diff mbox series

serial: amba-pl011: add RS485 support

Message ID 20210610135004.7585-1-LinoSanfilippo@gmx.de
State Superseded
Headers show
Series serial: amba-pl011: add RS485 support | expand

Commit Message

Lino Sanfilippo June 10, 2021, 1:50 p.m. UTC 
Add basic support for RS485: Provide a callback to configure rs485
settings. Handle the RS485 specific part in the functions
pl011_rs485_tx_start() and pl011_rs485_tx_stop() which extend the generic
start/stop callbacks.
Beside via IOCTL from userspace RS485 can be enabled by means of the
device tree property "rs485-enabled-at-boot-time".

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
---
This patch has been tested with a Raspberry Pi CM3.

 drivers/tty/serial/amba-pl011.c | 143 +++++++++++++++++++++++++++++++-
 1 file changed, 140 insertions(+), 3 deletions(-)


base-commit: cd1245d75ce93b8fd206f4b34eb58bcfe156d5e9

Comments

Jiri Slaby June 16, 2021, 6:18 a.m. UTC | #1 
On 10. 06. 21, 15:50, Lino Sanfilippo wrote:
> Add basic support for RS485: Provide a callback to configure rs485

> settings. Handle the RS485 specific part in the functions

> pl011_rs485_tx_start() and pl011_rs485_tx_stop() which extend the generic

> start/stop callbacks.

> Beside via IOCTL from userspace RS485 can be enabled by means of the

> device tree property "rs485-enabled-at-boot-time".

> 

> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>

> ---

> This patch has been tested with a Raspberry Pi CM3.

> 

>   drivers/tty/serial/amba-pl011.c | 143 +++++++++++++++++++++++++++++++-

>   1 file changed, 140 insertions(+), 3 deletions(-)

> 

> diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c

> index 78682c12156a..36e8b938cdba 100644

> --- a/drivers/tty/serial/amba-pl011.c

> +++ b/drivers/tty/serial/amba-pl011.c

...
> @@ -1380,6 +1415,31 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,

>   	return true;

>   }

>   

> +static void pl011_rs485_tx_start(struct uart_amba_port *uap)

> +{

> +	struct uart_port *port = &uap->port;

> +	u32 cr;

> +

> +	/* Enable transmitter */

> +	cr = pl011_read(uap, REG_CR);

> +	cr |= UART011_CR_TXE;

> +	/* Disable receiver if half-duplex */

> +	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))

> +		cr &= ~UART011_CR_RXE;

> +

> +	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)

> +		cr &= ~UART011_CR_RTS;

> +	else

> +		cr |= UART011_CR_RTS;

> +

> +	pl011_write(cr, uap, REG_CR);

> +

> +	if (port->rs485.delay_rts_before_send)

> +		mdelay(port->rs485.delay_rts_before_send);


This is up to 1 second delay with interrupts disabled. Definitely not 
nice. 8250 clamps this to 100 ms at least, why did you choose 1000 ms?

> +

> +	uap->rs485_tx_started = true;

> +}

> +

>   /* Returns true if tx interrupts have to be (kept) enabled  */

>   static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)

>   {

...
> @@ -1941,6 +2021,7 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,

>   	unsigned int lcr_h, old_cr;

>   	unsigned long flags;

>   	unsigned int baud, quot, clkdiv;

> +	unsigned int bits;

>   

>   	if (uap->vendor->oversampling)

>   		clkdiv = 8;

> @@ -1968,25 +2049,32 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,

>   	switch (termios->c_cflag & CSIZE) {

>   	case CS5:

>   		lcr_h = UART01x_LCRH_WLEN_5;

> +		bits = 7;

>   		break;

>   	case CS6:

>   		lcr_h = UART01x_LCRH_WLEN_6;

> +		bits = 8;

>   		break;

>   	case CS7:

>   		lcr_h = UART01x_LCRH_WLEN_7;

> +		bits = 9;

>   		break;

>   	default: // CS8

>   		lcr_h = UART01x_LCRH_WLEN_8;

> +		bits = 10;

>   		break;

>   	}

> -	if (termios->c_cflag & CSTOPB)

> +	if (termios->c_cflag & CSTOPB) {

>   		lcr_h |= UART01x_LCRH_STP2;

> +		bits++;

> +	}

>   	if (termios->c_cflag & PARENB) {

>   		lcr_h |= UART01x_LCRH_PEN;

>   		if (!(termios->c_cflag & PARODD))

>   			lcr_h |= UART01x_LCRH_EPS;

>   		if (termios->c_cflag & CMSPAR)

>   			lcr_h |= UART011_LCRH_SPS;

> +		bits++;

>   	}


You can do simply:
   bits = tty_get_frame_size(termios->c_cflag);
now:
https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git/commit/?h=tty-testing&id=3ec2ff37230e1c961d4b0d0118dd23c46b5bcdbb


thanks,
-- 
js
Greg KH June 16, 2021, 6:29 a.m. UTC | #2 
On Wed, Jun 16, 2021 at 08:18:01AM +0200, Jiri Slaby wrote:
> On 10. 06. 21, 15:50, Lino Sanfilippo wrote:

> > Add basic support for RS485: Provide a callback to configure rs485

> > settings. Handle the RS485 specific part in the functions

> > pl011_rs485_tx_start() and pl011_rs485_tx_stop() which extend the generic

> > start/stop callbacks.

> > Beside via IOCTL from userspace RS485 can be enabled by means of the

> > device tree property "rs485-enabled-at-boot-time".

> > 

> > Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>

> > ---

> > This patch has been tested with a Raspberry Pi CM3.

> > 

> >   drivers/tty/serial/amba-pl011.c | 143 +++++++++++++++++++++++++++++++-

> >   1 file changed, 140 insertions(+), 3 deletions(-)

> > 

> > diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c

> > index 78682c12156a..36e8b938cdba 100644

> > --- a/drivers/tty/serial/amba-pl011.c

> > +++ b/drivers/tty/serial/amba-pl011.c

> ...

> > @@ -1380,6 +1415,31 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,

> >   	return true;

> >   }

> > +static void pl011_rs485_tx_start(struct uart_amba_port *uap)

> > +{

> > +	struct uart_port *port = &uap->port;

> > +	u32 cr;

> > +

> > +	/* Enable transmitter */

> > +	cr = pl011_read(uap, REG_CR);

> > +	cr |= UART011_CR_TXE;

> > +	/* Disable receiver if half-duplex */

> > +	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))

> > +		cr &= ~UART011_CR_RXE;

> > +

> > +	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)

> > +		cr &= ~UART011_CR_RTS;

> > +	else

> > +		cr |= UART011_CR_RTS;

> > +

> > +	pl011_write(cr, uap, REG_CR);

> > +

> > +	if (port->rs485.delay_rts_before_send)

> > +		mdelay(port->rs485.delay_rts_before_send);

> 

> This is up to 1 second delay with interrupts disabled. Definitely not nice.

> 8250 clamps this to 100 ms at least, why did you choose 1000 ms?

> 

> > +

> > +	uap->rs485_tx_started = true;

> > +}

> > +

> >   /* Returns true if tx interrupts have to be (kept) enabled  */

> >   static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)

> >   {

> ...

> > @@ -1941,6 +2021,7 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,

> >   	unsigned int lcr_h, old_cr;

> >   	unsigned long flags;

> >   	unsigned int baud, quot, clkdiv;

> > +	unsigned int bits;

> >   	if (uap->vendor->oversampling)

> >   		clkdiv = 8;

> > @@ -1968,25 +2049,32 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,

> >   	switch (termios->c_cflag & CSIZE) {

> >   	case CS5:

> >   		lcr_h = UART01x_LCRH_WLEN_5;

> > +		bits = 7;

> >   		break;

> >   	case CS6:

> >   		lcr_h = UART01x_LCRH_WLEN_6;

> > +		bits = 8;

> >   		break;

> >   	case CS7:

> >   		lcr_h = UART01x_LCRH_WLEN_7;

> > +		bits = 9;

> >   		break;

> >   	default: // CS8

> >   		lcr_h = UART01x_LCRH_WLEN_8;

> > +		bits = 10;

> >   		break;

> >   	}

> > -	if (termios->c_cflag & CSTOPB)

> > +	if (termios->c_cflag & CSTOPB) {

> >   		lcr_h |= UART01x_LCRH_STP2;

> > +		bits++;

> > +	}

> >   	if (termios->c_cflag & PARENB) {

> >   		lcr_h |= UART01x_LCRH_PEN;

> >   		if (!(termios->c_cflag & PARODD))

> >   			lcr_h |= UART01x_LCRH_EPS;

> >   		if (termios->c_cflag & CMSPAR)

> >   			lcr_h |= UART011_LCRH_SPS;

> > +		bits++;

> >   	}

> 

> You can do simply:

>   bits = tty_get_frame_size(termios->c_cflag);

> now:

> https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git/commit/?h=tty-testing&id=3ec2ff37230e1c961d4b0d0118dd23c46b5bcdbb


I was wondering about that.

I'll go drop this patch from my tty-next branch and wait for a new
version that fixes the above delay issue and it can use this new call as
well.

thanks,

greg k-h
Lino Sanfilippo June 17, 2021, 4:12 p.m. UTC | #3 
Hi,

On 16.06.21 at 08:18, Jiri Slaby wrote:

>> +    if (port->rs485.delay_rts_before_send)

>> +        mdelay(port->rs485.delay_rts_before_send);

>

> This is up to 1 second delay with interrupts disabled. Definitely not nice. 8250 clamps this to 100 ms at least, why did you choose 1000 ms?

>


I got this value from rs485.yaml where the max number for both rts delay before and after send
is specified as 1000ms. I thought to keep it up to the user to choose a sane setting. But yes,
its a very long time with interrupts disabled. I will send an updated version of this patch that
limits both values to 100ms.


os(struct uart_port *port, struct ktermios *termios,
>>       unsigned int lcr_h, old_cr;

>>       unsigned long flags;

>>       unsigned int baud, quot, clkdiv;

>> +    unsigned int bits;

>>         if (uap->vendor->oversampling)

>>           clkdiv = 8;

>> @@ -1968,25 +2049,32 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,

>>       switch (termios->c_cflag & CSIZE) {

>>       case CS5:

>>           lcr_h = UART01x_LCRH_WLEN_5;

>> +        bits = 7;

>>           break;

>>       case CS6:

>>           lcr_h = UART01x_LCRH_WLEN_6;

>> +        bits = 8;

>>           break;

>>       case CS7:

>>           lcr_h = UART01x_LCRH_WLEN_7;

>> +        bits = 9;

>>           break;

>>       default: // CS8

>>           lcr_h = UART01x_LCRH_WLEN_8;

>> +        bits = 10;

>>           break;

>>       }

>> -    if (termios->c_cflag & CSTOPB)

>> +    if (termios->c_cflag & CSTOPB) {

>>           lcr_h |= UART01x_LCRH_STP2;

>> +        bits++;

>> +    }

>>       if (termios->c_cflag & PARENB) {

>>           lcr_h |= UART01x_LCRH_PEN;

>>           if (!(termios->c_cflag & PARODD))

>>               lcr_h |= UART01x_LCRH_EPS;

>>           if (termios->c_cflag & CMSPAR)

>>               lcr_h |= UART011_LCRH_SPS;

>> +        bits++;

>>       }

>

> You can do simply:

>   bits = tty_get_frame_size(termios->c_cflag);

> now:

> https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git/commit/?h=tty-testing&id=3ec2ff37230e1c961d4b0d0118dd23c46b5bcdbb


Ah thats a nice function, thanks for pointing at it. I will adjust the code accordingly.


>

> thanks,


Thanks for the review!

Regards,
Lino
Lino Sanfilippo June 17, 2021, 5:44 p.m. UTC | #4 
Hi,

On 16.06.21 at 08:18, Jiri Slaby wrote:
        mdelay(port->rs485.delay_rts_before_send);
>

> This is up to 1 second delay with interrupts disabled. Definitely not nice. 8250 clamps this to 100 ms at least, why did you choose 1000 ms?

>


AFAICS the 8250 driver does not clamp values read from the device tree property "rs485-rts-delay"
(set by uart_get_rs485_mode()). Is this on purpose?

Regards,
Lino
diff mbox series

Patch

diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 78682c12156a..36e8b938cdba 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -265,6 +265,8 @@  struct uart_amba_port {
 	unsigned int		old_cr;		/* state during shutdown */
 	unsigned int		fixed_baud;	/* vendor-set fixed baud rate */
 	char			type[12];
+	bool			rs485_tx_started;
+	unsigned int		rs485_tx_drain_interval; /* usecs */
 #ifdef CONFIG_DMA_ENGINE
 	/* DMA stuff */
 	bool			using_tx_dma;
@@ -275,6 +277,8 @@  struct uart_amba_port {
 #endif
 };
 
+static unsigned int pl011_tx_empty(struct uart_port *port);
+
 static unsigned int pl011_reg_to_offset(const struct uart_amba_port *uap,
 	unsigned int reg)
 {
@@ -1282,6 +1286,34 @@  static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
 #define pl011_dma_flush_buffer	NULL
 #endif
 
+static int pl011_rs485_tx_stop(struct uart_amba_port *uap)
+{
+	struct uart_port *port = &uap->port;
+	u32 cr;
+
+	/* Wait until hardware tx queue is empty */
+	while (!pl011_tx_empty(port))
+		udelay(uap->rs485_tx_drain_interval);
+
+	if (port->rs485.delay_rts_after_send)
+		mdelay(port->rs485.delay_rts_after_send);
+
+	cr = pl011_read(uap, REG_CR);
+
+	if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
+		cr &= ~UART011_CR_RTS;
+	else
+		cr |= UART011_CR_RTS;
+	/* Disable the transmitter and reenable the transceiver */
+	cr &= ~UART011_CR_TXE;
+	cr |= UART011_CR_RXE;
+	pl011_write(cr, uap, REG_CR);
+
+	uap->rs485_tx_started = false;
+
+	return 0;
+}
+
 static void pl011_stop_tx(struct uart_port *port)
 {
 	struct uart_amba_port *uap =
@@ -1290,6 +1322,9 @@  static void pl011_stop_tx(struct uart_port *port)
 	uap->im &= ~UART011_TXIM;
 	pl011_write(uap->im, uap, REG_IMSC);
 	pl011_dma_tx_stop(uap);
+
+	if ((port->rs485.flags & SER_RS485_ENABLED) && uap->rs485_tx_started)
+		pl011_rs485_tx_stop(uap);
 }
 
 static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
@@ -1380,6 +1415,31 @@  static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
 	return true;
 }
 
+static void pl011_rs485_tx_start(struct uart_amba_port *uap)
+{
+	struct uart_port *port = &uap->port;
+	u32 cr;
+
+	/* Enable transmitter */
+	cr = pl011_read(uap, REG_CR);
+	cr |= UART011_CR_TXE;
+	/* Disable receiver if half-duplex */
+	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
+		cr &= ~UART011_CR_RXE;
+
+	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
+		cr &= ~UART011_CR_RTS;
+	else
+		cr |= UART011_CR_RTS;
+
+	pl011_write(cr, uap, REG_CR);
+
+	if (port->rs485.delay_rts_before_send)
+		mdelay(port->rs485.delay_rts_before_send);
+
+	uap->rs485_tx_started = true;
+}
+
 /* Returns true if tx interrupts have to be (kept) enabled  */
 static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 {
@@ -1397,6 +1457,10 @@  static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 		return false;
 	}
 
+	if ((uap->port.rs485.flags & SER_RS485_ENABLED) &&
+	    !uap->rs485_tx_started)
+		pl011_rs485_tx_start(uap);
+
 	/* If we are using DMA mode, try to send some characters. */
 	if (pl011_dma_tx_irq(uap))
 		return true;
@@ -1542,6 +1606,9 @@  static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	    container_of(port, struct uart_amba_port, port);
 	unsigned int cr;
 
+	if (port->rs485.flags & SER_RS485_ENABLED)
+		mctrl &= ~TIOCM_RTS;
+
 	cr = pl011_read(uap, REG_CR);
 
 #define	TIOCMBIT(tiocmbit, uartbit)		\
@@ -1763,7 +1830,17 @@  static int pl011_startup(struct uart_port *port)
 
 	/* restore RTS and DTR */
 	cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR);
-	cr |= UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
+	cr |= UART01x_CR_UARTEN | UART011_CR_RXE;
+
+	if (port->rs485.flags & SER_RS485_ENABLED) {
+		if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
+			cr &= ~UART011_CR_RTS;
+		else
+			cr |= UART011_CR_RTS;
+	} else {
+		cr |= UART011_CR_TXE;
+	}
+
 	pl011_write(cr, uap, REG_CR);
 
 	spin_unlock_irq(&uap->port.lock);
@@ -1864,6 +1941,9 @@  static void pl011_shutdown(struct uart_port *port)
 
 	pl011_dma_shutdown(uap);
 
+	if ((port->rs485.flags & SER_RS485_ENABLED) && uap->rs485_tx_started)
+		pl011_rs485_tx_stop(uap);
+
 	free_irq(uap->port.irq, uap);
 
 	pl011_disable_uart(uap);
@@ -1941,6 +2021,7 @@  pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 	unsigned int lcr_h, old_cr;
 	unsigned long flags;
 	unsigned int baud, quot, clkdiv;
+	unsigned int bits;
 
 	if (uap->vendor->oversampling)
 		clkdiv = 8;
@@ -1968,25 +2049,32 @@  pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 	switch (termios->c_cflag & CSIZE) {
 	case CS5:
 		lcr_h = UART01x_LCRH_WLEN_5;
+		bits = 7;
 		break;
 	case CS6:
 		lcr_h = UART01x_LCRH_WLEN_6;
+		bits = 8;
 		break;
 	case CS7:
 		lcr_h = UART01x_LCRH_WLEN_7;
+		bits = 9;
 		break;
 	default: // CS8
 		lcr_h = UART01x_LCRH_WLEN_8;
+		bits = 10;
 		break;
 	}
-	if (termios->c_cflag & CSTOPB)
+	if (termios->c_cflag & CSTOPB) {
 		lcr_h |= UART01x_LCRH_STP2;
+		bits++;
+	}
 	if (termios->c_cflag & PARENB) {
 		lcr_h |= UART01x_LCRH_PEN;
 		if (!(termios->c_cflag & PARODD))
 			lcr_h |= UART01x_LCRH_EPS;
 		if (termios->c_cflag & CMSPAR)
 			lcr_h |= UART011_LCRH_SPS;
+		bits++;
 	}
 	if (uap->fifosize > 1)
 		lcr_h |= UART01x_LCRH_FEN;
@@ -1997,12 +2085,21 @@  pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 	 * Update the per-port timeout.
 	 */
 	uart_update_timeout(port, termios->c_cflag, baud);
+	/*
+	 * Calculate the approximated time it takes to transmit one character
+	 * with the given baud rate. We use this as the poll interval when we
+	 * wait for the tx queue to empty.
+	 */
+	uap->rs485_tx_drain_interval = (bits * 1000 * 1000) / baud;
 
 	pl011_setup_status_masks(port, termios);
 
 	if (UART_ENABLE_MS(port, termios->c_cflag))
 		pl011_enable_ms(port);
 
+	if (port->rs485.flags & SER_RS485_ENABLED)
+		termios->c_cflag &= ~CRTSCTS;
+
 	/* first, disable everything */
 	old_cr = pl011_read(uap, REG_CR);
 	pl011_write(0, uap, REG_CR);
@@ -2124,6 +2221,41 @@  static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser)
 	return ret;
 }
 
+static int pl011_rs485_config(struct uart_port *port,
+			      struct serial_rs485 *rs485)
+{
+	struct uart_amba_port *uap =
+		container_of(port, struct uart_amba_port, port);
+
+	/* pick sane settings if the user hasn't */
+	if (!!(rs485->flags & SER_RS485_RTS_ON_SEND) ==
+	    !!(rs485->flags & SER_RS485_RTS_AFTER_SEND)) {
+		rs485->flags |= SER_RS485_RTS_ON_SEND;
+		rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
+	}
+
+	rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 1000U);
+	rs485->delay_rts_after_send = min(rs485->delay_rts_after_send, 1000U);
+	memset(rs485->padding, 0, sizeof(rs485->padding));
+
+	if (port->rs485.flags & SER_RS485_ENABLED)
+		pl011_rs485_tx_stop(uap);
+
+	/* Set new configuration */
+	port->rs485 = *rs485;
+	/* Make sure auto RTS is disabled */
+	if (port->rs485.flags & SER_RS485_ENABLED) {
+		u32 cr = pl011_read(uap, REG_CR);
+
+		cr &= ~UART011_CR_RTSEN;
+		pl011_write(cr, uap, REG_CR);
+		port->status &= ~UPSTAT_AUTORTS;
+	}
+
+
+	return 0;
+}
+
 static const struct uart_ops amba_pl011_pops = {
 	.tx_empty	= pl011_tx_empty,
 	.set_mctrl	= pl011_set_mctrl,
@@ -2592,6 +2724,7 @@  static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap,
 			    struct resource *mmiobase, int index)
 {
 	void __iomem *base;
+	int ret;
 
 	base = devm_ioremap_resource(dev, mmiobase);
 	if (IS_ERR(base))
@@ -2608,6 +2741,10 @@  static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap,
 	uap->port.flags = UPF_BOOT_AUTOCONF;
 	uap->port.line = index;
 
+	ret = uart_get_rs485_mode(&uap->port);
+	if (ret)
+		return ret;
+
 	amba_ports[index] = uap;
 
 	return 0;
@@ -2665,7 +2802,7 @@  static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
 	uap->port.iotype = vendor->access_32b ? UPIO_MEM32 : UPIO_MEM;
 	uap->port.irq = dev->irq[0];
 	uap->port.ops = &amba_pl011_pops;
-
+	uap->port.rs485_config = pl011_rs485_config;
 	snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev));
 
 	ret = pl011_setup_port(&dev->dev, uap, &dev->res, portnr);