@@ -7,6 +7,7 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
#include <dt-bindings/iio/qcom,spmi-adc7-pmr735b.h>
#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
@@ -272,6 +273,34 @@
status = "okay";
};
+&sdhc_1 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+
+ non-removable;
+ no-sd;
+ no-sdio;
+
+ vmmc-supply = <&vreg_l7b_2p9>;
+ vqmmc-supply = <&vreg_l19b_1p8>;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_on>;
+ pinctrl-1 = <&sdc2_off>;
+
+ vmmc-supply = <&vreg_l9c_2p9>;
+ vqmmc-supply = <&vreg_l6c_2p9>;
+
+ cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
+};
+
&uart5 {
status = "okay";
};
@@ -291,3 +320,45 @@
bias-pull-up;
};
};
+
+&sdc1_on {
+ clk {
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd {
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ rclk {
+ bias-pull-down;
+ };
+};
+
+&sdc2_on {
+ clk {
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd {
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data {
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sd-cd {
+ bias-pull-up;
+ };
+};
@@ -24,6 +24,11 @@
chosen { };
+ aliases {
+ mmc1 = &sdhc_1;
+ mmc2 = &sdhc_2;
+ };
+
clocks {
xo_board: xo-board {
compatible = "fixed-clock";
@@ -436,6 +441,60 @@
#mbox-cells = <2>;
};
+ sdhc_1: sdhci@7c4000 {
+ compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5";
+ status = "disabled";
+
+ reg = <0 0x007c4000 0 0x1000>,
+ <0 0x007c5000 0 0x1000>;
+ reg-names = "hc", "cqhci";
+
+ iommus = <&apps_smmu 0xc0 0x0>;
+ interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "core", "iface", "xo";
+ interconnects = <&aggre1_noc MASTER_SDCC_1 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_1 0>;
+ interconnect-names = "sdhc-ddr","cpu-sdhc";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
+
+ bus-width = <8>;
+ supports-cqe;
+
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+
+ sdhc1_opp_table: sdhc1-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ opp-peak-kBps = <1800000 400000>;
+ opp-avg-kBps = <100000 0>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ opp-peak-kBps = <5400000 1600000>;
+ opp-avg-kBps = <390000 0>;
+ };
+ };
+
+ };
+
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x2000>;
@@ -1035,6 +1094,51 @@
};
};
+ sdhc_2: sdhci@8804000 {
+ compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5";
+ status = "disabled";
+
+ reg = <0 0x08804000 0 0x1000>;
+
+ iommus = <&apps_smmu 0x100 0x0>;
+ interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+ <&gcc GCC_SDCC2_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "core", "iface", "xo";
+ interconnects = <&aggre1_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_2 0>;
+ interconnect-names = "sdhc-ddr","cpu-sdhc";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+
+ bus-width = <4>;
+
+ qcom,dll-config = <0x0007642c>;
+
+ sdhc2_opp_table: sdhc2-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ opp-peak-kBps = <1800000 400000>;
+ opp-avg-kBps = <100000 0>;
+ };
+
+ opp-202000000 {
+ opp-hz = /bits/ 64 <202000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ opp-peak-kBps = <5400000 1600000>;
+ opp-avg-kBps = <200000 0>;
+ };
+ };
+
+ };
+
dc_noc: interconnect@90e0000 {
reg = <0 0x090e0000 0 0x5080>;
compatible = "qcom,sc7280-dc-noc";
@@ -1185,6 +1289,87 @@
pins = "gpio46", "gpio47";
function = "qup13";
};
+
+ sdc1_on: sdc1-on {
+ clk {
+ pins = "sdc1_clk";
+ };
+
+ cmd {
+ pins = "sdc1_cmd";
+ };
+
+ data {
+ pins = "sdc1_data";
+ };
+
+ rclk {
+ pins = "sdc1_rclk";
+ };
+ };
+
+ sdc1_off: sdc1-off {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+
+ cmd {
+ pins = "sdc1_cmd";
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+
+ data {
+ pins = "sdc1_data";
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+
+ rclk {
+ pins = "sdc1_rclk";
+ bias-bus-hold;
+ };
+ };
+
+ sdc2_on: sdc2-on {
+ clk {
+ pins = "sdc2_clk";
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ };
+
+ data {
+ pins = "sdc2_data";
+ };
+
+ sd-cd {
+ pins = "gpio91";
+ };
+ };
+
+ sdc2_off: sdc2-off {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+
+ cmd {
+ pins ="sdc2_cmd";
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+
+ data {
+ pins ="sdc2_data";
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+ };
};
apps_smmu: iommu@15000000 {
Add nodes for eMMC and SD card on sc7280. Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org> --- This change is depends on the below patch series: https://lore.kernel.org/patchwork/cover/1418814/ Changes since V4: - Included gpio header in proper order and moved default pins configs to soc file as suggested by Stephen Boyd. Changes since V3: - Changed pinconfig names as suggested by Konrad Dybcio. - Removed extra lines and aligned some of lines as suggested by Bjorn Andersson. Change since V2: - Added leading zero's for register address and "qcom,sc7280-sdhci" string in compatible as suggested by Stephen Boyd and Doug. - Removed max-frequency flag, no-mmc and no-sdio flags for Sd card as suggested by Doug and Stephen Boyd. - Moved non-removable, no-sd, no-sdio and some pin config changes from soc to board dts file as suggested by Doug. - Removed sleep state for CD line and drive-strength for input pins as suggested by Doug. - Updated bus vote numbers for eMMC and SD card. Changes since V1: - Moved SDHC nodes as suggested by Bjorn Andersson. - Dropped "pinconf-" prefix as suggested by Bjorn Andersson. - Removed extra newlines as suggested by Konrad Dybcio. - Changed sd-cd pin to bias-pull-up in sdc2_off as suggested by Veerabhadrarao Badiganti. - Added bandwidth votes for eMMC and SD card. --- arch/arm64/boot/dts/qcom/sc7280-idp.dts | 71 ++++++++++++ arch/arm64/boot/dts/qcom/sc7280.dtsi | 185 ++++++++++++++++++++++++++++++++ 2 files changed, 256 insertions(+)