new file mode 100644
@@ -0,0 +1,395 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/cs35l41.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic CS35L41 Speaker Amplifier
+
+maintainers:
+ - david.rhodes@cirrus.com
+
+description: |
+ CS35L41 is a boosted mono Class D amplifier with DSP
+ speaker protection and equalization
+
+properties:
+ compatible:
+ enum:
+ - cirrus,cs35l40
+ - cirrus,cs35l41
+
+ reg:
+ maxItems: 1
+
+ '#sound-dai-cells':
+ description:
+ The first cell indicating the audio interface.
+ const: 1
+
+ cirrus,boost-peak-milliamp:
+ description:
+ Boost-converter peak current limit in mA.
+ Configures the peak current by monitoring the current through the boost FET.
+ Range starts at 1600 mA and goes to a maximum of 4500 mA with increments
+ of 50 mA. See section 4.3.6 of the datasheet for details.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 1600
+ maximum: 4500
+ default: 4500
+
+ cirrus,boost-ind-nanohenry:
+ description:
+ Boost inductor value, expressed in nH. Valid
+ values include 1000, 1200, 1500 and 2200.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 1000
+ maximum: 2200
+
+ cirrus,boost-cap-microfarad:
+ description:
+ Total equivalent boost capacitance on the VBST
+ and VAMP pins, derated at 11 volts DC. The value must be rounded to the
+ nearest integer and expressed in uF.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+
+ cirrus,sclk-force-output:
+ description:
+ Audio serial port SCLK force
+ output control. Forces the SCLK to continue to drive even
+ if no ASP_TXn channels are enabled.
+ type: boolean
+
+ cirrus,lrclk-force-output:
+ description:
+ Audio serial port LRCLK force
+ output control. Forces the LRCLK to continue to drive even
+ if no ASP_TXn channels are enabled.
+ type: boolean
+
+ cirrus,right-channel-amp:
+ description:
+ Boolean to determine which channel
+ the amplifier is to receive the audio data on. If present the
+ amplifier receives data on the right channel of I2S data.
+ If not present the amplifier receives data on the left
+ channel of I2S data
+ type: boolean
+
+ cirrus,boost-ctl-millivolt:
+ description:
+ Boost Voltage Value. Configures the
+ boost converter's output voltage in mV. The range is from 2550 mV to
+ 11000 mV with increments of 50 mV. This will be the maximum voltage
+ in Class-H mode if 'classh-bst-max-limit' is set to 1, or the fixed
+ boost voltage if 'classh-bst-overide' is set to true.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 2550
+ maximum: 11000
+
+ cirrus,amp-gain-zc:
+ description:
+ Boolean to determine whether to use the amplifier
+ gain-change zero-crossing feature. If the feature is enabled, any
+ user-controlled amplifier gain change will occur on a zero-crossing point.
+ (Default) Disabled
+ type: boolean
+
+ cirrus,asp-sdout-hiz:
+ description:
+ Audio serial port SDOUT Hi-Z control. Sets the Hi-Z
+ configuration for SDOUT pin of amplifier.
+ 0 = Logic 0 during unused slots, and while all transmit channels disabled
+ 1 = Hi-Z during unused slots but logic 0 while all transmit channels disabled
+ 2 = (Default) Logic 0 during unused slots, but Hi-Z while all transmit channels disabled
+ 3 = Hi-Z during unused slots and while all transmit channels disabled
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3
+ default: 2
+
+ cirrus,temp-warn-threshold:
+ description:
+ Amplifier overtemperature warning threshold.
+ Configures the threshold at which the overtemperature warning condition occurs.
+ When the threshold is met, the ovetemperature warning attenuation is applied
+ and the TEMP_WARN_EINT interrupt status bit is set.
+ If TEMP_WARN_MASK = 0, INTb is asserted.
+ 0 = 105C
+ 1 = 115C
+ 2 = 125C (Default)
+ 3 = 135C
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3
+ default: 2
+
+ cirrus,hw-noise-gate-select:
+ description: Hardware Noise Gate feature. Each bit selects
+ a different block for detection.
+ 000000 - All noise gating functionality disabled
+ xxxxx1 - Amplifier noise gating detection enabled
+ xxxx1x - Boost converter DCM detection enabled
+ xxx1xx - VMON low power mode detection enabled
+ xx1xxx - IMON low power mode detection enabled
+ x1xxxx - VP brownout prevention detection enabled
+ 1xxxxx - VBST brownout prevention detection enabled
+ type: boolean
+
+ cirrus,hw-noise-gate-delay:
+ description: Time that the incoming audio signal must be
+ below the noise gate threshold prior to entering a noise gated state
+ 0 = 5 ms
+ 1 = 10 ms
+ 2 = 25 ms
+ 3 = 50 ms (default)
+ 4 = 100 ms
+ 5 = 250 ms
+ 6 = 500 ms
+ 7 = 1 s
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
+ default: 3
+
+ cirrus,hw-noise-gate-threshold:
+ description: Threshold of audio signal input which the
+ noise gate considers the input audio to be at a low enough level to be
+ valid to enter a noise gating state of operation.
+ 0 = 0.654 mVpk
+ 1 = 0.328 mVpk
+ 2 = 0.164 mVpk
+ 3 = 0.082 mVpk (default)
+ 4 = 0.041 mVpk
+ 5 = 0.021 mVpk
+ 6 = 0.010 mVpk
+ 7 = True zero data (no LSB dither)
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
+ default: 3
+
+ cirrus,dsp-noise-gate-enable:
+ description:
+ DSP Noise Gate feature. If present, noise gate feature will be enabled.
+ type: boolean
+
+ cirrus,dsp-noise-gate-threshold:
+ description:
+ Threshold of audio signal input which the
+ noise gate considers the input audio to be at a low enough level to be
+ valid to enter a noise gating state of operation.
+ 0 = -66 dBFS
+ 1 = -72 dBFS
+ 2 = -78 dBFS
+ 3 = -84 dBFS (default)
+ 4 = -90 dBFS
+ 5 = -96 dBFS
+ 6 = -102 dBFS
+ 7 = -108 dBFS
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
+ default: 3
+
+ cirrus,dsp-noise-gate-delay:
+ description:
+ Time that the incoming audio signal must be
+ below the noise gate threshold prior to entering a noise gated state
+ 0 = 5 ms
+ 1 = 10 ms
+ 2 = 25 ms
+ 3 = 50 ms (default)
+ 4 = 100 ms
+ 5 = 250 ms
+ 6 = 500 ms
+ 7 = 1 s
+ 8 = 5 s
+ 9 = 10 s
+ 10 = 20 s
+ 11 = 30 s
+ 12 = 40 s
+ 13 = 50 s
+ 14 = 60 s
+ 15 = 120 s
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 15
+ default: 3
+
+ cirrus,invert-pcm:
+ description:
+ Inverts the polarity of the audio signal output from
+ the Class-D amplifier.
+ type: boolean
+
+ classh-internal-algo:
+ description:
+ Sub-node for the Internal Class H Algorithm
+ See Section 4.4 Internal Class H Algorithm in the Datasheet.
+ If not used, the device manages the ClassH Algorithm internally.
+ It is strongly recommended that the Datasheet be referenced when adjusting
+ or using these Class H Algorithm controls over the internal Algorithm.
+ Serious damage can occur to the Device and surrounding components.
+ Unavailable for cs35l41l.
+ type:
+ boolean
+ cirrus,classh-bst-overide:
+ description:
+ Boolean which will disable Class H tracking and
+ set Boost voltage to the value in the 'boost-ctl-millivolt' property
+ type: boolean
+ cirrus,classh-bst-max-limit:
+ description:
+ Value set to the BST_CTL_LIM_EN field.
+ A value of 1 will limit the Class-H voltage to the value in the
+ 'boost-ctl-millivolt' property.
+ 0 = No Class-H limit (default)
+ 1 = Class-H limited to 'boost-ctl-millivolt' value
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1
+ cirrus,classh-headroom:
+ description:
+ Class H algorithm headroom. Controls VBST headroom
+ in the max detection path of the Class H algorithm. Step size is 0.1 V.
+ Range is from -6.4V to +6.3V with 7-bit 2's complement representation.
