diff mbox series

[PATCHv1,3/3] net: stmmac: dwmac-meson8b: Add reset controller for ethernet phy

Message ID 20210729201100.3994-4-linux.amoon@gmail.com
State New
Headers show
Series [PATCHv1,1/3] arm64: dts: amlogic: add missing ethernet reset ID | expand

Commit Message

Anand Moon July 29, 2021, 8:10 p.m. UTC
Add reset controller for Ethernet phy reset on every boot for
Amlogic SoC.

Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
 .../ethernet/stmicro/stmmac/dwmac-meson8b.c   | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

Comments

Martin Blumenstingl Aug. 3, 2021, 8:45 p.m. UTC | #1
Hi Anand,

On Thu, Jul 29, 2021 at 10:11 PM Anand Moon <linux.amoon@gmail.com> wrote:
>
> Add reset controller for Ethernet phy reset on every boot for
> Amlogic SoC.
I think this description does not match what's going on inside the SoC:
- for all SoCs earlier than GXL the PHY is external so the reset for
the PHY is a GPIO
- the reset line you are passing in the .dts belongs to the Ethernet
controller on SoCs earlier than GXL
- I *believe* that the rset line which you're passing in the .dts
belongs to the Ethernet controller AND the built-in MDIO mux on GXL
and newer, see also [0]
- from how the PRG_ETH registers work I doubt that these are connected
to a reset line (as they're managing mostly delays and protocol - so I
don't see what would be reset). This is speculation though.


Best regards,
Martin


[0] https://lore.kernel.org/linux-amlogic/553e127c-9839-d15b-d435-c01f18c7be48@gmail.com/
diff mbox series

Patch

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index c7a6588d9398..8b3b5e8c2a8a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -17,6 +17,7 @@ 
 #include <linux/of_net.h>
 #include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
+#include <linux/reset.h>
 #include <linux/stmmac.h>
 
 #include "stmmac_platform.h"
@@ -95,6 +96,7 @@  struct meson8b_dwmac {
 	u32				tx_delay_ns;
 	u32				rx_delay_ps;
 	struct clk			*timing_adj_clk;
+	struct reset_control		*eth_reset;
 };
 
 struct meson8b_dwmac_clk_configs {
@@ -384,6 +386,17 @@  static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
 	meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TX_AND_PHY_REF_CLK,
 				PRG_ETH0_TX_AND_PHY_REF_CLK);
 
+	/* Make sure the Ethernet PHY is properly reseted, as U-Boot may leave
+	 * it at deasserted state, and thus it may fail to reset EMAC.
+	 *
+	 * This assumes the driver has exclusive access to the EPHY reset.
+	 */
+	ret = reset_control_reset(dwmac->eth_reset);
+	if (ret) {
+		dev_err(dwmac->dev, "Cannot reset internal PHY\n");
+		return ret;
+	}
+
 	return 0;
 }
 
@@ -465,6 +478,13 @@  static int meson8b_dwmac_probe(struct platform_device *pdev)
 		goto err_remove_config_dt;
 	}
 
+	dwmac->eth_reset = devm_reset_control_get_exclusive(dwmac->dev, "ethreset");
+	if (IS_ERR_OR_NULL(dwmac->eth_reset)) {
+		dev_err(dwmac->dev, "Failed to get Ethernet reset\n");
+		ret = PTR_ERR(dwmac->eth_reset);
+		goto err_remove_config_dt;
+	}
+
 	ret = meson8b_init_rgmii_delays(dwmac);
 	if (ret)
 		goto err_remove_config_dt;