diff mbox series

arm64: dts: qcom: add initial device-tree for Microsoft Surface Duo

Message ID 20210510120547.1315536-1-balbi@kernel.org
State New
Headers show
Series arm64: dts: qcom: add initial device-tree for Microsoft Surface Duo | expand

Commit Message

Felipe Balbi May 10, 2021, 12:05 p.m. UTC
From: Felipe Balbi <felipe.balbi@microsoft.com>

Microsoft Surface Duo is based on SM8150 chipset. This new Device Tree
is a copy of sm8150-mtp with a the addition of the volume up key and
relevant i2c nodes.

Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
---

 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/sm8150-microsoft-surface-duo.dts | 545 ++++++++++++++++++
 2 files changed, 546 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts

Comments

Konrad Dybcio May 18, 2021, 8:57 p.m. UTC | #1
Hi!


> +/ {
> +	model = "Microsoft Surface Duo";
> +	compatible = "microsoft,surface-duo", "qcom,sm8150-mtp";
> +
Please remove the -mtp compatible, as the phone is not 1:1 compatible with the MTP design and replace it with the platform-generic "qcom,sm8150" (otherwise things like CPUFreq won't work!).


> +
> +	aliases {
> +		serial0 = &uart2;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +

Is the serial port exposed and enabled on production hardware?


> +
> +	bq27742@55 {
> +		compatible = "ti,bq27742";
> +		reg = <0x55>;
> +	};
> +
> +	da7280@4a {
> +		compatible = "dlg,da7280";
> +		reg = <0x4a>;
> +		interrupts-extended = <&tlmm 42 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "da7280_default";
> +		pinctrl-0 = <&da7280_intr_default>;
> +
> +		dlg,actuator-type = "LRA";
> +		dlg,dlg,const-op-mode = <1>;
> +		dlg,dlg,periodic-op-mode = <1>;
> +		dlg,nom-microvolt = <2000000>;
> +		dlg,abs-max-microvolt = <2000000>;
> +		dlg,imax-microamp = <129000>;
> +		dlg,resonant-freq-hz = <180>;
> +		dlg,impd-micro-ohms = <14300000>;
> +		dlg,freq-track-enable;
> +		dlg,bemf-sens-enable;
> +		dlg,mem-array = <
> +		  0x06 0x08 0x10 0x11 0x12 0x13 0x14 0x15 0x1c 0x2a
> +		  0x33 0x3c 0x42 0x4b 0x4c 0x4e 0x17 0x19 0x27 0x29
> +		  0x17 0x19 0x03 0x84 0x5e 0x04 0x08 0x84 0x5d 0x01
> +		  0x84 0x5e 0x02 0x00 0xa4 0x5d 0x03 0x84 0x5e 0x06
> +		  0x08 0x84 0x5d 0x05 0x84 0x5d 0x06 0x84 0x5e 0x08
> +		  0x84 0x5e 0x05 0x8c 0x5e 0x24 0x84 0x5f 0x10 0x84
> +		  0x5e 0x05 0x84 0x5e 0x08 0x84 0x5f 0x01 0x8c 0x5e
> +		  0x04 0x84 0x5e 0x08 0x84 0x5f 0x11 0x19 0x88 0x00
> +		  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> +		  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> +		>;
> +	};
> +
> +	/* SMB1381 @ 0x44 */
> +	/* MAX34417 @ 0x1c */
> +};

Please add generic labels to these peripherals, such as "vibrator: " or so.


> +&i2c17 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	bq27742@55 {
> +		compatible = "ti,bq27742";
> +		reg = <0x55>;
> +	};
> +};

Are there actually two of these TI ICs, presumably for the dual-batteries? If that's the case, could you add a comment specifying which one is in charge (pun intended) of which cell?


Aside from that, it generally looks good :)


Konrad
Bjorn Andersson May 25, 2021, 5:32 p.m. UTC | #2
On Tue 11 May 03:07 CDT 2021, Felipe Balbi wrote:
> Bjorn Andersson <bjorn.andersson@linaro.org> writes:
> >> diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
[..]
> >> +&remoteproc_adsp {
> >> +	status = "okay";
> >> +	firmware-name = "qcom/sm8150/adsp.mdt";
> >
> > For platforms where we have a Dragonboard or similar we push the
> > test-signed firmware to qcom/<platform>/. I presume that the Duo
> > wouldn't run on the test-signed firmware.
> >
> > So I think it's better to make this qcom/sm8150/ms-duo/adsp.mdt...from
> > the start.
> 
> ms-duo would look odd. How about qcom/sm8150/microsoft/adsp.mdt?
> 

Sounds good to me.

I do prefer using the non-split firmware package though (i.e. .mbn), if
you don't have it you can repack the .mdt + .bNN files using

https://github.com/andersson/pil-squasher

Regards,
Bjorn
Felipe Balbi May 28, 2021, 9:57 a.m. UTC | #3
Bjorn Andersson <bjorn.andersson@linaro.org> writes:

> On Tue 11 May 03:07 CDT 2021, Felipe Balbi wrote:
>> Bjorn Andersson <bjorn.andersson@linaro.org> writes:
>> >> diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
> [..]
>> >> +&remoteproc_adsp {
>> >> +	status = "okay";
>> >> +	firmware-name = "qcom/sm8150/adsp.mdt";
>> >
>> > For platforms where we have a Dragonboard or similar we push the
>> > test-signed firmware to qcom/<platform>/. I presume that the Duo
>> > wouldn't run on the test-signed firmware.
>> >
>> > So I think it's better to make this qcom/sm8150/ms-duo/adsp.mdt...from
>> > the start.
>> 
>> ms-duo would look odd. How about qcom/sm8150/microsoft/adsp.mdt?
>> 
>
> Sounds good to me.
>
> I do prefer using the non-split firmware package though (i.e. .mbn), if
> you don't have it you can repack the .mdt + .bNN files using
>
> https://github.com/andersson/pil-squasher

Cool, I'll check if we have the non-split version and rename the FW
files.
Felipe Balbi May 28, 2021, 10 a.m. UTC | #4
Hi,

(please break lines at 80-columns)

Konrad Dybcio <konrad.dybcio@somainline.org> writes:
>> +	model = "Microsoft Surface Duo";

>> +	compatible = "microsoft,surface-duo", "qcom,sm8150-mtp";

>> +

> Please remove the -mtp compatible, as the phone is not 1:1 compatible

> with the MTP design and replace it with the platform-generic

> "qcom,sm8150" (otherwise things like CPUFreq won't work!).


will do

>> +	aliases {

>> +		serial0 = &uart2;

>> +	};

>> +

>> +	chosen {

>> +		stdout-path = "serial0:115200n8";

>> +	};

>> +

>

> Is the serial port exposed and enabled on production hardware?


nope, but we also use the same DTS for devBoards.

>> +	bq27742@55 {

>> +		compatible = "ti,bq27742";

>> +		reg = <0x55>;

>> +	};

>> +

>> +	da7280@4a {

>> +		compatible = "dlg,da7280";

>> +		reg = <0x4a>;

>> +		interrupts-extended = <&tlmm 42 IRQ_TYPE_LEVEL_LOW>;

>> +		pinctrl-names = "da7280_default";

>> +		pinctrl-0 = <&da7280_intr_default>;

>> +

>> +		dlg,actuator-type = "LRA";

>> +		dlg,dlg,const-op-mode = <1>;

>> +		dlg,dlg,periodic-op-mode = <1>;

>> +		dlg,nom-microvolt = <2000000>;

>> +		dlg,abs-max-microvolt = <2000000>;

>> +		dlg,imax-microamp = <129000>;

>> +		dlg,resonant-freq-hz = <180>;

>> +		dlg,impd-micro-ohms = <14300000>;

>> +		dlg,freq-track-enable;

>> +		dlg,bemf-sens-enable;

>> +		dlg,mem-array = <

>> +		  0x06 0x08 0x10 0x11 0x12 0x13 0x14 0x15 0x1c 0x2a

>> +		  0x33 0x3c 0x42 0x4b 0x4c 0x4e 0x17 0x19 0x27 0x29

>> +		  0x17 0x19 0x03 0x84 0x5e 0x04 0x08 0x84 0x5d 0x01

>> +		  0x84 0x5e 0x02 0x00 0xa4 0x5d 0x03 0x84 0x5e 0x06

>> +		  0x08 0x84 0x5d 0x05 0x84 0x5d 0x06 0x84 0x5e 0x08

>> +		  0x84 0x5e 0x05 0x8c 0x5e 0x24 0x84 0x5f 0x10 0x84

>> +		  0x5e 0x05 0x84 0x5e 0x08 0x84 0x5f 0x01 0x8c 0x5e

>> +		  0x04 0x84 0x5e 0x08 0x84 0x5f 0x11 0x19 0x88 0x00

>> +		  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00

>> +		  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00

>> +		>;

>> +	};

>> +

>> +	/* SMB1381 @ 0x44 */

>> +	/* MAX34417 @ 0x1c */

>> +};

>

> Please add generic labels to these peripherals, such as "vibrator: " or so.


why? They haven't been added yet, they don't even have drivers
available. What extra information will a comment bring?

>> +&i2c17 {

>> +	status = "okay";

>> +	clock-frequency = <400000>;

>> +

>> +	bq27742@55 {

>> +		compatible = "ti,bq27742";

>> +		reg = <0x55>;

>> +	};

>> +};

>

> Are there actually two of these TI ICs, presumably for the


yes

> dual-batteries? If that's the case, could you add a comment specifying

> which one is in charge (pun intended) of which cell?


that's detected, and reported, by the HW itself. Also, what's the point
if SW isn't really doing anything with the batteries other than checking
charge level and such?

-- 
balbi
Felipe Balbi May 28, 2021, 12:03 p.m. UTC | #5
Felipe Balbi <balbi@kernel.org> writes:

> Bjorn Andersson <bjorn.andersson@linaro.org> writes:
>
>> On Tue 11 May 03:07 CDT 2021, Felipe Balbi wrote:
>>> Bjorn Andersson <bjorn.andersson@linaro.org> writes:
>>> >> diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
>> [..]
>>> >> +&remoteproc_adsp {
>>> >> +	status = "okay";
>>> >> +	firmware-name = "qcom/sm8150/adsp.mdt";
>>> >
>>> > For platforms where we have a Dragonboard or similar we push the
>>> > test-signed firmware to qcom/<platform>/. I presume that the Duo
>>> > wouldn't run on the test-signed firmware.
>>> >
>>> > So I think it's better to make this qcom/sm8150/ms-duo/adsp.mdt...from
>>> > the start.
>>> 
>>> ms-duo would look odd. How about qcom/sm8150/microsoft/adsp.mdt?
>>> 
>>
>> Sounds good to me.
>>
>> I do prefer using the non-split firmware package though (i.e. .mbn), if
>> you don't have it you can repack the .mdt + .bNN files using
>>
>> https://github.com/andersson/pil-squasher
>
> Cool, I'll check if we have the non-split version and rename the FW
> files.

doesn't seem like pil-squasher works with our slpi image. Gives me a
0-byte image :-)

I would rather not touch the binaries if I can avoid it, though. Is this
a strong requirement to use mbn rather than mdt?
Bjorn Andersson May 29, 2021, 4:56 p.m. UTC | #6
On Fri 28 May 07:03 CDT 2021, Felipe Balbi wrote:

> Felipe Balbi <balbi@kernel.org> writes:
> 
> > Bjorn Andersson <bjorn.andersson@linaro.org> writes:
> >
> >> On Tue 11 May 03:07 CDT 2021, Felipe Balbi wrote:
> >>> Bjorn Andersson <bjorn.andersson@linaro.org> writes:
> >>> >> diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
> >> [..]
> >>> >> +&remoteproc_adsp {
> >>> >> +	status = "okay";
> >>> >> +	firmware-name = "qcom/sm8150/adsp.mdt";
> >>> >
> >>> > For platforms where we have a Dragonboard or similar we push the
> >>> > test-signed firmware to qcom/<platform>/. I presume that the Duo
> >>> > wouldn't run on the test-signed firmware.
> >>> >
> >>> > So I think it's better to make this qcom/sm8150/ms-duo/adsp.mdt...from
> >>> > the start.
> >>> 
> >>> ms-duo would look odd. How about qcom/sm8150/microsoft/adsp.mdt?
> >>> 
> >>
> >> Sounds good to me.
> >>
> >> I do prefer using the non-split firmware package though (i.e. .mbn), if
> >> you don't have it you can repack the .mdt + .bNN files using
> >>
> >> https://github.com/andersson/pil-squasher
> >
> > Cool, I'll check if we have the non-split version and rename the FW
> > files.
> 
> doesn't seem like pil-squasher works with our slpi image. Gives me a
> 0-byte image :-)
> 

If your files are available somewhere I'd be happy to take a look, if
not patches are definitely welcome :)

> I would rather not touch the binaries if I can avoid it, though. Is this
> a strong requirement to use mbn rather than mdt?
> 

I've had numerous problems with things such as people upgrading N-1
files and having issues with the signature check just indicating that
"something" is wrong. Squashing the files avoid these kind of problems.

But it's not a requirement!

Regards,
Bjorn
Felipe Balbi June 3, 2021, 10:19 a.m. UTC | #7
Bjorn Andersson <bjorn.andersson@linaro.org> writes:

> On Fri 28 May 07:03 CDT 2021, Felipe Balbi wrote:
>
>> Felipe Balbi <balbi@kernel.org> writes:
>> 
>> > Bjorn Andersson <bjorn.andersson@linaro.org> writes:
>> >
>> >> On Tue 11 May 03:07 CDT 2021, Felipe Balbi wrote:
>> >>> Bjorn Andersson <bjorn.andersson@linaro.org> writes:
>> >>> >> diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
>> >> [..]
>> >>> >> +&remoteproc_adsp {
>> >>> >> +	status = "okay";
>> >>> >> +	firmware-name = "qcom/sm8150/adsp.mdt";
>> >>> >
>> >>> > For platforms where we have a Dragonboard or similar we push the
>> >>> > test-signed firmware to qcom/<platform>/. I presume that the Duo
>> >>> > wouldn't run on the test-signed firmware.
>> >>> >
>> >>> > So I think it's better to make this qcom/sm8150/ms-duo/adsp.mdt...from
>> >>> > the start.
>> >>> 
>> >>> ms-duo would look odd. How about qcom/sm8150/microsoft/adsp.mdt?
>> >>> 
>> >>
>> >> Sounds good to me.
>> >>
>> >> I do prefer using the non-split firmware package though (i.e. .mbn), if
>> >> you don't have it you can repack the .mdt + .bNN files using
>> >>
>> >> https://github.com/andersson/pil-squasher
>> >
>> > Cool, I'll check if we have the non-split version and rename the FW
>> > files.
>> 
>> doesn't seem like pil-squasher works with our slpi image. Gives me a
>> 0-byte image :-)
>> 
>
> If your files are available somewhere I'd be happy to take a look, if
> not patches are definitely welcome :)
>
>> I would rather not touch the binaries if I can avoid it, though. Is this
>> a strong requirement to use mbn rather than mdt?
>> 
>
> I've had numerous problems with things such as people upgrading N-1
> files and having issues with the signature check just indicating that
> "something" is wrong. Squashing the files avoid these kind of problems.
>
> But it's not a requirement!

fair enough, I'll send a v2 as soon as I test everything on top of -rc4.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 456502aeee49..9cfd409207cc 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -70,6 +70,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-fajita.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-beryllium.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-microsoft-surface-duo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
new file mode 100644
index 000000000000..f53d4b3dd482
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
@@ -0,0 +1,545 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (C) 2021, Microsoft Corporation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "sm8150.dtsi"
+#include "pm8150.dtsi"
+#include "pm8150b.dtsi"
+#include "pm8150l.dtsi"
+
+/ {
+	model = "Microsoft Surface Duo";
+	compatible = "microsoft,surface-duo", "qcom,sm8150-mtp";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	/*
+	 * Apparently RPMh does not provide support for PM8150 S4 because it
+	 * is always-on; model it as a fixed regulator.
+	 */
+	vreg_s4a_1p8: pm8150-s4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		vol_up {
+			label = "Volume Up";
+			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+};
+
+&tlmm {
+	da7280_intr_default: da7280-intr-default {
+		pins = "gpio42";
+		function = "gpio";
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	bq27742@55 {
+		compatible = "ti,bq27742";
+		reg = <0x55>;
+	};
+
+	da7280@4a {
+		compatible = "dlg,da7280";
+		reg = <0x4a>;
+		interrupts-extended = <&tlmm 42 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "da7280_default";
+		pinctrl-0 = <&da7280_intr_default>;
+
+		dlg,actuator-type = "LRA";
+		dlg,dlg,const-op-mode = <1>;
+		dlg,dlg,periodic-op-mode = <1>;
+		dlg,nom-microvolt = <2000000>;
+		dlg,abs-max-microvolt = <2000000>;
+		dlg,imax-microamp = <129000>;
+		dlg,resonant-freq-hz = <180>;
+		dlg,impd-micro-ohms = <14300000>;
+		dlg,freq-track-enable;
+		dlg,bemf-sens-enable;
+		dlg,mem-array = <
+		  0x06 0x08 0x10 0x11 0x12 0x13 0x14 0x15 0x1c 0x2a
+		  0x33 0x3c 0x42 0x4b 0x4c 0x4e 0x17 0x19 0x27 0x29
+		  0x17 0x19 0x03 0x84 0x5e 0x04 0x08 0x84 0x5d 0x01
+		  0x84 0x5e 0x02 0x00 0xa4 0x5d 0x03 0x84 0x5e 0x06
+		  0x08 0x84 0x5d 0x05 0x84 0x5d 0x06 0x84 0x5e 0x08
+		  0x84 0x5e 0x05 0x8c 0x5e 0x24 0x84 0x5f 0x10 0x84
+		  0x5e 0x05 0x84 0x5e 0x08 0x84 0x5f 0x01 0x8c 0x5e
+		  0x04 0x84 0x5e 0x08 0x84 0x5f 0x11 0x19 0x88 0x00
+		  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
+		  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
+		>;
+	};
+
+	/* SMB1381 @ 0x44 */
+	/* MAX34417 @ 0x1c */
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* SMB1355 @ 0x0c */
+	/* SMB1390 @ 0x10 */
+};
+
+&qupv3_id_2 {
+	status = "okay";
+};
+
+&i2c17 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	bq27742@55 {
+		compatible = "ti,bq27742";
+		reg = <0x55>;
+	};
+};
+
+&i2c19 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* MAX34417 @ 0x12 */
+	/* MAX34417 @ 0x1a */
+	/* MAX34417 @ 0x1e */
+};
+
+&apps_rsc {
+	pm8150-rpmh-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+
+		vdd-l1-l8-l11-supply = <&vreg_s6a_0p9>;
+		vdd-l2-l10-supply = <&vreg_bob>;
+		vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p9>;
+		vdd-l6-l9-supply = <&vreg_s8c_1p3>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
+		vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+		vreg_s5a_2p0: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2000000>;
+		};
+
+		vreg_s6a_0p9: smps6 {
+			regulator-min-microvolt = <920000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vdda_wcss_pll:
+		vreg_l1a_0p75: ldo1 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_pdphy:
+		vdda_usb_hs_3p1:
+		vreg_l2a_3p1: ldo2 {
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3a_0p8: ldo3 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <932000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_usb_hs_core:
+		vdda_csi_0_0p9:
+		vdda_csi_1_0p9:
+		vdda_csi_2_0p9:
+		vdda_csi_3_0p9:
+		vdda_dsi_0_0p9:
+		vdda_dsi_1_0p9:
+		vdda_dsi_0_pll_0p9:
+		vdda_dsi_1_pll_0p9:
+		vdda_pcie_1ln_core:
+		vdda_pcie_2ln_core:
+		vdda_pll_hv_cc_ebi01:
+		vdda_pll_hv_cc_ebi23:
+		vdda_qrefs_0p875_5:
+		vdda_sp_sensor:
+		vdda_ufs_2ln_core_1:
+		vdda_ufs_2ln_core_2:
+		vdda_usb_ss_dp_core_1:
+		vdda_usb_ss_dp_core_2:
+		vdda_qlink_lv:
+		vdda_qlink_lv_ck:
+		vreg_l5a_0p875: ldo5 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a_1p2: ldo6 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_10:
+		vreg_l9a_1p2: ldo9 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_2p5: ldo10 {
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_0p8: ldo11 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_qfprom:
+		vdd_qfprom_sp:
+		vdda_apc_cs_1p8:
+		vdda_gfx_cs_1p8:
+		vdda_usb_hs_1p8:
+		vdda_qrefs_vref_1p8:
+		vddpx_10_a:
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p7: ldo13 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p7: ldo15 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_3p0: ldo17 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8150l-rpmh-regulators {
+		compatible = "qcom,pm8150l-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+
+		vdd-l1-l8-supply = <&vreg_s4a_1p8>;
+		vdd-l2-l3-supply = <&vreg_s8c_1p3>;
+		vdd-l4-l5-l6-supply = <&vreg_bob>;
+		vdd-l7-l11-supply = <&vreg_bob>;
+		vdd-l9-l10-supply = <&vreg_bob>;
+
+		vdd-bob-supply = <&vph_pwr>;
+		vdd-flash-supply = <&vreg_bob>;
+		vdd-rgb-supply = <&vreg_bob>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <4000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+
+		vreg_s8c_1p3: smps8 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_wcss_adcdac_1:
+		vdda_wcss_adcdac_22:
+		vreg_l2c_1p3: ldo2 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_hv_ebi0:
+		vdda_hv_ebi1:
+		vdda_hv_ebi2:
+		vdda_hv_ebi3:
+		vdda_hv_refgen0:
+		vdda_qlink_hv_ck:
+		vreg_l3c_1p2: ldo3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_5:
+		vreg_l4c_1p8: ldo4 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_6:
+		vreg_l5c_1p8: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_2:
+		vreg_l6c_2p9: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p9: ldo9 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c_3p3: ldo10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c_3p3: ldo11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8009-rpmh-regulators {
+		compatible = "qcom,pm8009-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vreg_bob>;
+
+		vdd-l2-supply = <&vreg_s8c_1p3>;
+		vdd-l5-l6-supply = <&vreg_bob>;
+
+		vreg_l2f_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5f_2p85: ldo5 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6f_2p85: ldo6 {
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <2856000>;
+		};
+	};
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&pon {
+	pwrkey {
+		status = "okay";
+	};
+
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	firmware-name = "qcom/sm8150/adsp.mdt";
+};
+
+&remoteproc_cdsp {
+	status = "okay";
+	firmware-name = "qcom/sm8150/cdsp.mdt";
+};
+
+&remoteproc_mpss {
+	status = "okay";
+	firmware-name = "qcom/sm8150/modem.mdt";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+	firmware-name = "qcom/sm8150/slpi.mdt";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <126 4>;
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l10a_2p5>;
+	vcc-max-microamp = <750000>;
+	vccq-supply = <&vreg_l9a_1p2>;
+	vccq-max-microamp = <700000>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vccq2-max-microamp = <750000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
+	vdda-max-microamp = <90200>;
+	vdda-pll-supply = <&vreg_l3c_1p2>;
+	vdda-pll-max-microamp = <19000>;
+};
+
+&usb_1_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vdd_usb_hs_core>;
+	vdda33-supply = <&vdda_usb_hs_3p1>;
+	vdda18-supply = <&vdda_usb_hs_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l3c_1p2>;
+	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vdda_wcss_pll>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vdda_wcss_adcdac_1>;
+	vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
+};