| Message ID | 20210827202722.2567687-2-vladimir.oltean@nxp.com |
|---|---|
| State | New |
| Headers | show |
| Series | [devicetree,1/2] dt-bindings: arm: fsl: document the LX2160A BlueBox 3 boards | expand |
On Fri, Aug 27, 2021 at 3:28 PM Vladimir Oltean <vladimir.oltean@nxp.com> wrote: > > From: Wasim Khan <wasim.khan@nxp.com> > > The NXP BlueBox3 is a prototyping board for high-performance autonomous > driving systems. It contains two Linux systems, on running on the > LX2160A and the other on the S32G2 SoC. This patch adds the device tree > support for the LX2160A SoC. > > In terms of networking from the LX2160A's perspective, there are: > > - 4 RJ45 10G ports using Aquantia copper PHYs which are attached > directly to DPAA2 ports on the LX2160A > > - 3 NXP SJA1110 automotive Ethernet switches. First two are managed by > the LX2160A (each switch has a host port towards a dpmac), the third > switch is managed by the S32G2. All 3 switches are interconnected > through on-board SERDES lanes. The cascade ports between the 2 > switches managed by LX2160A form a DSA link, the cascade ports between > the LX2160A and the S32G2 domain form user ports (the "to_sw3" net > device). > > - 2 RJ45 1G ports using Atheros copper PHYs which are attached directly > to NXP SJA1110 switches > > - 12 automotive 100base-T1 single-pair Ethernet ports routed from the > SJA1110 internal PHY ports (TJA1103) > > - One SGMII SERDES lane towards an internal connector, attached to one > of the SJA1110 switch ports > > On board rev A, the AR8035 RGMII PHY addresses were different than on > rev B and later. This patch introduces a separate device tree for rev A. > The main device tree is supposed to cover rev B and later. > > Signed-off-by: Wasim Khan <wasim.khan@nxp.com> > Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com> > Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> > Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com> > Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> > Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> > Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> > Co-developed-by: Biwen Li <biwen.li@nxp.com> > Signed-off-by: Biwen Li <biwen.li@nxp.com> > Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com> > Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com> > Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com> > Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> > Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com> > Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> > --- > arch/arm64/boot/dts/freescale/Makefile | 2 + > .../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 + > .../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++ > 3 files changed, 694 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts > create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index db9e36ebe932..ecf74464705f 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb > +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts > new file mode 100644 > index 000000000000..15d273c93154 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts > @@ -0,0 +1,34 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +// > +// Device Tree file for LX2160A BLUEBOX3 > +// > +// Copyright 2020-2021 NXP > + > +/dts-v1/; > + > +#include "fsl-lx2160a-bluebox3.dts" > + > +/ { > + compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a"; > +}; > + > +/* The RGMII PHYs have a different MDIO address */ > +&emdio1 { > + /delete-node/ ethernet-phy@5; > + > + sw1_mii3_phy: ethernet-phy@1 { > + /* AR8035 */ > + compatible = "ethernet-phy-id004d.d072"; > + reg = <0x1>; > + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>; > + }; > + > + /delete-node/ ethernet-phy@6; > + > + sw2_mii3_phy: ethernet-phy@2 { > + /* AR8035 */ > + compatible = "ethernet-phy-id004d.d072"; > + reg = <0x2>; > + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts > new file mode 100644 > index 000000000000..be7d01630a6f > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts > @@ -0,0 +1,658 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +// > +// Device Tree file for LX2160A BLUEBOX3 > +// > +// Copyright 2020-2021 NXP > + > +/dts-v1/; > + > +#include "fsl-lx2160a.dtsi" > + > +/ { > + model = "NXP Layerscape