@@ -20602,6 +20602,12 @@ F: drivers/misc/Makefile
F: drivers/misc/xilinx_sdfec.c
F: include/uapi/misc/xilinx_sdfec.h
+XILINX TIMER/PWM DRIVER
+M: Sean Anderson <sean.anderson@seco.com>
+S: Maintained
+F: drivers/clocksource/timer-xilinx*
+F: include/clocksource/timer-xilinx.h
+
XILINX UARTLITE SERIAL DRIVER
M: Peter Korsgaard <jacmet@sunsite.dk>
L: linux-serial@vger.kernel.org
@@ -5,7 +5,6 @@
ifdef CONFIG_FUNCTION_TRACER
# Do not trace early boot code and low level code
-CFLAGS_REMOVE_timer.o = -pg
CFLAGS_REMOVE_intc.o = -pg
CFLAGS_REMOVE_early_printk.o = -pg
CFLAGS_REMOVE_ftrace.o = -pg
@@ -17,7 +16,7 @@ extra-y := head.o vmlinux.lds
obj-y += dma.o exceptions.o \
hw_exception_handler.o irq.o \
process.o prom.o ptrace.o \
- reset.o setup.o signal.o sys_microblaze.o timer.o traps.o unwind.o
+ reset.o setup.o signal.o sys_microblaze.o traps.o unwind.o
obj-y += cpu/
deleted file mode 100644
@@ -1,326 +0,0 @@
-/*
- * Copyright (C) 2007-2013 Michal Simek <monstr@monstr.eu>
- * Copyright (C) 2012-2013 Xilinx, Inc.
- * Copyright (C) 2007-2009 PetaLogix
- * Copyright (C) 2006 Atmark Techno, Inc.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/sched.h>
-#include <linux/sched/clock.h>
-#include <linux/sched_clock.h>
-#include <linux/clk.h>
-#include <linux/clockchips.h>
-#include <linux/of_address.h>
-#include <linux/of_irq.h>
-#include <linux/timecounter.h>
-#include <asm/cpuinfo.h>
-
-static void __iomem *timer_baseaddr;
-
-static unsigned int freq_div_hz;
-static unsigned int timer_clock_freq;
-
-#define TCSR0 (0x00)
-#define TLR0 (0x04)
-#define TCR0 (0x08)
-#define TCSR1 (0x10)
-#define TLR1 (0x14)
-#define TCR1 (0x18)
-
-#define TCSR_MDT (1<<0)
-#define TCSR_UDT (1<<1)
-#define TCSR_GENT (1<<2)
-#define TCSR_CAPT (1<<3)
-#define TCSR_ARHT (1<<4)
-#define TCSR_LOAD (1<<5)
-#define TCSR_ENIT (1<<6)
-#define TCSR_ENT (1<<7)
-#define TCSR_TINT (1<<8)
-#define TCSR_PWMA (1<<9)
-#define TCSR_ENALL (1<<10)
-
-static unsigned int (*read_fn)(void __iomem *);
-static void (*write_fn)(u32, void __iomem *);
-
-static void timer_write32(u32 val, void __iomem *addr)
-{
- iowrite32(val, addr);
-}
-
-static unsigned int timer_read32(void __iomem *addr)
-{
- return ioread32(addr);
-}
-
-static void timer_write32_be(u32 val, void __iomem *addr)
-{
- iowrite32be(val, addr);
-}
-
-static unsigned int timer_read32_be(void __iomem *addr)
-{
- return ioread32be(addr);
-}
-
-static inline void xilinx_timer0_stop(void)
-{
- write_fn(read_fn(timer_baseaddr + TCSR0) & ~TCSR_ENT,
- timer_baseaddr + TCSR0);
-}
-
-static inline void xilinx_timer0_start_periodic(unsigned long load_val)
-{
- if (!load_val)
- load_val = 1;
- /* loading value to timer reg */
- write_fn(load_val, timer_baseaddr + TLR0);
-
- /* load the initial value */
- write_fn(TCSR_LOAD, timer_baseaddr + TCSR0);
-
- /* see timer data sheet for detail
- * !ENALL - don't enable 'em all
- * !PWMA - disable pwm
- * TINT - clear interrupt status
- * ENT- enable timer itself
- * ENIT - enable interrupt
- * !LOAD - clear the bit to let go
- * ARHT - auto reload
- * !CAPT - no external trigger
- * !GENT - no external signal
- * UDT - set the timer as down counter
- * !MDT0 - generate mode
- */
- write_fn(TCSR_TINT|TCSR_ENIT|TCSR_ENT|TCSR_ARHT|TCSR_UDT,
- timer_baseaddr + TCSR0);
-}
-
-static inline void xilinx_timer0_start_oneshot(unsigned long load_val)
-{
- if (!load_val)
- load_val = 1;
- /* loading value to timer reg */
- write_fn(load_val, timer_baseaddr + TLR0);
-
- /* load the initial value */
- write_fn(TCSR_LOAD, timer_baseaddr + TCSR0);
-
- write_fn(TCSR_TINT|TCSR_ENIT|TCSR_ENT|TCSR_ARHT|TCSR_UDT,
- timer_baseaddr + TCSR0);
-}
-
-static int xilinx_timer_set_next_event(unsigned long delta,
- struct clock_event_device *dev)
-{
- pr_debug("%s: next event, delta %x\n", __func__, (u32)delta);
- xilinx_timer0_start_oneshot(delta);
- return 0;
-}
-
-static int xilinx_timer_shutdown(struct clock_event_device *evt)
-{
- pr_info("%s\n", __func__);
- xilinx_timer0_stop();
- return 0;
-}
-
-static int xilinx_timer_set_periodic(struct clock_event_device *evt)
-{
- pr_info("%s\n", __func__);
- xilinx_timer0_start_periodic(freq_div_hz);
- return 0;
-}
-
-static struct clock_event_device clockevent_xilinx_timer = {
- .name = "xilinx_clockevent",
- .features = CLOCK_EVT_FEAT_ONESHOT |
- CLOCK_EVT_FEAT_PERIODIC,
- .shift = 8,
- .rating = 300,
- .set_next_event = xilinx_timer_set_next_event,
- .set_state_shutdown = xilinx_timer_shutdown,
- .set_state_periodic = xilinx_timer_set_periodic,
-};
-
-static inline void timer_ack(void)
-{
- write_fn(read_fn(timer_baseaddr + TCSR0), timer_baseaddr + TCSR0);
-}
-
-static irqreturn_t timer_interrupt(int irq, void *dev_id)
-{
- struct clock_event_device *evt = &clockevent_xilinx_timer;
- timer_ack();
- evt->event_handler(evt);
- return IRQ_HANDLED;
-}
-
-static __init int xilinx_clockevent_init(void)
-{
- clockevent_xilinx_timer.mult =
- div_sc(timer_clock_freq, NSEC_PER_SEC,
- clockevent_xilinx_timer.shift);
- clockevent_xilinx_timer.max_delta_ns =
- clockevent_delta2ns((u32)~0, &clockevent_xilinx_timer);
- clockevent_xilinx_timer.max_delta_ticks = (u32)~0;
- clockevent_xilinx_timer.min_delta_ns =
- clockevent_delta2ns(1, &clockevent_xilinx_timer);
- clockevent_xilinx_timer.min_delta_ticks = 1;
- clockevent_xilinx_timer.cpumask = cpumask_of(0);
- clockevents_register_device(&clockevent_xilinx_timer);
-
- return 0;
-}
-
-static u64 xilinx_clock_read(void)
-{
- return read_fn(timer_baseaddr + TCR1);
-}
-
-static u64 xilinx_read(struct clocksource *cs)
-{
- /* reading actual value of timer 1 */
- return (u64)xilinx_clock_read();
-}
-
-static struct timecounter xilinx_tc = {
- .cc = NULL,
-};
-
-static u64 xilinx_cc_read(const struct cyclecounter *cc)
-{
- return xilinx_read(NULL);
-}
-
-static struct cyclecounter xilinx_cc = {
- .read = xilinx_cc_read,
- .mask = CLOCKSOURCE_MASK(32),
- .shift = 8,
-};
-
-static int __init init_xilinx_timecounter(void)
-{
- xilinx_cc.mult = div_sc(timer_clock_freq, NSEC_PER_SEC,
- xilinx_cc.shift);
-
- timecounter_init(&xilinx_tc, &xilinx_cc, sched_clock());
-
- return 0;
-}
-
-static struct clocksource clocksource_microblaze = {
- .name = "xilinx_clocksource",
- .rating = 300,
- .read = xilinx_read,
- .mask = CLOCKSOURCE_MASK(32),
- .flags = CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static int __init xilinx_clocksource_init(void)
-{
- int ret;
-
- ret = clocksource_register_hz(&clocksource_microblaze,
- timer_clock_freq);
- if (ret) {
- pr_err("failed to register clocksource");
- return ret;
- }
-
- /* stop timer1 */
- write_fn(read_fn(timer_baseaddr + TCSR1) & ~TCSR_ENT,
- timer_baseaddr + TCSR1);
- /* start timer1 - up counting without interrupt */
- write_fn(TCSR_TINT|TCSR_ENT|TCSR_ARHT, timer_baseaddr + TCSR1);
-
- /* register timecounter - for ftrace support */
- return init_xilinx_timecounter();
-}
-
-static int __init xilinx_timer_init(struct device_node *timer)
-{
- struct clk *clk;
- static int initialized;
- u32 irq;
- u32 timer_num = 1;
- int ret;
-
- if (initialized)
- return -EINVAL;
-
- initialized = 1;
-
- timer_baseaddr = of_iomap(timer, 0);
- if (!timer_baseaddr) {
- pr_err("ERROR: invalid timer base address\n");
- return -ENXIO;
- }
-
- write_fn = timer_write32;
- read_fn = timer_read32;
-
- write_fn(TCSR_MDT, timer_baseaddr + TCSR0);
- if (!(read_fn(timer_baseaddr + TCSR0) & TCSR_MDT)) {
- write_fn = timer_write32_be;
- read_fn = timer_read32_be;
- }
-
- irq = irq_of_parse_and_map(timer, 0);
- if (irq <= 0) {
- pr_err("Failed to parse and map irq");
- return -EINVAL;
- }
-
- of_property_read_u32(timer, "xlnx,one-timer-only", &timer_num);
- if (timer_num) {
- pr_err("Please enable two timers in HW\n");
- return -EINVAL;
- }
-
- pr_info("%pOF: irq=%d\n", timer, irq);
-
- clk = of_clk_get(timer, 0);
- if (IS_ERR(clk)) {
- pr_err("ERROR: timer CCF input clock not found\n");
- /* If there is clock-frequency property than use it */
- of_property_read_u32(timer, "clock-frequency",
- &timer_clock_freq);
- } else {
- timer_clock_freq = clk_get_rate(clk);
- }
-
- if (!timer_clock_freq) {
- pr_err("ERROR: Using CPU clock frequency\n");
- timer_clock_freq = cpuinfo.cpu_clock_freq;
- }
-
- freq_div_hz = timer_clock_freq / HZ;
-
- ret = request_irq(irq, timer_interrupt, IRQF_TIMER, "timer",
- &clockevent_xilinx_timer);
- if (ret) {
- pr_err("Failed to setup IRQ");
- return ret;
- }
-
- ret = xilinx_clocksource_init();
- if (ret)
- return ret;
-
- ret = xilinx_clockevent_init();
- if (ret)
- return ret;
-
- sched_clock_register(xilinx_clock_read, 32, timer_clock_freq);
-
- return 0;
-}
-
-TIMER_OF_DECLARE(xilinx_timer, "xlnx,xps-timer-1.00.a",
- xilinx_timer_init);
@@ -708,4 +708,17 @@ config MICROCHIP_PIT64B
modes and high resolution. It is used as a clocksource
and a clockevent.
