_1p2:
+ vdda_ufs1_1p2:
+ vreg_l26a_1p2: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l28a_3p0: ldo28 {
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmi8998-rpmh-regulators {
+ compatible = "qcom,pmi8998-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-allow-bypass;
+ };
+ };
+
+ pm8005-rpmh-regulators {
+ compatible = "qcom,pm8005-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s3c_0p6: smps3 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ };
+ };
+};
+
+&adsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
+};
+
+&cdsp_pas {
+ status = "okay";
+ firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
+};
+
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /*
+ * Both devices use different panels but all other properties
+ * are common. Compatible line is declared in device dts.
+ */
+ display_panel: panel@0 {
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ vddio-supply = <&vreg_l14a_1p88>;
+
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+};
+
+&dsi0_out {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+ status = "okay";
+ vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <GCC_LPASS_Q6_AXI_CLK>,
+ <GCC_LPASS_SWAY_CLK>;
+};
+
+&gpu {
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
+ };
+};
+
+&i2c12 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ synaptics-rmi4-i2c@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_default_pins>;
+
+ vdd-supply = <&vreg_l28a_3p0>;
+ vio-supply = <&ts_1p8_supply>;
+
+ syna,reset-delay-ms = <200>;
+ syna,startup-delay-ms = <200>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ touchscreen-x-mm = <68>;
+ touchscreen-y-mm = <144>;
+ syna,sensor-type = <1>;
+ syna,rezero-wait-ms = <200>;
+ };
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
+/* Modem/wifi*/
+&mss_pil {
+ status = "okay";
+ firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
+};
+
+&pm8998_gpio {
+ volume_down_gpio: pm8998_gpio5 {
+ pinconf {
+ pins = "gpio5";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <0>;
+ };
+ };
+
+ volume_up_gpio: pm8998_gpio6 {
+ pinconf {
+ pins = "gpio6";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <0>;
+ };
+ };
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qup_i2c12_default {
+ mux {
+ pins = "gpio49", "gpio50";
+ function = "qup12";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_i2c10_default {
+ pinconf {
+ pins = "gpio55", "gpio56";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_uart9_default {
+ pinconf-tx {
+ pins = "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+// Prevent garbage data on bluetooth UART lines
+&qup_uart6_default {
+ pinmux {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
+ };
+
+ cts {
+ pins = "gpio45";
+ bias-pull-down;
+ };
+
+ rts-tx {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
+
+&uart6 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ /*
+ * This path is relative to the qca/
+ * subdir under lib/firmware.
+ */
+ firmware-name = "oneplus6/crnv21.bin";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vdda_ufs1_core>;
+ vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+ status = "okay";
+
+ /*
+ * disable USB3 clock requirement as the device only supports
+ * USB2.
+ */
+ qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+ /*
+ * We don't have the capability to switch modes yet.
+ */
+ dr_mode = "peripheral";
+
+ /* fastest mode for USB 2 */
+ maximum-speed = "high-speed";
+
+ /* Remove USB3 phy as it's unused on this device. */
+ phys = <&usb_1_hsphy>;
+ phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vdda_usb1_ss_core>;
+ vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+ vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ tri_state_key_default: tri_state_key_default {
+ mux {
+ pins = "gpio40", "gpio42", "gpio26";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ts_default_pins: ts-int {
+ mux {
+ pins = "gpio99", "gpio125";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ panel_reset_pins: panel-reset {
+ mux {
+ pins = "gpio6", "gpio25", "gpio26";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable = <0>;
+ };
+ };
+
+ panel_te_pin: panel-te {
+ mux {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
+ };
+
+ panel_esd_pin: panel-esd {
+ mux {
+ pins = "gpio30";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-enable;
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+ qcom,snoc-host-cap-8bit-quirk;
+};
\ No newline at end of file
new file mode 100644
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6 (enchilada) device tree.
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "sdm845-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 6";
+ compatible = "oneplus,enchilada", "qcom,sdm845";
+};
+
+&display_panel {
+ status = "okay";
+
+ compatible = "samsung,sofef00";
+};
new file mode 100644
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 OnePlus 6T (fajita) device tree.
+ *
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "sdm845-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 6T";
+ compatible = "oneplus,fajita", "qcom,sdm845";
+};
+
+&display_panel {
+ status = "okay";
+
+ compatible = "samsung,s6e3fc2x01";
+};
+
+&rmi4_f12 {
+ touchscreen-y-mm = <148>;
+};
Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based on the sdm845-mtp DT with the following functionality: * Touch * Display * GPU * Wlan and Bluetooth * USB peripheral mode * Remoteproc Signed-off-by: Caleb Connolly <caleb@connolly.tech> --- Changes since v1 * Remove unused pinctrl nodes * Properly model touchscreen vio supply GPIO * Improve comments * Remove bq27541 battery as it doesn't work Changes since v2 * Specify clock frequency of touchscreen i2c * Remove tri-state-key nodes until a better solution can be found * Cleaned up pinctrl nodes * Remove unused regulators * Improve formatting * Address Bjorn's comments * Remove unused regulators --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 621 ++++++++++++++++++ .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 + .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 23 + 4 files changed, 665 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts