diff mbox series

[v8,1/9] dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller

Message ID 20210611061134.31369-2-jon.lin@rock-chips.com
State Superseded
Headers show
Series Add Rockchip SFC(serial flash controller) support | expand

Commit Message

Jon Lin June 11, 2021, 6:11 a.m. UTC
From: Chris Morgan <macromorgan@hotmail.com>

Add bindings for the Rockchip serial flash controller. New device
specific parameter of rockchip,sfc-no-dma included in documentation.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
---

Changes in v8:
- Fix indent 4 to 2 in yaml

Changes in v7:
- Fix up the sclk_sfc parent error in rk3036
- Unify to "rockchip,sfc" compatible id because all the feature update
  will have a new IP version, so the driver is used for the SFC IP in
  all SoCs
- Change to use node "sfc" to name the SFC pinctrl group
- Add subnode reg property check
- Add rockchip_sfc_adjust_op_size to workaround in CMD + DUMMY case
- Limit max_iosize to 32KB

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not
  submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not
  affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared
  in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip
  reached out to me to let me know they are working on this patch for
  upstream, I am submitting this v4 for the community to see however
  I expect Jon Lin (jon.lin@rock-chips.com) will submit new patches
  soon and these are the ones we should pursue for mainlining. Jon's
  patch series should include support for more hardware than this
  series.
- Clean up documentation more and ensure it is correct per
  make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the
  specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to
  rockchip,rk3036-sfc. A quick glance at the datasheets suggests this
  driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and
  RV1108 SoCs, and possibly more. However, I am currently only able
  to test this on a PX30 (an RK3326). The technical reference manuals
  appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these
  changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will
  take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but
  I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the
  event that the SPI chip supports 4x mode but only has 2 pins
  wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when
  starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just
  dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

 .../devicetree/bindings/spi/rockchip-sfc.yaml | 88 +++++++++++++++++++
 1 file changed, 88 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Comments

Rob Herring June 24, 2021, 7:04 p.m. UTC | #1
On Fri, Jun 11, 2021 at 02:11:26PM +0800, Jon Lin wrote:
> From: Chris Morgan <macromorgan@hotmail.com>

> 

> Add bindings for the Rockchip serial flash controller. New device

> specific parameter of rockchip,sfc-no-dma included in documentation.

> 

> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>

> Signed-off-by: Jon Lin <jon.lin@rock-chips.com>

> ---

> 

> Changes in v8:

> - Fix indent 4 to 2 in yaml


My comments from v7 remain.

> 

> Changes in v7:

> - Fix up the sclk_sfc parent error in rk3036

> - Unify to "rockchip,sfc" compatible id because all the feature update

>   will have a new IP version, so the driver is used for the SFC IP in

>   all SoCs

> - Change to use node "sfc" to name the SFC pinctrl group

> - Add subnode reg property check

> - Add rockchip_sfc_adjust_op_size to workaround in CMD + DUMMY case

> - Limit max_iosize to 32KB

> 

> Changes in v6:

> - Add support in device trees for rv1126(Declared in series 5 but not

>   submitted)

> - Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not

>   affect interpretation and has been widely used

> - Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)

> - Simplify the code, such as remove "rockchip_sfc_register_all"(Declared

>   in series 5 but not submitted)

> - Support SFC ver4 ver5(Declared in series 5 but not submitted)

> - Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c

> - Change to use devm_spi_alloc_master and spi_unregister_master

> 

> Changes in v5:

> - Add support in device trees for rv1126

> - Support sfc tx_dual, tx_quad

> - Simplify the code, such as remove "rockchip_sfc_register_all"

> - Support SFC ver4 ver5

> 

> Changes in v4:

> - Changing patch back to an "RFC". An engineer from Rockchip

>   reached out to me to let me know they are working on this patch for

>   upstream, I am submitting this v4 for the community to see however

>   I expect Jon Lin (jon.lin@rock-chips.com) will submit new patches

>   soon and these are the ones we should pursue for mainlining. Jon's

>   patch series should include support for more hardware than this

>   series.

> - Clean up documentation more and ensure it is correct per

>   make dt_binding_check.

> - Add support in device trees for rk3036, rk3308, and rv1108.

> - Add ahb clock (hclk_sfc) support for rk3036.

> - Change rockchip_sfc_wait_fifo_ready() to use a switch statement.

> - Change IRQ code to only mark IRQ as handled if it handles the

>   specific IRQ (DMA transfer finish) it is supposed to handle.

> 

> Changes in v3:

> - Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).

> - Changed the compatible string from rockchip,sfc to

>   rockchip,rk3036-sfc. A quick glance at the datasheets suggests this

>   driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and

>   RV1108 SoCs, and possibly more. However, I am currently only able

>   to test this on a PX30 (an RK3326). The technical reference manuals

>   appear to list the same registers for each device.

> - Corrected devicetree documentation for formatting and to note these

>   changes.

> - Replaced the maintainer with Heiko Stuebner and myself, as we will

>   take ownership of this going forward.

> - Noted that the device (per the reference manual) supports 4 CS, but

>   I am only able to test a single CS (CS 0).

> - Reordered patches to comply with upstream rules.

> 

> Changes in v2:

> - Reimplemented driver using spi-mem subsystem.

> - Removed power management code as I couldn't get it working properly.

> - Added device tree bindings for Odroid Go Advance.

> 

> Changes in v1:

> hanges made in this new series versus the v8 of the old series:

> - Added function to read spi-rx-bus-width from device tree, in the

>   event that the SPI chip supports 4x mode but only has 2 pins

>   wired (such as the Odroid Go Advance).

> - Changed device tree documentation from txt to yaml format.

> - Made "reset" message a dev_dbg from a dev_info.

> - Changed read and write fifo functions to remove redundant checks.

> - Changed the write and read from relaxed to non-relaxed when

>   starting the DMA transfer or reading the DMA IRQ.

> - Changed from dma_coerce_mask_and_coherent to just

>   dma_set_mask_and_coherent.

> - Changed name of get_if_type to rockchip_sfc_get_if_type.

> 

>  .../devicetree/bindings/spi/rockchip-sfc.yaml | 88 +++++++++++++++++++

>  1 file changed, 88 insertions(+)

>  create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

> 

> diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

> new file mode 100644

> index 000000000000..162993a97290

> --- /dev/null

> +++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

> @@ -0,0 +1,88 @@

> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)

> +%YAML 1.2

> +---

> +$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#

> +$schema: http://devicetree.org/meta-schemas/core.yaml#

> +

> +title: Rockchip Serial Flash Controller (SFC)

> +

> +maintainers:

> +  - Heiko Stuebner <heiko@sntech.de>

> +  - Chris Morgan <macromorgan@hotmail.com>

> +

> +allOf:

> +  - $ref: spi-controller.yaml#

> +

> +properties:

> +  compatible:

> +    oneOf:

> +      - const: rockchip,sfc

> +

> +  reg:

> +    maxItems: 1

> +

> +  interrupts:

> +    maxItems: 1

> +

> +  clocks:

> +    items:

> +      - description: Bus Clock

> +      - description: Module Clock

> +

> +  clock-names:

> +    items:

> +      - const: clk_sfc

> +      - const: hclk_sfc

> +

> +  power-domains:

> +    maxItems: 1

> +

> +  rockchip,sfc-no-dma:

> +    description: Disable DMA and utilize FIFO mode only

> +    type: boolean

> +

> +patternProperties:

> +  "^flash@[0-3]$":

> +    type: object

> +    properties:

> +      reg:

> +        minimum: 0

> +        maximum: 3

> +

> +required:

> +  - compatible

> +  - reg

> +  - interrupts

> +  - clocks

> +  - clock-names

> +

> +unevaluatedProperties: false

> +

> +examples:

> +  - |

> +    #include <dt-bindings/clock/px30-cru.h>

> +    #include <dt-bindings/interrupt-controller/arm-gic.h>

> +    #include <dt-bindings/power/px30-power.h>

> +

> +    sfc: spi@ff3a0000 {

> +        compatible = "rockchip,sfc";

> +        reg = <0xff3a0000 0x4000>;

> +        interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;

> +        clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;

> +        clock-names = "clk_sfc", "hclk_sfc";

> +        pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;

> +        pinctrl-names = "default";

> +        power-domains = <&power PX30_PD_MMC_NAND>;

> +        #address-cells = <1>;

> +        #size-cells = <0>;

> +

> +        flash@0 {

> +            compatible = "jedec,spi-nor";

> +            reg = <0>;

> +            spi-max-frequency = <108000000>;

> +            spi-rx-bus-width = <2>;

> +            spi-tx-bus-width = <2>;

> +        };

> +    };

> +

> +...

> -- 

> 2.17.1

> 

> 

> 

>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
new file mode 100644
index 000000000000..162993a97290
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
@@ -0,0 +1,88 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip Serial Flash Controller (SFC)
+
+maintainers:
+  - Heiko Stuebner <heiko@sntech.de>
+  - Chris Morgan <macromorgan@hotmail.com>
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - const: rockchip,sfc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: clk_sfc
+      - const: hclk_sfc
+
+  power-domains:
+    maxItems: 1
+
+  rockchip,sfc-no-dma:
+    description: Disable DMA and utilize FIFO mode only
+    type: boolean
+
+patternProperties:
+  "^flash@[0-3]$":
+    type: object
+    properties:
+      reg:
+        minimum: 0
+        maximum: 3
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/px30-power.h>
+
+    sfc: spi@ff3a0000 {
+        compatible = "rockchip,sfc";
+        reg = <0xff3a0000 0x4000>;
+        interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+        clock-names = "clk_sfc", "hclk_sfc";
+        pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;
+        pinctrl-names = "default";
+        power-domains = <&power PX30_PD_MMC_NAND>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {
+            compatible = "jedec,spi-nor";
+            reg = <0>;
+            spi-max-frequency = <108000000>;
+            spi-rx-bus-width = <2>;
+            spi-tx-bus-width = <2>;
+        };
+    };
+
+...