LX2160ABLUEBOX3"; > + compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a"; > + > + aliases { > + crypto = &crypto; > + serial0 = &uart0; > + mmc0 = &esdhc0; > + mmc1 = &esdhc1; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + sb_3v3: regulator-sb3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "MC34717-3.3VSB"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > +}; > + > +&can0 { > + status = "okay"; > + > + can-transceiver { > + max-bitrate = <5000000>; > + }; > +}; > + > +&can1 { > + status = "okay"; > + > + can-transceiver { > + max-bitrate = <5000000>; > + }; > +}; > + > +&crypto { > + status = "okay"; > +}; > + > +&dpmac5 { > + phy-handle = <&aqr113c_phy1>; > + phy-mode = "usxgmii"; > + managed = "in-band-status"; > +}; > + > +&dpmac6 { > + phy-handle = <&aqr113c_phy2>; > + phy-mode = "usxgmii"; > + managed = "in-band-status"; > +}; > + > +&dpmac9 { > + phy-handle = <&aqr113c_phy3>; > + phy-mode = "usxgmii"; > + managed = "in-band-status"; > +}; > + > +&dpmac10 { > + phy-handle = <&aqr113c_phy4>; > + phy-mode = "usxgmii"; > + managed = "in-band-status"; > +}; > + > +&dpmac17 { > + phy-mode = "rgmii"; > + status = "okay"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > +}; > + > +&dpmac18 { > + phy-mode = "rgmii"; > + status = "okay"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > +}; > + > +&emdio1 { > + status = "okay"; > + > + aqr113c_phy2: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x0>; > + /* IRQ_10G_PHY2 */ > + interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>; > + }; > + > + aqr113c_phy1: ethernet-phy@8 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x8>; > + /* IRQ_10G_PHY1 */ > + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>; > + }; > + > + sw1_mii3_phy: ethernet-phy@5 { > + /* AR8035 */ > + compatible = "ethernet-phy-id004d.d072"; > + reg = <0x5>; > + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>; > + }; > + > + sw2_mii3_phy: ethernet-phy@6 { > + /* AR8035 */ > + compatible = "ethernet-phy-id004d.d072"; > + reg = <0x6>; > + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > + > +&emdio2 { > + status = "okay"; > + > + aqr113c_phy4: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x0>; > + /* IRQ_10G_PHY4 */ > + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>; > + }; > + > + aqr113c_phy3: ethernet-phy@8 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x8>; > + /* IRQ_10G_PHY3 */ > + interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > + > +&esdhc0 { > + sd-uhs-sdr104; > + sd-uhs-sdr50; > + sd-uhs-sdr25; > + sd-uhs-sdr12; > + status = "okay"; > +}; > + > +&esdhc1 { > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > + bus-width = <8>; > + status = "okay"; > +}; > + > +&fspi { > + status = "okay"; > + > + mt35xu512aba0: flash@0 { > + compatible = "jedec,spi-nor"; > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0>; > + m25p,fast-read; > + spi-max-frequency = <50000000>; > + spi-rx-bus-width = <8>; > + spi-tx-bus-width = <8>; > + }; > + > + mt35xu512aba1: flash@1 { > + compatible = "jedec,spi-nor"; > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <1>; > + m25p,fast-read; > + spi-max-frequency = <50000000>; > + spi-rx-bus-width = <8>; > + spi-tx-bus-width = <8>; > + }; > +}; > + > +&i2c0 { > + status = "okay"; > + > + i2c-mux@77 { > + compatible = "nxp,pca9547"; > + reg = <0x77>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c@2 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x2>; > + > + power-monitor@40 { > + compatible = "ti,ina220"; > + reg = <0x40>; > + shunt-resistor = <500>; > + }; > + }; > + > + i2c@3 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x3>; > + > + temp2: temperature-sensor@48 { > + compatible = "nxp,sa56004"; > + reg = <0x48>; > + vcc-supply = <&sb_3v3>; > + #thermal-sensor-cells = <1>; > + }; > + > + temp1: temperature-sensor@4c { > + compatible = "nxp,sa56004"; > + reg = <0x4c>; > + vcc-supply = <&sb_3v3>; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + i2c@4 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x4>; > + > + rtc@51 { > + compatible = "nxp,pcf2129"; > + reg = <0x51>; > + interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>; > + }; > + }; > + > + i2c@7 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x7>; > + > + i2c-mux@75 { > + compatible = "nxp,pca9547"; > + reg = <0x75>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x0>; > + > + spi_bridge: spi@28 { > + compatible = "nxp,sc18is602b"; > + reg = <0x28>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > + }; > + }; > + }; > +}; > + > +&i2c5 { > + status = "okay"; > + > + i2c-mux@77 { > + compatible = "nxp,pca9846"; > + reg = <0x77>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x1>; > + > + /* The I2C multiplexer and temperature sensors are on > + * the T6 riser card. > + */ > + i2c-mux@70 { > + compatible = "nxp,pca9548"; > + reg = <0x70>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c@6 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x6>; > + > + q12: temperature-sensor@4c { > + compatible = "nxp,sa56004"; > + reg = <0x4c>; > + vcc-supply = <&sb_3v3>; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + i2c@7 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x7>; > + > + q11: temperature-sensor@4c { > + compatible = "nxp,sa56004"; > + reg = <0x4c>; > + vcc-supply = <&sb_3v3>; > + #thermal-sensor-cells = <1>; > + }; > + > + q13: temperature-sensor@48 { > + compatible = "nxp,sa56004"; > + reg = <0x48>; > + vcc-supply = <&sb_3v3>; > + #thermal-sensor-cells = <1>; > + }; > + > + q14: temperature-sensor@4a { > + compatible = "nxp,sa56004"; > + reg = <0x4a>; > + vcc-supply = <&sb_3v3>; > + #thermal-sensor-cells = <1>; > + }; > + }; > + }; > + }; > + }; > +}; > + > +&pcs_mdio5 { > + status = "okay"; > +}; > + > +&pcs_mdio6 { > + status = "okay"; > +}; > + > +&pcs_mdio9 { > + status = "okay"; > +}; > + > +&pcs_mdio10 { > + status = "okay"; > +}; > + > +&spi_bridge { > + sw1: ethernet-switch@0 { > + compatible = "nxp,sja1110a"; > + reg = <0>; > + spi-max-frequency = <4000000>; > + spi-cpol; > + dsa,member = <0 0>; > + > + ethernet-ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* Microcontroller port */ > + port@0 { > + reg = <0>; > + status = "disabled"; > + }; > + > + /* SW1_P1 */ > + port@1 { > + reg = <1>; > + label = "con_2x20"; > + phy-mode = "sgmii"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > + }; > + > + port@2 { > + reg = <2>; > + ethernet = <&dpmac17>; > + phy-mode = "rgmii-id"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > + }; > + > + port@3 { > + reg = <3>; > + label = "1ge_p1"; > + phy-mode = "rgmii-id"; > + phy-handle = <&sw1_mii3_phy>; > + }; > + > + sw1p4: port@4 { > + reg = <4>; > + link = <&sw2p1>; > + phy-mode = "sgmii"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > + }; > + > + port@5 { > + reg = <5>; > + label = "trx1"; > + phy-mode = "internal"; > + phy-handle = <&sw1_port5_base_t1_phy>; > + }; > + > + port@6 { > + reg = <6>; > + label = "trx2"; > + phy-mode = "internal"; > + phy-handle = <&sw1_port6_base_t1_phy>; > + }; > + > + port@7 { > + reg = <7>; > + label = "trx3"; > + phy-mode = "internal"; > + phy-handle = <&sw1_port7_base_t1_phy>; > + }; > + > + port@8 { > + reg = <8>; > + label = "trx4"; > + phy-mode = "internal"; > + phy-handle = <&sw1_port8_base_t1_phy>; > + }; > + > + port@9 { > + reg = <9>; > + label = "trx5"; > + phy-mode = "internal"; > + phy-handle = <&sw1_port9_base_t1_phy>; > + }; > + > + port@a { > + reg = <10>; > + label = "trx6"; > + phy-mode = "internal"; > + phy-handle = <&sw1_port10_base_t1_phy>; > + }; > + }; > + > + mdios { > + #address-cells = <1>; > + #size-cells = <0>; > + > + mdio@0 { > + compatible = "nxp,sja1110-base-t1-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + sw1_port5_base_t1_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x1>; > + }; > + > + sw1_port6_base_t1_phy: ethernet-phy@2 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x2>; > + }; > + > + sw1_port7_base_t1_phy: ethernet-phy@3 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x3>; > + }; > + > + sw1_port8_base_t1_phy: ethernet-phy@4 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x4>; > + }; > + > + sw1_port9_base_t1_phy: ethernet-phy@5 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x5>; > + }; > + > + sw1_port10_base_t1_phy: ethernet-phy@6 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x6>; > + }; > + }; > + }; > + }; > + > + sw2: ethernet-switch@2 { > + compatible = "nxp,sja1110a"; > + reg = <2>; > + spi-max-frequency = <4000000>; > + spi-cpol; > + dsa,member = <0 