+ 0 = 0V
+ 1 = 0.1V
+ 2 = 0.2V
+ ===
+ 11 = 1.1V (Default)
+ ===
+ 62 = 6.2V
+ 63 = 6.3V
+ 64 = -6.4V
+ 65 = -6.3V
+ ===
+ 126 = -0.2V
+ 127 = -0.1V
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 127
+ cirrus,classh-release-rate:
+ description:
+ Class H release rate. Controls the amount of
+ time required before allowing consecutive release condition VBST supply
+ tracking updates. Step size is 5us with range from 20us to 1275us.
+ 4 = 20us (Default)
+ 5 = 25us
+ ===
+ 254 = 1270us
+ 255 = 1275us
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 4
+ maximum: 255
+ cirrus,classh-mem-depth:
+ description:
+ Class H memory depth. Controls the memory depth
+ used in the Class H algorithm for audio data buffering and analysis.
+ 0 = 20.83 - 23.4 us
+ 1 = 41.67 - 46.88 us
+ 2 = 83.33 - 85.94 us
+ 3 = 166.67 - 171.88 us
+ 4 = 250.00 - 255.10 us
+ 5 = 333.33 - 335.93 us (Default)
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 5
+ cirrus,classh-wk-fet-thld:
+ description:
+ Weak-FET amplifier driver threshold.
+ Configures the signal threshold at which the PWM output stage enters weak-FET
+ operation. Step size is 0.05V. Range is from 0.05V to 0.7V.
+ 1 = 0.05V
+ 2 = 0.1V
+ 3 = 0.15V
+ ===
+ 13 = 0.65V
+ 14 = 0.7V
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 1
+ maximum: 14
+ cirrus,classh-wk-fet-delay:
+ description:
+ Weak-Fet entry . Controls the delay in ms
+ before the Class H algorithm switches to the weak-FET voltage after the audio
+ falls and remains below the value specified in 'classh-wk-fet-thld'.
+ 0 = 0ms
+ 1 = 5ms
+ 2 = 10ms
+ 3 = 50ms
+ 4 = 100ms (Default)
+ 5 = 200ms
+ 6 = 500ms
+ 7 = 1000ms
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
+ cirrus,gpio1-polarity-invert:
+ description:
+ Boolean which specifies whether the GPIO1
+ level is inverted. If this property is not present the level is not inverted.
+ type: boolean
+ cirrus,gpio1-output-enable:
+ description:
+ Boolean which specifies whether the GPIO1 pin
+ is configured as an output. If this property is not present the
+ pin will be configured as an input.
+ type: boolean
+ cirrus,gpio1-src-select:
+ description:
+ Configures the function of the GPIO1 pin.
+ Note that the options are different from the GPIO2 pin
+ 0 = High Impedance (Default)
+ 1 = GPIO
+ 2 = Sync
+ 3 = MCLK input
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3
+ cirrus,gpio2-polarity-invert:
+ description:
+ Boolean which specifies whether the GPIO2
+ level is inverted. If this property is not present the level is not inverted.
+ type: boolean
+ cirrus,gpio2-output-enable:
+ description:
+ Boolean which specifies whether the GPIO2 pin
+ is configured as an output. If this property is not present the
+ pin will be configured as an input.
+ type: boolean
+ cirrus,gpio2-src-select:
+ description:
+ Configures the function of the GPIO2 pin.
+ Note that the options are different from the GPIO1 pin.
+ 0 = High Impedance (Default)
+ 1 = GPIO
+ 2 = Open Drain INTB
+ 3 = MCLK input
+ 4 = Push-pull INTB (active low)
+ 5 = Push-pull INT (active high)
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 5
+
+required:
+ - compatible
+ - cirrus,boost-peak-milliamp
+ - cirrus,boost-ind-nanohenry
+ - cirrus,boost-cap-microfarad
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ cs35l41: cs35l41@2 {
+ compatible = "cirrus,cs35l41";
+ reg = <2>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ cirrus,boost-peak-milliamp = <4500>;
+ cirrus,boost-ind-nanohenry = <1000>;
+ cirrus,boost-cap-microfarad = <15>;
+ };
\ No newline at end of file
Devicetree binding documentation for CS35L41 driver CS35L41 is a 11-V Boosted Mono Class D Amplifier with DSP Speaker Protection and Equalization Signed-off-by: David Rhodes <drhodes@opensource.cirrus.com> --- .../devicetree/bindings/sound/cs35l41.yaml | 395 ++++++++++++++++++ 1 file changed, 395 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/cs35l41.yaml