[1/4] ARM: dts: am335x-boneblack: Extract HDMI config

Message ID 20210617093330.9179-2-paul.barker@sancloud.com
State Superseded
Headers show
Series
  • Add support for the SanCloud BBE Lite
Related show

Commit Message

Paul Barker June 17, 2021, 9:33 a.m.
Move the HDMI hardware configuration for the BeagleBone Black out of the
boneblack common dtsi file and into its own separate dtsi file. This
allows the devicetree for BeagleBone Black derivatives which lack the
hdmi encoding hardware to include the common dtsi file without needing
to duplicate configuration or override the status of all hdmi-related
nodes.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
---
 .../arm/boot/dts/am335x-boneblack-common.dtsi | 135 ------------------
 ...common.dtsi => am335x-boneblack-hdmi.dtsi} |  28 ----
 .../boot/dts/am335x-boneblack-wireless.dts    |   1 +
 arch/arm/boot/dts/am335x-boneblack.dts        |   1 +
 arch/arm/boot/dts/am335x-sancloud-bbe.dts     |   1 +
 5 files changed, 3 insertions(+), 163 deletions(-)
 copy arch/arm/boot/dts/{am335x-boneblack-common.dtsi => am335x-boneblack-hdmi.dtsi} (90%)

Patch

diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
index 64c3e9269f40..10494c4431b9 100644
--- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi
+++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
@@ -3,9 +3,6 @@ 
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
-#include <dt-bindings/display/tda998x.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
@@ -25,145 +22,13 @@  &mmc2 {
 	non-removable;
 };
 
-&am33xx_pinmux {
-	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-		>;
-	};
-
-	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
-		>;
-	};
-
-	mcasp0_pins: mcasp0_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a11.GPIO1_27 */
-		>;
-	};
-};
-
-&lcdc {
-	status = "okay";
-
-	/* If you want to get 24 bit RGB and 16 BGR mode instead of
-	 * current 16 bit RGB and 24 BGR modes, set the propety
-	 * below to "crossed" and uncomment the video-ports -property
-	 * in tda19988 node.
-	 */
-	blue-and-red-wiring = "straight";
-
-	port {
-		lcdc_0: endpoint@0 {
-			remote-endpoint = <&hdmi_0>;
-		};
-	};
-};
-
-&i2c0 {
-	tda19988: tda19988@70 {
-		compatible = "nxp,tda998x";
-		reg = <0x70>;
-		nxp,calib-gpios = <&gpio1 25 0>;
-		interrupts-extended = <&gpio1 25 IRQ_TYPE_LEVEL_LOW>;
-
-		pinctrl-names = "default", "off";
-		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
-		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
-		/* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
-		/* video-ports = <0x234501>; */
-
-		#sound-dai-cells = <0>;
-		audio-ports = <	TDA998x_I2S	0x03>;
-
-		ports {
-			port@0 {
-				hdmi_0: endpoint@0 {
-					remote-endpoint = <&lcdc_0>;
-				};
-			};
-		};
-	};
-};
-
 &rtc {
 	system-power-controller;
 };
 
-&mcasp0	{
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcasp0_pins>;
-	status = "okay";
-	op-mode = <0>;	/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-			0 0 1 0
-		>;
-	tx-num-evt = <32>;
-	rx-num-evt = <32>;
-};
-
 / {
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
-
-	clk_mcasp0_fixed: clk_mcasp0_fixed {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <24576000>;
-	};
-
-	clk_mcasp0: clk_mcasp0 {
-		#clock-cells = <0>;
-		compatible = "gpio-gate-clock";
-		clocks = <&clk_mcasp0_fixed>;
-		enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
-	};
-
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "TI BeagleBone Black";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink0_master>;
-		simple-audio-card,frame-master = <&dailink0_master>;
-
-		dailink0_master: simple-audio-card,cpu {
-			sound-dai = <&mcasp0>;
-			clocks = <&clk_mcasp0>;
-		};
-
-		simple-audio-card,codec {
-			sound-dai = <&tda19988>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-hdmi.dtsi
similarity index 90%
copy from arch/arm/boot/dts/am335x-boneblack-common.dtsi
copy to arch/arm/boot/dts/am335x-boneblack-hdmi.dtsi
index 64c3e9269f40..7cfddada9348 100644
--- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi
+++ b/arch/arm/boot/dts/am335x-boneblack-hdmi.dtsi
@@ -6,25 +6,6 @@ 
 #include <dt-bindings/display/tda998x.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-&ldo3_reg {
-	regulator-min-microvolt = <1800000>;
-	regulator-max-microvolt = <1800000>;
-	regulator-always-on;
-};
-
-&mmc1 {
-	vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
-	vmmc-supply = <&vmmcsd_fixed>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_pins>;
-	bus-width = <8>;
-	status = "okay";
-	non-removable;
-};
-
 &am33xx_pinmux {
 	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
 		pinctrl-single,pins = <
@@ -113,10 +94,6 @@  hdmi_0: endpoint@0 {
 	};
 };
 
-&rtc {
-	system-power-controller;
-};
-
 &mcasp0	{
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
@@ -132,11 +109,6 @@  &mcasp0	{
 };
 
 / {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x20000000>; /* 512 MB */
-	};
-
 	clk_mcasp0_fixed: clk_mcasp0_fixed {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
index 86cad9912906..2bec2287fefe 100644
--- a/arch/arm/boot/dts/am335x-boneblack-wireless.dts
+++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
@@ -7,6 +7,7 @@ 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index e2ee8b8c07bc..9312197316f0 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -7,6 +7,7 @@ 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
 
 / {
 	model = "TI AM335x BeagleBone Black";
diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts
index 275ba339adf4..c82295654bdd 100644
--- a/arch/arm/boot/dts/am335x-sancloud-bbe.dts
+++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts
@@ -7,6 +7,7 @@ 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {