new file mode 100644
@@ -0,0 +1,93 @@
+What: /sys/class/udc/<udc>/a_alt_hnp_support
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates if an OTG A-Host supports HNP at an alternate port.
+Users:
+
+What: /sys/class/udc/<udc>/a_hnp_support
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates if an OTG A-Host supports HNP at this port.
+Users:
+
+What: /sys/class/udc/<udc>/b_hnp_enable
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates if an OTG A-Host enabled HNP support.
+Users:
+
+What: /sys/class/udc/<udc>/current_speed
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates the current negotiated speed at this port.
+Users:
+
+What: /sys/class/udc/<udc>/is_a_peripheral
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates that this port is the default Host on an OTG session
+ but HNP was used to switch roles.
+Users:
+
+What: /sys/class/udc/<udc>/is_otg
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates that this port support OTG.
+Users:
+
+What: /sys/class/udc/<udc>/maximum_speed
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates the maximum USB speed supported by this port.
+Users:
+
+What: /sys/class/udc/<udc>/maximum_speed
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates the maximum USB speed supported by this port.
+Users:
+
+What: /sys/class/udc/<udc>/soft_connect
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Allows users to disconnect data pullup resistors thus causing a
+ logical disconnection from the USB Host.
+Users:
+
+What: /sys/class/udc/<udc>/srp
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Allows users to manually start Session Request Protocol.
+Users:
+
+What: /sys/class/udc/<udc>/state
+Date: June 2011
+KernelVersion: 3.1
+Contact: Felipe Balbi <balbi@kernel.org>
+Description:
+ Indicates current state of the USB Device Controller. Valid
+ states are: 'not-attached', 'attached', 'powered',
+ 'reconnecting', 'unauthenticated', 'default', 'addressed',
+ 'configured', and 'suspended'; however not all USB Device
+ Controllers support reporting all states.
+Users:
I noticed that this has been missing for quite some time so I decided it was about time to document it. Signed-off-by: Felipe Balbi <balbi@ti.com> --- Documentation/ABI/stable/sysfs-class-udc | 93 ++++++++++++++++++++++++++++++++ 1 file changed, 93 insertions(+) create mode 100644 Documentation/ABI/stable/sysfs-class-udc