+config XILINX_TIMER
+ bool "Xilinx AXI Timer support"
+ depends on OF_ADDRESS
+ depends on COMMON_CLK
+ select REGMAP_MMIO
+ default y if MICROBLAZE
+ help
+ Clocksource/clockevent driver for Xilinx LogiCORE IP AXI
+ timers. This timer is typically a soft core which may be
+ present in Xilinx FPGAs. This device may also be present in
+ Microblaze soft processors. If you don't have this IP in your
+ design, choose N.
+
endmenu
@@ -88,3 +88,4 @@ obj-$(CONFIG_CSKY_MP_TIMER) += timer-mp-csky.o
obj-$(CONFIG_GX6605S_TIMER) += timer-gx6605s.o
obj-$(CONFIG_HYPERV_TIMER) += hyperv_timer.o
obj-$(CONFIG_MICROCHIP_PIT64B) += timer-microchip-pit64b.o
+obj-$(CONFIG_XILINX_TIMER) += timer-xilinx.o timer-xilinx-common.o
new file mode 100644
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 Sean Anderson <sean.anderson@seco.com>
+ *
+ * For Xilinx LogiCORE IP AXI Timer documentation, refer to DS764:
+ * https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf
+ */
+
+#include <clocksource/timer-xilinx.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+
+u32 xilinx_timer_tlr_cycles(struct xilinx_timer_priv *priv, u32 tcsr,
+ u64 cycles)
+{
+ WARN_ON(cycles < 2 || cycles - 2 > priv->max);
+
+ if (tcsr & TCSR_UDT)
+ return cycles - 2;
+ else
+ return priv->max - cycles + 2;
+}
+EXPORT_SYMBOL_GPL(xilinx_timer_tlr_cycles);
+
+unsigned int xilinx_timer_get_period(struct xilinx_timer_priv *priv,
+ u32 tlr, u32 tcsr)
+{
+ u64 cycles;
+
+ if (tcsr & TCSR_UDT)
+ cycles = tlr + 2;
+ else
+ cycles = (u64)priv->max - tlr + 2;
+
+ /* cycles has a max of 2^32 + 2 */
+ return DIV64_U64_ROUND_CLOSEST(cycles * NSEC_PER_SEC,
+ clk_get_rate(priv->clk));
+}
+EXPORT_SYMBOL_GPL(xilinx_timer_get_period);
+
+int xilinx_timer_common_init(struct device_node *np,
+ struct xilinx_timer_priv *priv,
+ u32 *one_timer)
+{
+ int ret;
+ u32 width;
+
+ ret = of_property_read_u32(np, "xlnx,one-timer-only", one_timer);
+ if (ret) {
+ pr_err("%pOF: err %d: xlnx,one-timer-only\n", np, ret);
+ return ret;
+ } else if (*one_timer && *one_timer != 1) {
+ pr_err("%pOF: xlnx,one-timer-only must be 0 or 1\n", np);
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32(np, "xlnx,count-width", &width);
+ if (ret == -EINVAL) {
+ width = 32;
+ } else if (ret) {
+ pr_err("%pOF: err %d: xlnx,count-width\n", np, ret);
+ return ret;
+ } else if (width < 8 || width > 32) {
+ pr_err("%pOF: invalid counter width\n", np);
+ return -EINVAL;
+ }
+ priv->max = BIT_ULL(width) - 1;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(xilinx_timer_common_init);
new file mode 100644
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 Sean Anderson <sean.anderson@seco.com>
+ *
+ * Limitations:
+ * - When in cascade mode we cannot read the full 64-bit counter in one go
+ */
+
+#include <clocksource/timer-xilinx.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/log2.h>
+#include <linux/interrupt.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
+#include <linux/sched_clock.h>
+#if IS_ENABLED(CONFIG_MICROBLAZE)
+#include <asm/cpuinfo.h>
+#endif
+
+struct xilinx_clocksource_device {
+ struct clocksource cs;
+ struct xilinx_timer_priv priv;
+};
+
+static inline struct xilinx_timer_priv
+*xilinx_clocksource_to_priv(struct clocksource *cs)
+{
+ return &container_of(cs, struct xilinx_clocksource_device, cs)->priv;
+}
+
+static u64 xilinx_clocksource_read(struct clocksource *cs)
+{
+ struct xilinx_timer_priv *priv = xilinx_clocksource_to_priv(cs);
+ unsigned int ret;
+
+ regmap_read(priv->map, TCR0, &ret);
+ return ret;
+}
+
+static struct xilinx_clocksource_device xilinx_clocksource = {
+ .cs = {
+ .name = "xilinx_clocksource",
+ .rating = 300,
+ .read = xilinx_clocksource_read,
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+ .owner = THIS_MODULE,
+ },
+};
+
+static u64 xilinx_sched_read(void)
+{
+ return xilinx_clocksource_read(&xilinx_clocksource.cs);
+}
+
+static int __init xilinx_clocksource_init(struct device_node *np)
+{
+ int ret;
+ struct xilinx_timer_priv *priv = &xilinx_clocksource.priv;
+ static const struct reg_sequence init[] = {
+ REG_SEQ0(TLR0, 0),
+ REG_SEQ0(TCSR0, TCSR_LOAD | TCSR_TINT),
+ REG_SEQ0(TCSR0, TCSR_ARHT | TCSR_ENT),
+ };
+
+ ret = regmap_multi_reg_write(priv->map, init, ARRAY_SIZE(init));
+ if (ret)
+ return ret;
+
+ xilinx_clocksource.cs.mask = priv->max;
+ ret = clocksource_register_hz(&xilinx_clocksource.cs,
+ clk_get_rate(priv->clk));
+ if (!ret)
+ sched_clock_register(xilinx_sched_read,
+ ilog2((u64)priv->max + 1),
+ clk_get_rate(priv->clk));
+ else
+ pr_err("%pOF: err %d: could not register clocksource\n",
+ np, ret);
+ return ret;
+}
+
+struct xilinx_clockevent_device {
+ struct clock_event_device ce;
+ struct xilinx_timer_priv priv;
+};
+
+static inline struct xilinx_timer_priv
+*xilinx_clockevent_to_priv(struct clock_event_device *ce)
+{
+ return &container_of(ce, struct xilinx_clockevent_device, ce)->priv;
+}
+
+static irqreturn_t xilinx_timer_handler(int irq, void *p)
+{
+ struct xilinx_clockevent_device *dev = p;
+
+ if (regmap_test_bits(dev->priv.map, TCSR0, TCSR_TINT) <= 0)
+ return IRQ_NONE;
+
+ regmap_clear_bits(dev->priv.map, TCSR0, TCSR_TINT);
+ dev->ce.event_handler(&dev->ce);
+ return IRQ_HANDLED;
+}
+
+static int xilinx_clockevent_next_event(unsigned long evt,
+ struct clock_event_device *ce)
+{
+ struct xilinx_timer_priv *priv = xilinx_clockevent_to_priv(ce);
+ struct reg_sequence next[] = {
+ REG_SEQ0(TLR0, evt - 2),
+ REG_SEQ0(TCSR0, TCSR_LOAD),
+ REG_SEQ0(TCSR0, TCSR_ENIT | TCSR_ENT),
+ };
+
+ return regmap_multi_reg_write(priv->map, next, ARRAY_SIZE(next));
+}
+
+static int xilinx_clockevent_state_periodic(struct clock_event_device *ce)
+{
+ struct xilinx_timer_priv *priv = xilinx_clockevent_to_priv(ce);
+ struct reg_sequence periodic[] = {
+ REG_SEQ0(TLR0, 0),
+ REG_SEQ0(TCSR0, TCSR_LOAD),
+ REG_SEQ0(TCSR0, TCSR_ARHT | TCSR_ENIT | TCSR_ENT),
+ };
+ unsigned long cycles = clk_get_rate(priv->clk) / HZ;
+
+ if (cycles < 2 || cycles - 2 > priv->max)
+ return -ERANGE;
+ periodic[0].def = xilinx_timer_tlr_cycles(priv, 0, cycles);
+
+ return regmap_multi_reg_write(priv->map, periodic, ARRAY_SIZE(periodic));
+}
+
+static int xilinx_clockevent_shutdown(struct clock_event_device *ce)
+{
+ struct xilinx_timer_priv *priv = xilinx_clockevent_to_priv(ce);
+
+ return regmap_write(priv->map, TCSR0, 0);
+}
+
+static const struct clock_event_device xilinx_clockevent_base __initconst = {
+ .rating = 300,
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .set_next_event = xilinx_clockevent_next_event,
+ .set_state_periodic = xilinx_clockevent_state_periodic,