1>; > + > + ethernet-ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* Microcontroller port */ > + port@0 { > + reg = <0>; > + status = "disabled"; > + }; > + > + sw2p1: port@1 { > + reg = <1>; > + link = <&sw1p4>; > + phy-mode = "sgmii"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > + }; > + > + port@2 { > + reg = <2>; > + ethernet = <&dpmac18>; > + phy-mode = "rgmii-id"; > + > + fixed-link { > + speed = <1000>; > + full-duplex; > + }; > + }; > + > + port@3 { > + reg = <3>; > + label = "1ge_p2"; > + phy-mode = "rgmii-id"; > + phy-handle = <&sw2_mii3_phy>; > + }; > + > + port@4 { > + reg = <4>; > + label = "to_sw3"; > + phy-mode = "2500base-x"; > + > + fixed-link { > + speed = <2500>; > + full-duplex; > + }; > + }; > + > + port@5 { > + reg = <5>; > + label = "trx7"; > + phy-mode = "internal"; > + phy-handle = <&sw2_port5_base_t1_phy>; > + }; > + > + port@6 { > + reg = <6>; > + label = "trx8"; > + phy-mode = "internal"; > + phy-handle = <&sw2_port6_base_t1_phy>; > + }; > + > + port@7 { > + reg = <7>; > + label = "trx9"; > + phy-mode = "internal"; > + phy-handle = <&sw2_port7_base_t1_phy>; > + }; > + > + port@8 { > + reg = <8>; > + label = "trx10"; > + phy-mode = "internal"; > + phy-handle = <&sw2_port8_base_t1_phy>; > + }; > + > + port@9 { > + reg = <9>; > + label = "trx11"; > + phy-mode = "internal"; > + phy-handle = <&sw2_port9_base_t1_phy>; > + }; > + > + port@a { > + reg = <10>; > + label = "trx12"; > + phy-mode = "internal"; > + phy-handle = <&sw2_port10_base_t1_phy>; > + }; > + }; > + > + mdios { > + #address-cells = <1>; > + #size-cells = <0>; > + > + mdio@0 { > + compatible = "nxp,sja1110-base-t1-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + sw2_port5_base_t1_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x1>; > + }; > + > + sw2_port6_base_t1_phy: ethernet-phy@2 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x2>; > + }; > + > + sw2_port7_base_t1_phy: ethernet-phy@3 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x3>; > + }; > + > + sw2_port8_base_t1_phy: ethernet-phy@4 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x4>; > + }; > + > + sw2_port9_base_t1_phy: ethernet-phy@5 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x5>; > + }; > + > + sw2_port10_base_t1_phy: ethernet-phy@6 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x6>; > + }; > + }; > + }; > + }; > +}; > + > +&uart0 { > + status = "okay"; > +}; > + > +&uart1 { > + status = "okay"; > +}; > + > +&usb0 { > + status = "okay"; > +}; > + > +&usb1 { > + status = "okay"; > +}; > -- > 2.25.1 >
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index db9e36ebe932..ecf74464705f 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts new file mode 100644 index 000000000000..15d273c93154 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Device Tree file for LX2160A BLUEBOX3 +// +// Copyright 2020-2021 NXP + +/dts-v1/; + +#include "fsl-lx2160a-bluebox3.dts" + +/ { + compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a"; +}; + +/* The RGMII PHYs have a different MDIO address */ +&emdio1 { + /delete-node/ ethernet-phy@5; + + sw1_mii3_phy: ethernet-phy@1 { + /* AR8035 */ + compatible = "ethernet-phy-id004d.d072"; + reg = <0x1>; + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>; + }; + + /delete-node/ ethernet-phy@6; + + sw2_mii3_phy: ethernet-phy@2 { + /* AR8035 */ + compatible = "ethernet-phy-id004d.d072"; + reg = <0x2>; + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts new file mode 100644 index 000000000000..be7d01630a6f --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts @@ -0,0 +1,658 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Device Tree file for LX2160A BLUEBOX3 +// +// Copyright 2020-2021 NXP + +/dts-v1/; + +#include "fsl-lx2160a.dtsi" + +/ { + model = "NXP Layerscape LX2160ABLUEBOX3"; + compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a"; + + aliases { + crypto = &crypto; + serial0 = &uart0; + mmc0 = &esdhc0; + mmc1 = &esdhc1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + sb_3v3: regulator-sb3v3 { + compatible = "regulator-fixed"; + regulator-name = "MC34717-3.3VSB"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&can0 { + status = "okay"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; + +&can1 { + status = "okay"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; + +&crypto { + status = "okay"; +}; + +&dpmac5 { + phy-handle = <&aqr113c_phy1>; + phy-mode = "usxgmii"; + managed = "in-band-status"; +}; + +&dpmac6 { + phy-handle = <&aqr113c_phy2>; + phy-mode = "usxgmii"; + managed = "in-band-status"; +}; + +&dpmac9 { + phy-handle = <&aqr113c_phy3>; + phy-mode = "usxgmii"; + managed = "in-band-status"; +}; + +&dpmac10 { + phy-handle = <&aqr113c_phy4>; + phy-mode = "usxgmii"; + managed = "in-band-status"; +}; + +&dpmac17 { + phy-mode = "rgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&dpmac18 { + phy-mode = "rgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&emdio1 { + status = "okay"; + + aqr113c_phy2: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x0>; + /* IRQ_10G_PHY2 */ + interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>; + }; + + aqr113c_phy1: ethernet-phy@8 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x8>; + /* IRQ_10G_PHY1 */ + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>; + }; + + sw1_mii3_phy: ethernet-phy@5 { + /* AR8035 */ + compatible = "ethernet-phy-id004d.d072"; + reg = <0x5>; + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>; + }; + + sw2_mii3_phy: ethernet-phy@6 { + /* AR8035 */ + compatible = "ethernet-phy-id004d.d072"; + reg = <0x6>; + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&emdio2 { + status = "okay"; + + aqr113c_phy4: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x0>; + /* IRQ_10G_PHY4 */ + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>; + }; + + aqr113c_phy3: ethernet-phy@8 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x8>; + /* IRQ_10G_PHY3 */ + interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&esdhc0 { + sd-uhs-sdr104; + sd-uhs-sdr50; + sd-uhs-sdr25; + sd-uhs-sdr12; + status = "okay"; +}; + +&esdhc1 { + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; + status = "okay"; +}; + +&fspi { + status = "okay"; + + mt35xu512aba0: flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + m25p,fast-read; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <8>; + spi-tx-bus-width = <8>; + }; + + mt35xu512aba1: flash@1 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <1>; + m25p,fast-read; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <8>; + spi-tx-bus-width = <8>; + }; +}; + +&i2c0 { + status = "okay"; + + i2c-mux@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + + power-monitor@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <500>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + temp2: temperature-sensor@48 { + compatible = "nxp,sa56004"; + reg = <0x48>; + vcc-supply = <&sb_3v3>; + #thermal-sensor-cells = <1>; + }; + + temp1: temperature-sensor@4c { + compatible = "nxp,sa56004"; + reg = <0x4c>; + vcc-supply = <&sb_3v3>; + #thermal-sensor-cells = <1>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4>; + + rtc@51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>; + }; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x7>; + + i2c-mux@75 { + compatible = "nxp,pca9547"; + reg = <0x75>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + + spi_bridge: spi@28 { + compatible = "nxp,sc18is602b"; + reg = <0x28>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; + }; + }; +}; + +&i2c5 { + status = "okay"; + + i2c-mux@77 { + compatible = "nxp,pca9846"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + + /* The I2C multiplexer and temperature sensors are on + * the T6 riser card. + */ + i2c-mux@70 { + compatible = "nxp,pca9548"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6>; + + q12: temperature-sensor@4c { + compatible = "nxp,sa56004"; + reg = <0x4c>; + vcc-supply = <&sb_3v3>; + #thermal-sensor-cells = <1>; + }; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x7>; + + q11: temperature-sensor@4c { + compatible = "nxp,sa56004"; + reg = <0x4c>; + vcc-supply = <&sb_3v3>; + #thermal-sensor-cells = <1>; + }; + + q13: temperature-sensor@48 { + compatible = "nxp,sa56004"; + reg = <0x48>; + vcc-supply = <&sb_3v3>; + #thermal-sensor-cells = <1>; + }; + + q14: temperature-sensor@4a { + compatible = "nxp,sa56004"; + reg = <0x4a>; + vcc-supply = <&sb_3v3>; + #thermal-sensor-cells = <1>; + }; + }; + }; + }; + }; +}; + +&pcs_mdio5 { + status = "okay"; +}; + +&pcs_mdio6 { + status = "okay"; +}; + +&pcs_mdio9 { + status = "okay"; +}; + +&pcs_mdio10 { + status = "okay"; +}; + +&spi_bridge { + sw1: ethernet-switch@0 { + compatible = "nxp,sja1110a"; + reg = <0>; + spi-max-frequency = <4000000>; + spi-cpol; + dsa,member = <0 0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Microcontroller port */ + port@0 { + reg = <0>; + status = "disabled"; + }; + + /* SW1_P1 */ + port@1 { + reg = <1>; + label = "con_2x20"; + phy-mode = "sgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@2 { + reg = <2>; + ethernet = <&dpmac17>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@3 { + reg = <3>; + label = "1ge_p1"; + phy-mode = "rgmii-id"; + phy-handle = <&sw1_mii3_phy>; + }; + + sw1p4: port@4 { + reg = <4>; + link = <&sw2p1>; + phy-mode = "sgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@5 { + reg = <5>; + label = "trx1"; + phy-mode = "internal"; + phy-handle = <&sw1_port5_base_t1_phy>; + }; + + port@6 { + reg = <6>; + label = "trx2"; + phy-mode = "internal"; + phy-handle = <&sw1_port6_base_t1_phy>; + }; + + port@7 { + reg = <7>; + label = "trx3"; + phy-mode = "internal"; + phy-handle = <&sw1_port7_base_t1_phy>; + }; + + port@8 { + reg = <8>; + label = "trx4"; + phy-mode = "internal"; + phy-handle = <&sw1_port8_base_t1_phy>; + }; + + port@9 { + reg = <9>; + label = "trx5"; + phy-mode = "internal"; + phy-handle = <&sw1_port9_base_t1_phy>; + }; + + port@a { + reg = <10>; + label = "trx6"; + phy-mode = "internal"; + phy-handle = <&sw1_port10_base_t1_phy>; + }; + }; + + mdios { + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + compatible = "nxp,sja1110-base-t1-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + sw1_port5_base_t1_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x1>; + }; + + sw1_port6_base_t1_phy: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x2>; + }; + + sw1_port7_base_t1_phy: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x3>; + }; + + sw1_port8_base_t1_phy: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x4>; + }; + + sw1_port9_base_t1_phy: ethernet-phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x5>; + }; + + sw1_port10_base_t1_phy: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x6>; + }; + }; + }; + }; + + sw2: ethernet-switch@2 { + compatible = "nxp,sja1110a"; + reg = <2>; + spi-max-frequency = <4000000>; + spi-cpol; + dsa,member = <0 1>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Microcontroller port */ + port@0 { + reg = <0>; + status = "disabled"; + }; + + sw2p1: port@1 { + reg = <1>; + link = <&sw1p4>; + phy-mode = "sgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@2 { + reg = <2>; + ethernet = <&dpmac18>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@3 { + reg = <3>; + label = "1ge_p2"; + phy-mode = "rgmii-id"; + phy-handle = <&sw2_mii3_phy>; + }; + + port@4 { + reg = <4>; + label = "to_sw3"; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + + port@5 { + reg = <5>; + label = "trx7"; + phy-mode = "internal"; + phy-handle = <&sw2_port5_base_t1_phy>; + }; + + port@6 { + reg = <6>; + label = "trx8"; + phy-mode = "internal"; + phy-handle = <&sw2_port6_base_t1_phy>; + }; + + port@7 { + reg = <7>; + label = "trx9"; + phy-mode = "internal"; + phy-handle = <&sw2_port7_base_t1_phy>; + }; + + port@8 { + reg = <8>; + label = "trx10"; + phy-mode = "internal"; + phy-handle = <&sw2_port8_base_t1_phy>; + }; + + port@9 { + reg = <9>; + label = "trx11"; + phy-mode = "internal"; + phy-handle = <&sw2_port9_base_t1_phy>; + }; + + port@a { + reg = <10>; + label = "trx12"; + phy-mode = "internal"; + phy-handle = <&sw2_port10_base_t1_phy>; + }; + }; + + mdios { + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + compatible = "nxp,sja1110-base-t1-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + sw2_port5_base_t1_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x1>; + }; + + sw2_port6_base_t1_phy: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x2>; + }; + + sw2_port7_base_t1_phy: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x3>; + }; + + sw2_port8_base_t1_phy: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x4>; + }; + + sw2_port9_base_t1_phy: ethernet-phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x5>; + }; + + sw2_port10_base_t1_phy: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x6>; + }; + }; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +};