diff mbox

[v4,2/2] uart: pl011: Add support to ZTE ZX296702 uart

Message ID 1428390686-3225-2-git-send-email-jun.nie@linaro.org
State New
Headers show

Commit Message

Jun Nie April 7, 2015, 7:11 a.m. UTC
Support ZTE uart with some registers differing offset.
Probe as platform device for not AMBA IP ID is
available on ZTE uart.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
 drivers/tty/serial/Kconfig      |   4 +-
 drivers/tty/serial/amba-pl011.c | 225 +++++++++++++++++++++++++++++++++++++---
 include/linux/amba/serial.h     |  14 +++
 3 files changed, 227 insertions(+), 16 deletions(-)
diff mbox

Patch

diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index d2501f0..982ca78 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -47,12 +47,12 @@  config SERIAL_AMBA_PL010_CONSOLE
 
 config SERIAL_AMBA_PL011
 	tristate "ARM AMBA PL011 serial port support"
-	depends on ARM_AMBA
+	depends on ARM_AMBA || SOC_ZX296702
 	select SERIAL_CORE
 	help
 	  This selects the ARM(R) AMBA(R) PrimeCell PL011 UART.  If you have
 	  an Integrator/PP2, Integrator/CP or Versatile platform, say Y or M
-	  here.
+	  here. Say yes if you have SOC_ZX296702.
 
 	  If unsure, say N.
 
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 7c494f8..31ada19 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -74,6 +74,10 @@ 
 /* There is by now at least one vendor with differing details, so handle it */
 struct vendor_data {
 	unsigned int		ifls;
+	unsigned int		fr_busy;
+	unsigned int		fr_dsr;
+	unsigned int		fr_cts;
+	unsigned int		u1_fr_ri;
 	u8			*reg_lut;
 	bool			oversampling;
 	bool			dma_threshold;
@@ -82,13 +86,14 @@  struct vendor_data {
 	unsigned int (*get_fifosize)(struct amba_device *dev);
 };
 
+#ifdef CONFIG_ARM_AMBA
 static unsigned int get_fifosize_arm(struct amba_device *dev)
 {
 	return amba_rev(dev) < 3 ? 16 : 32;
 }
 
-static u8 arm_reg[] = {
-	/*  All registers offset are in order except [8]=0x2c */
+static u8 arm_reg[REG_NR] = {
+	/*  All registers offset are in order except LCRH as comment */
 	[IDX(UART01x_DR)]	= UART01x_DR,
 	[IDX(UART01x_RSR)]	= UART01x_RSR,
 	[IDX(ST_UART011_DMAWM)]	= ST_UART011_DMAWM,
@@ -112,6 +117,10 @@  static u8 arm_reg[] = {
 
 static struct vendor_data vendor_arm = {
 	.ifls			= UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
+	.fr_busy		= UART01x_FR_BUSY,
+	.fr_dsr			= UART01x_FR_DSR,
+	.fr_cts			= UART01x_FR_CTS,
+	.u1_fr_ri		= UART011_FR_RI,
 	.reg_lut		= arm_reg,
 	.oversampling		= false,
 	.dma_threshold		= false,
@@ -124,7 +133,7 @@  static unsigned int get_fifosize_st(struct amba_device *dev)
 	return 64;
 }
 
-static u8 st_reg[] = {
+static u8 st_reg[REG_NR] = {
 	/* All registers offset are in order */
 	[IDX(UART01x_DR)]	= UART01x_DR,
 	[IDX(UART01x_RSR)]	= UART01x_RSR,
@@ -149,12 +158,60 @@  static u8 st_reg[] = {
 
