[v1,1/1] pinctrl: Keep enum pin_config_param ordered by name (part 2)

Message ID 20210510194717.12255-1-andriy.shevchenko@linux.intel.com
State New
Headers show
Series
  • [v1,1/1] pinctrl: Keep enum pin_config_param ordered by name (part 2)
Related show

Commit Message

Andy Shevchenko May 10, 2021, 7:47 p.m.
It seems the ordering is by name. Keep it that way.
Here updating the entire list (there were two more options not in order).

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 include/linux/pinctrl/pinconf-generic.h | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

Comments

Linus Walleij May 19, 2021, 11:31 p.m. | #1
On Mon, May 10, 2021 at 9:47 PM Andy Shevchenko
<andriy.shevchenko@linux.intel.com> wrote:

> It seems the ordering is by name. Keep it that way.

> Here updating the entire list (there were two more options not in order).

>

> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>


Patch applied!

Yours,
Linus Walleij

Patch

diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index e18ab3d5908f..98ed5959ca9a 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -81,28 +81,28 @@  struct pinctrl_map;
  *	passed in the argument on a custom form, else just use argument 1
  *	to indicate low power mode, argument 0 turns low power mode off.
  * @PIN_CONFIG_MODE_PWM: this will configure the pin for PWM
+ * @PIN_CONFIG_OUTPUT: this will configure the pin as an output and drive a
+ * 	value on the line. Use argument 1 to indicate high level, argument 0 to
+ *	indicate low level. (Please see Documentation/driver-api/pinctl.rst,
+ *	section "GPIO mode pitfalls" for a discussion around this parameter.)
  * @PIN_CONFIG_OUTPUT_ENABLE: this will enable the pin's output mode
  * 	without driving a value there. For most platforms this reduces to
  * 	enable the output buffers and then let the pin controller current
  * 	configuration (eg. the currently selected mux function) drive values on
  * 	the line. Use argument 1 to enable output mode, argument 0 to disable
  * 	it.
- * @PIN_CONFIG_OUTPUT: this will configure the pin as an output and drive a
- * 	value on the line. Use argument 1 to indicate high level, argument 0 to
- *	indicate low level. (Please see Documentation/driver-api/pinctl.rst,
- *	section "GPIO mode pitfalls" for a discussion around this parameter.)
  * @PIN_CONFIG_PERSIST_STATE: retain pin state across sleep or controller reset
  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  *	supplies, the argument to this parameter (on a custom format) tells
  *	the driver which alternative power source to use.
- * @PIN_CONFIG_SLEEP_HARDWARE_STATE: indicate this is sleep related state.
- * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
- *	this parameter (on a custom format) tells the driver which alternative
- *	slew rate to use.
  * @PIN_CONFIG_SKEW_DELAY: if the pin has programmable skew rate (on inputs)
  *	or latch delay (on outputs) this parameter (in a custom format)
  *	specifies the clock skew or latch delay. It typically controls how
  *	many double inverters are put in front of the line.
+ * @PIN_CONFIG_SLEEP_HARDWARE_STATE: indicate this is sleep related state.
+ * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
+ *	this parameter (on a custom format) tells the driver which alternative
+ *	slew rate to use.
  * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
  *	you need to pass in custom configurations to the pin controller, use
  *	PIN_CONFIG_END+1 as the base offset.
@@ -127,13 +127,13 @@  enum pin_config_param {
 	PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 	PIN_CONFIG_MODE_LOW_POWER,
 	PIN_CONFIG_MODE_PWM,
-	PIN_CONFIG_OUTPUT_ENABLE,
 	PIN_CONFIG_OUTPUT,
+	PIN_CONFIG_OUTPUT_ENABLE,
 	PIN_CONFIG_PERSIST_STATE,
 	PIN_CONFIG_POWER_SOURCE,
+	PIN_CONFIG_SKEW_DELAY,
 	PIN_CONFIG_SLEEP_HARDWARE_STATE,
 	PIN_CONFIG_SLEW_RATE,
-	PIN_CONFIG_SKEW_DELAY,
 	PIN_CONFIG_END = 0x7F,
 	PIN_CONFIG_MAX = 0xFF,
 };