@@ -45,6 +45,7 @@ static unsigned int fmax = 515633;
* struct variant_data - MMCI variant-specific quirks
* @clkreg: default value for MCICLOCK register
* @clkreg_enable: enable value for MMCICLOCK register
+ * @dma_sdio_req_ctrl: enable value for DMAREQCTL register for SDIO write
* @datalength_bits: number of bits in the MMCIDATALENGTH register
* @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
* is asserted (likewise for RX)
@@ -58,6 +59,7 @@ static unsigned int fmax = 515633;
struct variant_data {
unsigned int clkreg;
unsigned int clkreg_enable;
+ unsigned int dma_sdio_req_ctrl;
unsigned int datalength_bits;
unsigned int fifosize;
unsigned int fifohalfsize;
@@ -92,6 +94,7 @@ static struct variant_data variant_ux500 = {
.fifohalfsize = 8 * 4,
.clkreg = MCI_CLK_ENABLE,
.clkreg_enable = MCI_ST_UX500_HWFCEN,
+ .dma_sdio_req_ctrl = MCI_ST_DPSM_DMAREQCTL,
.datalength_bits = 24,
.sdio = true,
.st_clkdiv = true,
@@ -102,6 +105,7 @@ static struct variant_data variant_ux500v2 = {
.fifohalfsize = 8 * 4,
.clkreg = MCI_CLK_ENABLE,
.clkreg_enable = MCI_ST_UX500_HWFCEN,
+ .dma_sdio_req_ctrl = MCI_ST_DPSM_DMAREQCTL,
.datalength_bits = 24,
.sdio = true,
.st_clkdiv = true,
@@ -110,6 +114,31 @@ static struct variant_data variant_ux500v2 = {
};
/*
+ * Validate mmc prerequisites
+ */
+static int mmci_validate_data(struct mmci_host *host,
+ struct mmc_data *data)
+{
+ if (!data)
+ return 0;
+
+ if (!host->variant->non_power_of_2_blksize &&
+ !is_power_of_2(data->blksz)) {
+ dev_err(mmc_dev(host->mmc),
+ "unsupported block size (%d bytes)\n", data->blksz);
+ return -EINVAL;
+ }
+
+ if (data->sg->offset & 3) {
+ dev_err(mmc_dev(host->mmc),
+ "unsupported alginment (0x%x)\n", data->sg->offset);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
* This must be called with host->lock held
*/
static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
@@ -401,8 +430,12 @@ static int mmci_dma_prep_data(struct mmci_host *host, struct mmc_data *data,
if (!chan)
return -EINVAL;
- /* If less than or equal to the fifo size, don't bother with DMA */
- if (data->blksz * data->blocks <= variant->fifosize)
+ /*
+ * If less than or equal to the fifo size, don't bother with DMA
+ * SDIO transfers may not be 4 bytes aligned, fall back to PIO
+ */
+ if (data->blksz * data->blocks <= variant->fifosize ||
+ (data->blksz * data->blocks) & 3)
return -EINVAL;
device = chan->device;
@@ -437,6 +470,7 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
{
int ret;
struct mmc_data *data = host->data;
+ struct variant_data *variant = host->variant;
ret = mmci_dma_prep_data(host, host->data, NULL);
if (ret)
@@ -451,6 +485,11 @@ static int mmci_dma_start_data(struct mmci_host *host, unsigned int datactrl)
datactrl |= MCI_DPSM_DMAENABLE;
+ /* Some hardware versions need special flags for SDIO DMA write */
+ if (variant->sdio && host->mmc->card && mmc_card_sdio(host->mmc->card)
+ && (data->flags & MMC_DATA_WRITE))
+ datactrl |= variant->dma_sdio_req_ctrl;
+
/* Trigger the DMA transfer */
writel(datactrl, host->base + MMCIDATACTRL);
@@ -495,6 +534,9 @@ static void mmci_pre_request(struct mmc_host *mmc, struct mmc_request *mrq,
if (!data)
return;
+ if (mmci_validate_data(host, mrq->data))
+ return;
+
if (data->host_cookie) {
data->host_cookie = 0;
return;
@@ -976,17 +1018,12 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
{
struct mmci_host *host = mmc_priv(mmc);
- struct variant_data *variant = host->variant;
unsigned long flags;
WARN_ON(host->mrq != NULL);
- if (mrq->data &&
- !variant->non_power_of_2_blksize &&
- !is_power_of_2(mrq->data->blksz)) {
- dev_err(mmc_dev(mmc), "unsupported block size (%d bytes)\n",
- mrq->data->blksz);
- mrq->cmd->error = -EINVAL;
+ mrq->cmd->error = mmci_validate_data(host, mrq->data);
+ if (mrq->cmd->error) {
mmc_request_done(mmc, mrq);
return;
}
@@ -70,6 +70,13 @@
#define MCI_ST_DPSM_RWMOD (1 << 10)
#define MCI_ST_DPSM_SDIOEN (1 << 11)
/* Control register extensions in the ST Micro Ux500 versions */
+/*
+ * DMA request control is required for write
+ * if transfer size is not 32 byte aligned.
+ * DMA request control is also needed if the total
+ * transfer size is 32 byte aligned but any of the
+ * sg element lengths are not aligned with 32 byte.
+ */
#define MCI_ST_DPSM_DMAREQCTL (1 << 12)
#define MCI_ST_DPSM_DBOOTMODEEN (1 << 13)
#define MCI_ST_DPSM_BUSYMODE (1 << 14)