new file mode 100644
@@ -0,0 +1,148 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/cypress,cy8ctma340.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cypress CY8CTMA340 series touchscreen controller bindings
+
+description: The Cypress CY8CTMA340 series (also known as "CYTTSP" after
+ the marketing name Cypress TrueTouch Standard Product) touchscreens can
+ be connected to either I2C or SPI buses.
+
+maintainers:
+ - Javier Martinez Canillas <javier@dowhile0.org>
+ - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+ - $ref: touchscreen.yaml#
+
+properties:
+ $nodename:
+ pattern: "^touchscreen(@.*)?$"
+
+ compatible:
+ oneOf:
+ - const: cypress,cy8ctma340
+ - const: cypress,cy8ctst341
+ - const: cypress,cyttsp-spi
+ description: Legacy compatible for SPI connected CY8CTMA340
+ deprecated: true
+ - const: cypress,cyttsp-i2c
+ description: Legacy compatible for I2C connected CY8CTMA340
+ deprecated: true
+
+ reg:
+ description: I2C address when used on the I2C bus, or the SPI chip
+ select index when used on the SPI bus
+
+ clock-frequency:
+ description: I2C client clock frequency, defined for host when using
+ the device on the I2C bus
+ minimum: 0
+ maximum: 400000
+
+ spi-max-frequency:
+ description: SPI clock frequency, defined for host, defined when using
+ the device on the SPI bus. The throughput is maximum 2 Mbps so the
+ typical value is 2000000, if higher rates are used the total throughput
+ needs to be restricted to 2 Mbps.
+ minimum: 0
+ maximum: 6000000
+
+ interrupts:
+ description: Interrupt to host
+ maxItems: 1
+
+ vcpin-supply:
+ description: Analog power supply regulator on VCPIN pin
+
+ vdd-supply:
+ description: Digital power supply regulator on VDD pin
+
+ reset-gpios:
+ description: Reset line for the touchscreen, should be tagged
+ as GPIO_ACTIVE_LOW
+
+ bootloader-key:
+ description: the 8-byte bootloader key that is required to switch
+ the chip from bootloader mode (default mode) to application mode
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ minItems: 8
+ maxItems: 8
+
+ touchscreen-size-x: true
+ touchscreen-size-y: true
+ touchscreen-fuzz-x: true
+ touchscreen-fuzz-y: true
+
+ active-distance:
+ description: the distance in pixels beyond which a touch must move
+ before movement is detected and reported by the device
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+
+ active-interval-ms:
+ description: the minimum period in ms between consecutive
+ scanning/processing cycles when the chip is in active mode
+ minimum: 0
+ maximum: 255
+
+ lowpower-interval-ms:
+ description: the minimum period in ms between consecutive
+ scanning/processing cycles when the chip is in low-power mode
+ minimum: 0
+ maximum: 2550
+
+ touch-timeout-ms:
+ description: minimum time in ms spent in the active power state while no
+ touches are detected before entering low-power mode
+ minimum: 0
+ maximum: 2550
+
+ use-handshake:
+ description: enable register-based handshake (boolean). This should only
+ be used if the chip is configured to use 'blocking communication with
+ timeout' (in this case the device generates an interrupt at the end of
+ every scanning/processing cycle)
+ $ref: /schemas/types.yaml#/definitions/flag
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - bootloader-key
+ - touchscreen-size-x
+ - touchscreen-size-y
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ num-cs = <1>;
+ cs-gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
+
+ touchscreen@0 {
+ compatible = "cypress,cy8ctma340";
+ reg = <0>;
+ interrupt-parent = <&gpio>;
+ interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&ldo_aux1_reg>;
+ vcpin-supply = <&ldo_aux2_reg>;
+ bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+ touchscreen-size-x = <480>;
+ touchscreen-size-y = <800>;
+ active-interval-ms = <0>;
+ touch-timeout-ms = <255>;
+ lowpower-interval-ms = <10>;
+ };
+ };
+
+...
deleted file mode 100644
@@ -1,93 +0,0 @@
-* Cypress cyttsp touchscreen controller
-
-Required properties:
- - compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi"
- - reg : Device I2C address or SPI chip select number
- - spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi)
- - interrupts : (gpio) interrupt to which the chip is connected
- (see interrupt binding[0]).
- - bootloader-key : the 8-byte bootloader key that is required to switch
- the chip from bootloader mode (default mode) to
- application mode.
- This property has to be specified as an array of 8
- '/bits/ 8' values.
-
-Optional properties:
- - reset-gpios : the reset gpio the chip is connected to
- (see GPIO binding[1] for more details).
- - touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
- - touchscreen-size-y : vertical resolution of touchscreen (in pixels)
- - touchscreen-fuzz-x : horizontal noise value of the absolute input device
- (in pixels)
- - touchscreen-fuzz-y : vertical noise value of the absolute input device
- (in pixels)
- - active-distance : the distance in pixels beyond which a touch must move
- before movement is detected and reported by the device.
- Valid values: 0-15.
- - active-interval-ms : the minimum period in ms between consecutive
- scanning/processing cycles when the chip is in active mode.
- Valid values: 0-255.
- - lowpower-interval-ms : the minimum period in ms between consecutive
- scanning/processing cycles when the chip is in low-power mode.
- Valid values: 0-2550
- - touch-timeout-ms : minimum time in ms spent in the active power state while no
- touches are detected before entering low-power mode.
- Valid values: 0-2550
- - use-handshake : enable register-based handshake (boolean). This should
- only be used if the chip is configured to use 'blocking
- communication with timeout' (in this case the device
- generates an interrupt at the end of every
- scanning/processing cycle).
-
-[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-[1]: Documentation/devicetree/bindings/gpio/gpio.txt
-
-Example:
- &i2c1 {
- /* ... */
- cyttsp@a {
- compatible = "cypress,cyttsp-i2c";
- reg = <0xa>;
- interrupt-parent = <&gpio0>;
- interrupts = <28 0>;
- reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
-
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
- touchscreen-fuzz-x = <4>;
- touchscreen-fuzz-y = <7>;
-
- bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
- active-distance = <8>;
- active-interval-ms = <0>;
- lowpower-interval-ms = <200>;
- touch-timeout-ms = <100>;
- };
-
- /* ... */
- };
-
- &mcspi1 {
- /* ... */
- cyttsp@0 {
- compatible = "cypress,cyttsp-spi";
- spi-max-frequency = <6000000>;
- reg = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <28 0>;
- reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
-
- touchscreen-size-x = <800>;
- touchscreen-size-y = <480>;
- touchscreen-fuzz-x = <4>;
- touchscreen-fuzz-y = <7>;
-
- bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
- active-distance = <8>;
- active-interval-ms = <0>;
- lowpower-interval-ms = <200>;
- touch-timeout-ms = <100>;
- };
-
- /* ... */
- };