+ .set_state_shutdown = xilinx_clockevent_shutdown,
+ .cpumask = cpu_possible_mask,
+ .owner = THIS_MODULE,
+};
+
+static int __init xilinx_clockevent_init(struct device_node *np,
+ struct xilinx_clockevent_device *dev)
+{
+ int irq, ret;
+
+ irq = ret = of_irq_get(np, 0);
+ if (ret < 0) {
+ pr_err("%pOF: err %d: could not get irq\n", np, ret);
+ return ret;
+ }
+
+ ret = request_irq(irq, xilinx_timer_handler, IRQF_TIMER,
+ of_node_full_name(np), dev);
+ if (ret) {
+ pr_err("%pOF: err %d: could not request irq\n", np, ret);
+ return ret;
+ }
+
+ memcpy(&dev->ce, &xilinx_clockevent_base, sizeof(dev->ce));
+ dev->ce.name = of_node_full_name(np);
+ clockevents_config_and_register(&dev->ce, clk_get_rate(dev->priv.clk), 2,
+ min_t(u64, (u64)dev->priv.max + 2,
+ ULONG_MAX));
+ return 0;
+}
+
+static const struct regmap_config xilinx_timer_regmap_config __initconst = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+ .max_register = TCR0,
+};
+
+static bool clocksource_uninitialized __initdata = true;
+
+static int __init xilinx_timer_init(struct device_node *np)
+{
+ bool artificial_clock = false;
+ int ret;
+ struct xilinx_timer_priv *priv;
+ struct xilinx_clockevent_device *dev;
+ u32 one_timer;
+ void __iomem *regs;
+
+ if (of_property_read_bool(np, "#pwm-cells"))
+ return 0;
+
+ regs = of_iomap(np, 0);
+ if (IS_ERR(regs)) {
+ ret = PTR_ERR(regs);
+ pr_err("%pOF: err %d: failed to map regs\n", np, ret);
+ return ret;
+ }
+
+ if (clocksource_uninitialized) {
+ priv = &xilinx_clocksource.priv;
+ } else {
+ dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ if (!dev) {
+ ret = -ENOMEM;
+ goto err_regs;
+ }
+ priv = &dev->priv;
+ }
+
+ priv->map = regmap_init_mmio(NULL, regs, &xilinx_timer_regmap_config);
+ if (IS_ERR(priv->map)) {
+ ret = PTR_ERR(priv->map);
+ goto err_priv;
+ }
+
+ ret = xilinx_timer_common_init(np, priv, &one_timer);
+ if (ret)
+ goto err_regmap;
+
+ priv->clk = of_clk_get_by_name(np, "s_axi_aclk");
+ if (IS_ERR(priv->clk)) {
+ u32 freq;
+
+ ret = PTR_ERR(priv->clk);
+ if (ret == -EPROBE_DEFER)
+ goto err_regs;
+
+ pr_warn("%pOF: missing s_axi_aclk, falling back to clock-frequency\n",
+ np);
+ ret = of_property_read_u32(np, "clock-frequency", &freq);
+ if (ret) {
+#if IS_ENABLED(CONFIG_MICROBLAZE)
+ pr_warn("%pOF: missing clock-frequency, falling back to /cpus/timebase-frequency\n",
+ np);
+ freq = cpuinfo.cpu_clock_freq;
+#else
+ goto err_regmap;
+#endif
+ }
+
+ priv->clk = clk_register_fixed_rate(NULL, of_node_full_name(np),
+ NULL, 0, freq);
+ if (IS_ERR(priv->clk)) {
+ ret = PTR_ERR(priv->clk);
+ goto err_regmap;
+ }
+ artificial_clock = true;
+ }
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ pr_err("%pOF: err %d: clock enable failed\n", np, ret);
+ goto err_clk_init;
+ }
+ clk_rate_exclusive_get(priv->clk);
+
+ if (clocksource_uninitialized) {
+ ret = xilinx_clocksource_init(np);
+ if (ret)
+ goto err_clk_enable;
+ clocksource_uninitialized = false;
+ } else {
+ ret = xilinx_clockevent_init(np, dev);
+ if (ret)
+ goto err_clk_enable;
+ }
+ of_node_set_flag(np, OF_POPULATED);
+
+ if (!one_timer) {
+ dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ if (!dev)
+ return -ENOMEM;
+
+ /*
+ * We don't support removal, so don't bother enabling
+ * the clock twice.
+ */
+ memcpy(&dev->priv, priv, sizeof(dev->priv));
+ dev->priv.map = regmap_init_mmio(NULL, regs + TCSR1,
+ &xilinx_timer_regmap_config);
+ if (!IS_ERR(dev->priv.map)) {
+ ret = xilinx_clockevent_init(np, dev);
+ if (!ret)
+ return 0;
+ regmap_exit(dev->priv.map);
+ } else {
+ ret = PTR_ERR(dev->priv.map);
+ }
+ kfree(dev);
+ }
+ return ret;
+
+err_clk_enable:
+ clk_rate_exclusive_put(priv->clk);
+ clk_disable_unprepare(priv->clk);
+err_clk_init:
+ if (artificial_clock)
+ clk_unregister_fixed_rate(priv->clk);
+ else
+ clk_put(priv->clk);
+err_regmap:
+ regmap_exit(priv->map);
+err_priv:
+ if (!clocksource_uninitialized)
+ kfree(dev);
+err_regs:
+ iounmap(regs);
+ return ret;
+}
+
+TIMER_OF_DECLARE(xilinx_xps_timer, "xlnx,xps-timer-1.00.a", xilinx_timer_init);
new file mode 100644
@@ -0,0 +1,91 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2021 Sean Anderson <sean.anderson@seco.com>
+ */
+
+#ifndef XILINX_TIMER_H
+#define XILINX_TIMER_H
+
+#include <linux/compiler.h>
+
+#define TCSR0 0x00
+#define TLR0 0x04
+#define TCR0 0x08
+#define TCSR1 0x10
+#define TLR1 0x14
+#define TCR1 0x18
+
+#define TCSR_MDT BIT(0)
+#define TCSR_UDT BIT(1)
+#define TCSR_GENT BIT(2)
+#define TCSR_CAPT BIT(3)
+#define TCSR_ARHT BIT(4)
+#define TCSR_LOAD BIT(5)
+#define TCSR_ENIT BIT(6)
+#define TCSR_ENT BIT(7)
+#define TCSR_TINT BIT(8)
+#define TCSR_PWMA BIT(9)
+#define TCSR_ENALL BIT(10)
+#define TCSR_CASC BIT(11)
+
+struct clk;
+struct device_node;
+struct regmap;
+
+/**
+ * struct xilinx_timer_priv - Private data for Xilinx AXI timer drivers
+ * @map: Regmap of the device, possibly with an offset
+ * @clk: Parent clock
+ * @max: Maximum value of the counters
+ */
+struct xilinx_timer_priv {
+ struct regmap *map;
+ struct clk *clk;
+ u32 max;
+};
+
+/**
+ * xilinx_timer_tlr_cycles() - Calculate the TLR for a period specified
+ * in clock cycles
+ * @priv: The timer's private data
+ * @tcsr: The value of the TCSR register for this counter
+ * @cycles: The number of cycles in this period
+ *
+ * Callers of this function MUST ensure that @cycles is representable as
+ * a TLR.
+ *
+ * Return: The calculated value for TLR
+ */
+u32 xilinx_timer_tlr_cycles(struct xilinx_timer_priv *priv, u32 tcsr,
+ u64 cycles);
+
+/**
+ * xilinx_timer_get_period() - Get the current period of a counter
+ * @priv: The timer's private data
+ * @tlr: The value of TLR for this counter
+ * @tcsr: The value of TCSR for this counter
+ *
+ * Return: The period, in ns
+ */
+unsigned int xilinx_timer_get_period(struct xilinx_timer_priv *priv,
+ u32 tlr, u32 tcsr);
+
+/**
+ * xilinx_timer_common_init() - Perform common initialization for Xilinx
+ * AXI timer drivers.
+ * @priv: The timer's private data
+ * @np: The devicetree node for the timer
+ * @one_timer: Set to %1 if there is only one timer
+ *
+ * This performs common initialization, such as detecting endianness,
+ * and parsing devicetree properties. @priv->regs must be initialized
+ * before calling this function. This function initializes @priv->read,
+ * @priv->write, and @priv->width.
+ *
+ * Return: 0, or negative errno
+ */
+int xilinx_timer_common_init(struct device_node *np,
+ struct xilinx_timer_priv *priv,
+ u32 *one_timer);
+
+#endif /* XILINX_TIMER_H */
This rewrites the Xilinx AXI timer driver to be more platform agnostic. Some common code has been split off so it can be reused. These routines currently live in drivers/mfd. The largest changes are summarized below: - We now support any number of timer devices, possibly with only one counter each. The first counter will be used as a clocksource. Every other counter will be used as a clockevent. This allocation scheme was chosen arbitrarily. - We do not use timer_of_init because we need to perform some tasks in between different stages. For example, we must ensure that ->read and ->write are initialized before registering the irq. This can only happen after we have gotten the register base (to detect endianness). We also have a rather unusual clock initialization sequence in order to remain backwards compatible. Due to this, it's ok for the initial clock request to fail, and we do not want other initialization to be undone. Lastly, it is more convenient to do one allocation for xilinx_clockevent_device than to do one for timer_of and one for xilinx_timer_priv. - We now pay attention to xlnx,count-width and handle smaller width timers. The default remains 32. - We access registers using regmap. This automatically deals with endianness issues, so we no longer have to use our own wrappers. It also provides locking for clockevents which have to worry about being interrupted in the middle of a read/modify/write. Note that while the existing timer driver always sets the cpumask to cpu 0, this version sets it to all possible CPUs. I believe this is correct for multiprocessor systems where the timer is not physically wired to a particular CPU's interrupt line. For uniprocessor systems (like most microblaze systems) this makes no difference. Signed-off-by: Sean Anderson <sean.anderson@seco.com> --- This has been tested on microblaze qemu. Changes in v7: - Add dependency on OF_ADDRESS Changes in v6: - Add __init* attributes - Export common symbols - Fix goto'ing incorrect label for cleanup - Remove duplicate regmap_config - Round to closest period in xilinx_timer_get_period to ensure proper semantics for xilinx_pwm_get_state Changes in v5: - Fix some overflows when setting the max value for clockevent and sched_clock - Just use clk_register_fixed_rate instead of the "private" version - Remove duplicate register definitions - Remove xilinx_timer_tlr_period - Remove xlnx,axi-timer-2.0 compatible string - Require that callers check arguments to xilinx_timer_tlr_cycles - Use regmap to deal with endianness issues as suggested by Lee Changes in v4: - Break out clock* drivers into their own file MAINTAINERS | 6 + arch/microblaze/kernel/Makefile | 3 +- arch/microblaze/kernel/timer.c | 326 ---------------------- drivers/clocksource/Kconfig | 13 + drivers/clocksource/Makefile | 1 + drivers/clocksource/timer-xilinx-common.c | 71 +++++ drivers/clocksource/timer-xilinx.c | 323 +++++++++++++++++++++ include/clocksource/timer-xilinx.h | 91 ++++++ 8 files changed, 506 insertions(+), 328 deletions(-) delete mode 100644 arch/microblaze/kernel/timer.c create mode 100644 drivers/clocksource/timer-xilinx-common.c create mode 100644 drivers/clocksource/timer-xilinx.c create mode 100644 include/clocksource/timer-xilinx.h