 static struct vendor_data vendor_st = {
 	.ifls			= UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF,
+	.fr_busy		= UART01x_FR_BUSY,
+	.fr_dsr			= UART01x_FR_DSR,
+	.fr_cts			= UART01x_FR_CTS,
+	.u1_fr_ri		= UART011_FR_RI,
 	.reg_lut		= st_reg,
 	.oversampling		= true,
 	.dma_threshold		= true,
 	.cts_event_workaround	= true,
 	.get_fifosize		= get_fifosize_st,
 };
+#endif
+
+#ifdef CONFIG_SOC_ZX296702
+static unsigned int get_fifosize_zx(struct amba_device *dev)
+{
+	return 16;
+}
+
+static u8 zx_reg[REG_NR] = {
+	/* Registers offset are remapped from origin offset as in comment */
+	[IDX(UART01x_DR)]	= ZX_UART01x_DR,	/* remapped */
+	[IDX(UART01x_RSR)]	= UART01x_RSR,
+	[IDX(ST_UART011_DMAWM)]	= ST_UART011_DMAWM,
+	[IDX(UART010_LCRM)]	= UART010_LCRM,
+	[IDX(UART010_LCRL)]	= UART010_LCRL,
+	[IDX(UART010_CR)]	= UART010_CR,
+	[IDX(UART01x_FR)]	= ZX_UART01x_FR,	/* remapped */
+	[IDX(UART011_LCRH_TX)]	= UART011_LCRH_RX,
+	[IDX(UART01x_ILPR)]	= UART01x_ILPR,
+	[IDX(UART011_IBRD)]	= UART011_IBRD,
+	[IDX(UART011_FBRD)]	= UART011_FBRD,
+	[IDX(UART011_LCRH_TX)]	= ZX_UART011_LCRH_TX,	/* remapped */
+	[IDX(UART011_CR)]	= ZX_UART011_CR,	/* remapped */
+	[IDX(UART011_IFLS)]	= ZX_UART011_IFLS,	/* remapped */
+	[IDX(UART011_IMSC)]	= ZX_UART011_IMSC,	/* remapped */
+	[IDX(UART011_RIS)]	= UART011_RIS,
+	[IDX(UART011_MIS)]	= ZX_UART011_MIS,	/* remapped */
+	[IDX(UART011_ICR)]	= ZX_UART011_ICR,	/* remapped */
+	[IDX(UART011_DMACR)]	= ZX_UART011_DMACR,	/* remapped */
+};
+
+static struct vendor_data vendor_zx = {
+	.ifls			= UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
+	.fr_busy		= ZX_UART01x_FR_BUSY,
+	.fr_dsr			= ZX_UART01x_FR_DSR,
+	.fr_cts			= ZX_UART01x_FR_CTS,
+	.u1_fr_ri		= ZX_UART011_FR_RI,
+	.reg_lut		= zx_reg,
+	.oversampling		= false,
+	.dma_threshold		= false,
+	.cts_event_workaround	= false,
+	.get_fifosize		= get_fifosize_zx,
+};
+#endif
 
 /* Deals with DMA transactions */
 
@@ -198,6 +255,10 @@  struct uart_amba_port {
 	unsigned int		im;		/* interrupt mask */
 	unsigned int		old_status;
 	unsigned int		fifosize;	/* vendor-specific */
+	unsigned int		fr_busy;        /* vendor-specific */
+	unsigned int		fr_dsr;		/* vendor-specific */
+	unsigned int		fr_cts;         /* vendor-specific */
+	unsigned int		u1_fr_ri;       /* vendor-specific */
 	unsigned int		old_cr;		/* state during shutdown */
 	bool			autorts;
 	char			type[12];
@@ -1160,7 +1221,7 @@  static void pl011_dma_shutdown(struct uart_amba_port *uap)
 		return;
 
 	/* Disable RX and TX DMA */
-	while (pl011_readw(uap, UART01x_FR) & UART01x_FR_BUSY)
+	while (pl011_readw(uap, UART01x_FR) & uap->fr_busy)
 		barrier();
 
 	spin_lock_irq(&uap->port.lock);
@@ -1387,11 +1448,11 @@  static void pl011_modem_status(struct uart_amba_port *uap)
 	if (delta & UART01x_FR_DCD)
 		uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
 
-	if (delta & UART01x_FR_DSR)
+	if (delta & uap->fr_dsr)
 		uap->port.icount.dsr++;
 
-	if (delta & UART01x_FR_CTS)
-		uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS);
+	if (delta & uap->fr_cts)
+		uart_handle_cts_change(&uap->port, status & uap->fr_cts);
 
 	wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
 }
@@ -1458,7 +1519,7 @@  static unsigned int pl011_tx_empty(struct uart_port *port)
 	    container_of(port, struct uart_amba_port, port);
 
 	unsigned int status = pl011_readw(uap, UART01x_FR);
-	return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
+	return status & (uap->fr_busy|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
 }
 
 static unsigned int pl011_get_mctrl(struct uart_port *port)
@@ -1473,9 +1534,9 @@  static unsigned int pl011_get_mctrl(struct uart_port *port)
 		result |= tiocmbit
 
 	TIOCMBIT(UART01x_FR_DCD, TIOCM_CAR);
-	TIOCMBIT(UART01x_FR_DSR, TIOCM_DSR);
-	TIOCMBIT(UART01x_FR_CTS, TIOCM_CTS);
-	TIOCMBIT(UART011_FR_RI, TIOCM_RNG);
+	TIOCMBIT(uap->fr_dsr, TIOCM_DSR);
+	TIOCMBIT(uap->fr_cts, TIOCM_CTS);
+	TIOCMBIT(uap->u1_fr_ri, TIOCM_RNG);
 #undef TIOCMBIT
 	return result;
 }
@@ -1678,7 +1739,7 @@  static int pl011_startup(struct uart_port *port)
 	pl011_writew(uap, 1, UART011_IBRD);
 	pl011_write_lcr_h(uap, 0);
 	pl011_writew(uap, 0, UART01x_DR);
-	while (pl011_readw(uap, UART01x_FR) & UART01x_FR_BUSY)
+	while (pl011_readw(uap, UART01x_FR) & uap->fr_busy)
 		barrier();
 
 	pl011_writew(uap, fbrd, UART011_FBRD);
@@ -2023,6 +2084,9 @@  static struct uart_amba_port *amba_ports[UART_NR];
 
 static void pl011_console_putchar(struct uart_port *port, int ch)
 {
+	struct uart_amba_port *uap =
+	    container_of(port, struct uart_amba_port, port);
+
 	while (pl011_readw(uap, UART01x_FR) & UART01x_FR_TXFF)
 		barrier();
 	pl011_writew(uap, ch, UART01x_DR);
@@ -2062,7 +2126,7 @@  pl011_console_write(struct console *co, const char *s, unsigned int count)
 	 */
 	do {
 		status = pl011_readw(uap, UART01x_FR);
-	} while (status & UART01x_FR_BUSY);
+	} while (status & uap->fr_busy);
 	pl011_writew(uap, old_cr, UART011_CR);
 
 	if (locked)
@@ -2173,7 +2237,7 @@  static void pl011_putc(struct uart_port *port, int c)
 	while (pl011_readw(uap, UART01x_FR) & UART01x_FR_TXFF)
 		;
 	pl011_writeb(uap, c, UART01x_DR);
-	while (pl011_readw(uap, UART01x_FR) & UART01x_FR_BUSY)
+	while (pl011_readw(uap, UART01x_FR) & uap->fr_busy)
 		;
 }
 
@@ -2210,6 +2274,7 @@  static struct uart_driver amba_reg = {
 	.cons			= AMBA_CONSOLE,
 };
 
+#ifdef CONFIG_ARM_AMBA
 static int pl011_probe_dt_alias(int index, struct device *dev)
 {
 	struct device_node *np;
@@ -2274,6 +2339,10 @@  static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
 
 	uap->reg_lut = vendor->reg_lut;
 	uap->vendor = vendor;
+	uap->fr_busy = vendor->fr_busy;
+	uap->fr_dsr = vendor->fr_dsr;
+	uap->fr_cts = vendor->fr_cts;
+	uap->u1_fr_ri = vendor->u1_fr_ri;
 	uap->old_cr = 0;
 	uap->fifosize = vendor->get_fifosize(dev);
 	uap->port.dev = &dev->dev;
@@ -2334,6 +2403,101 @@  static int pl011_remove(struct amba_device *dev)
 		uart_unregister_driver(&amba_reg);
 	return 0;
 }
+#endif
+
+#ifdef CONFIG_SOC_ZX296702
+static int zx_uart_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct uart_amba_port *uap;
+	struct vendor_data *vendor = &vendor_zx;
+	struct resource *res;
+	void __iomem *base;
+	int i, ret;
+
+	uap = devm_kzalloc(&pdev->dev, sizeof(struct uart_amba_port),
+			GFP_KERNEL);
+	if (uap == NULL) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	i = of_alias_get_id(np, "serial");
+	if (i < 0) {
+		dev_err(&pdev->dev, "failed to get alias id: %d\n", i);
+		ret = i;
+		goto out;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (!base) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	uap->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(uap->clk)) {
+		ret = PTR_ERR(uap->clk);
+		goto out;
+	}
+
+	uap->reg_lut = vendor->reg_lut;
+	uap->vendor = vendor;
+	uap->fr_busy = vendor->fr_busy;
+	uap->fr_dsr = vendor->fr_dsr;
+	uap->fr_cts = vendor->fr_cts;
+	uap->u1_fr_ri = vendor->u1_fr_ri;
+	uap->old_cr = 0;
+	uap->fifosize = 16;
+	uap->port.dev = &pdev->dev;
+	uap->port.mapbase = res->start;
+	uap->port.membase = base;
+	uap->port.iotype = UPIO_MEM;
+	uap->port.irq = platform_get_irq(pdev, 0);
+	uap->port.fifosize = uap->fifosize;
+	uap->port.ops = &amba_pl011_pops;
+	uap->port.flags = UPF_BOOT_AUTOCONF;
+	uap->port.line = i;
+	uap->port.uartclk = clk_get_rate(uap->clk);
+	pl011_dma_probe(&pdev->dev, uap);
+
+	/* Ensure interrupts from this UART are masked and cleared */
+	pl011_writew(uap, 0, UART011_IMSC);
+	pl011_writew(uap, 0xffff, UART011_ICR);
+
+	amba_ports[i] = uap;
+
+	platform_set_drvdata(pdev, uap);
+	ret = uart_register_driver(&amba_reg);
+	if (ret < 0) {
+		pr_err("Failed to register AMBA-PL011 driver\n");
+		return ret;
+	}
+	ret = uart_add_one_port(&amba_reg, &uap->port);
+	if (ret) {
+		amba_ports[i] = NULL;
+		pl011_dma_remove(uap);
+	}
+out:
+	return ret;
+}
+
+static int zx_uart_remove(struct platform_device *pdev)
+{
+	struct uart_amba_port *uap = platform_get_drvdata(pdev);
+	int i;
+
+	uart_remove_one_port(&amba_reg, &uap->port);
+
+	for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
+		if (amba_ports[i] == uap)
+			amba_ports[i] = NULL;
+
+	pl011_dma_remove(uap);
+	return 0;
+}
+#endif
 
 #ifdef CONFIG_PM_SLEEP
 static int pl011_suspend(struct device *dev)
@@ -2359,6 +2523,7 @@  static int pl011_resume(struct device *dev)
 
 static SIMPLE_DEV_PM_OPS(pl011_dev_pm_ops, pl011_suspend, pl011_resume);
 
+#ifdef CONFIG_ARM_AMBA
 static struct amba_id pl011_ids[] = {
 	{
 		.id	= 0x00041011,
@@ -2385,16 +2550,48 @@  static struct amba_driver pl011_driver = {
 	.remove		= pl011_remove,
 };
 
+#endif
+
+#ifdef CONFIG_SOC_ZX296702
+static const struct of_device_id zx_uart_dt_ids[] = {
+	{ .compatible = "zte,zx296702-uart", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, zx_uart_dt_ids);
+
+static struct platform_driver zx_uart_driver = {
+	.driver = {
+		.name	= "zx-uart",
+		.owner	= THIS_MODULE,
+		.pm	= &pl011_dev_pm_ops,
+		.of_match_table = zx_uart_dt_ids,
+	},
+	.probe		= zx_uart_probe,
+	.remove		= zx_uart_remove,
+};
+#endif
+
 static int __init pl011_init(void)
 {
 	printk(KERN_INFO "Serial: AMBA PL011 UART driver\n");
 
+#ifdef CONFIG_ARM_AMBA
 	return amba_driver_register(&pl011_driver);
+#endif
+
+#ifdef CONFIG_SOC_ZX296702
+	return platform_driver_register(&zx_uart_driver);
+#endif
 }
 
 static void __exit pl011_exit(void)
 {
+#ifdef CONFIG_ARM_AMBA
 	amba_driver_unregister(&pl011_driver);
+#endif
+#ifdef CONFIG_SOC_ZX296702
+	platform_driver_unregister(&zx_uart_driver);
+#endif
 }
 
 /*
diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h
index 1fe1549..84f2330 100644
--- a/include/linux/amba/serial.h
+++ b/include/linux/amba/serial.h
@@ -31,6 +31,7 @@ 
  *  UART Register Offsets.
  */
 #define UART01x_DR		0x00	/* Data read or written from the interface. */
+#define ZX_UART01x_DR		0x04	/* Data read or written from the interface. */
 #define UART01x_RSR		0x04	/* Receive status register (Read). */
 #define UART01x_ECR		0x04	/* Error clear register (Write). */
 #define UART010_LCRH		0x08	/* Line control register, high byte. */
@@ -39,6 +40,7 @@ 
 #define ST_UART011_TIMEOUT	0x0C    /* Timeout period register. */
 #define UART010_LCRL		0x10	/* Line control register, low byte. */
 #define UART010_CR		0x14	/* Control register. */
+#define ZX_UART01x_FR		0x14	/* Flag register (Read only). */
 #define UART01x_FR		0x18	/* Flag register (Read only). */
 #define UART010_IIR		0x1C	/* Interrupt identification register (Read). */
 #define UART010_ICR		0x1C	/* Interrupt clear register (Write). */
@@ -50,14 +52,22 @@ 
 #define UART011_LCRH		0x2c	/* Line control register. */
 #define UART011_LCRH_TX		0x2c	/* Line control register. */
 #define ST_UART011_LCRH_TX	0x2c    /* Tx Line control register. */
+#define ZX_UART011_LCRH_TX	0x30    /* Tx Line control register. */
 #define UART011_CR		0x30	/* Control register. */
 #define UART011_IFLS		0x34	/* Interrupt fifo level select. */
+#define ZX_UART011_CR		0x34	/* Control register. */
+#define ZX_UART011_IFLS		0x38	/* Interrupt fifo level select. */
 #define UART011_IMSC		0x38	/* Interrupt mask. */
 #define UART011_RIS		0x3c	/* Raw interrupt status. */
+#define ZX_UART011_IMSC		0x40	/* Interrupt mask. */
 #define UART011_MIS		0x40	/* Masked interrupt status. */
+#define ZX_UART011_RIS		0x44	/* Raw interrupt status. */
 #define UART011_ICR		0x44	/* Interrupt clear register. */
 #define UART011_DMACR		0x48	/* DMA control register. */
+#define ZX_UART011_MIS		0x48	/* Masked interrupt status. */
+#define ZX_UART011_ICR		0x4c	/* Interrupt clear register. */
 #define ST_UART011_XFCR		0x50	/* XON/XOFF control register. */
+#define ZX_UART011_DMACR	0x50	/* DMA control register. */
 #define ST_UART011_XON1		0x54	/* XON1 register. */
 #define ST_UART011_XON2		0x58	/* XON2 register. */
 #define ST_UART011_XOFF1	0x5C	/* XON1 register. */
@@ -79,15 +89,19 @@ 
 
 #define UART011_FR_TXBUSY       0x100
 #define UART011_FR_RXBUSY       0x200
+#define ZX_UART01x_FR_BUSY         (UART011_FR_RXBUSY | UART011_FR_TXBUSY)
 #define UART011_FR_RI		0x100
 #define UART011_FR_TXFE		0x080
 #define UART011_FR_RXFF		0x040
 #define UART01x_FR_TXFF		0x020
 #define UART01x_FR_RXFE		0x010
 #define UART01x_FR_BUSY		0x008
+#define ZX_UART01x_FR_DSR       0x008
 #define UART01x_FR_DCD 		0x004
 #define UART01x_FR_DSR 		0x002
+#define ZX_UART01x_FR_CTS          0x002
 #define UART01x_FR_CTS 		0x001
+#define ZX_UART011_FR_RI           0x001
 #define UART01x_FR_TMSK		(UART01x_FR_TXFF + UART01x_FR_BUSY)
 
 #define UART011_CR_CTSEN	0x8000	/* CTS hardware flow control */