@@ -67,8 +67,7 @@ static void enetc_update_tx_ring_tail(struct enetc_bdr *tx_ring)
enetc_wr_reg_hot(tx_ring->tpir, tx_ring->next_to_use);
}
-static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb,
- int active_offloads)
+static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb)
{
struct enetc_tx_swbd *tx_swbd;
skb_frag_t *frag;
@@ -101,7 +100,7 @@ static int enetc_map_tx_buffs(struct enetc_bdr *tx_ring, struct sk_buff *skb,
count++;
do_vlan = skb_vlan_tag_present(skb);
- do_tstamp = (active_offloads & ENETC_F_TX_TSTAMP) &&
+ do_tstamp = (skb->cb[0] & ENETC_F_TX_TSTAMP) &&
(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP);
tx_swbd->do_tstamp = do_tstamp;
tx_swbd->check_wb = tx_swbd->do_tstamp;
@@ -221,6 +220,9 @@ netdev_tx_t enetc_xmit(struct sk_buff *skb, struct net_device *ndev)
struct enetc_bdr *tx_ring;
int count;
+ /* cb[0] used for TX timestamp type */
+ skb->cb[0] = priv->active_offloads & ENETC_F_TX_TSTAMP_MASK;
+
tx_ring = priv->tx_ring[skb->queue_mapping];
if (unlikely(skb_shinfo(skb)->nr_frags > ENETC_MAX_SKB_FRAGS))
@@ -234,7 +236,7 @@ netdev_tx_t enetc_xmit(struct sk_buff *skb, struct net_device *ndev)
}
enetc_lock_mdio();
- count = enetc_map_tx_buffs(tx_ring, skb, priv->active_offloads);
+ count = enetc_map_tx_buffs(tx_ring, skb);
enetc_unlock_mdio();
if (unlikely(!count))
@@ -271,12 +271,15 @@ struct psfp_cap {
u32 max_psfp_meter;
};
+#define ENETC_F_TX_TSTAMP_MASK 0xff
/* TODO: more hardware offloads */
enum enetc_active_offloads {
- ENETC_F_RX_TSTAMP = BIT(0),
- ENETC_F_TX_TSTAMP = BIT(1),
- ENETC_F_QBV = BIT(2),
- ENETC_F_QCI = BIT(3),
+ /* 8 bits reserved for TX timestamp types (hwtstamp_tx_types) */
+ ENETC_F_TX_TSTAMP = BIT(0),
+
+ ENETC_F_RX_TSTAMP = BIT(8),
+ ENETC_F_QBV = BIT(9),
+ ENETC_F_QCI = BIT(10),
};
/* interrupt coalescing modes */
Mark TX timestamp type per skb on skb->cb[0], instead of global variable for all skbs. This is a preparation for one step timestamp support. For one-step timestamping enablement, there will be both one-step and two-step PTP messages to transfer. And a skb queue is needed for one-step PTP messages making sure start to send current message only after the last one completed on hardware. (ENETC single-step register has to be dynamically configured per message.) So, marking TX timestamp type per skb is required. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> --- Changes for v2: - Rebased. Changes for v3: - None. --- drivers/net/ethernet/freescale/enetc/enetc.c | 10 ++++++---- drivers/net/ethernet/freescale/enetc/enetc.h | 11 +++++++---- 2 files changed, 13 insertions(+), 8 deletions(-)