deleted file mode 100644
@@ -1,54 +0,0 @@
-Drive a GPIO line that can be used to restart the system from a restart
-handler.
-
-This binding supports level and edge triggered reset. At driver load
-time, the driver will request the given gpio line and install a restart
-handler. If the optional properties 'open-source' is not found, the GPIO line
-will be driven in the inactive state. Otherwise its not driven until
-the restart is initiated.
-
-When the system is restarted, the restart handler will be invoked in
-priority order. The gpio is configured as an output, and driven active,
-triggering a level triggered reset condition. This will also cause an
-inactive->active edge condition, triggering positive edge triggered
-reset. After a delay specified by active-delay, the GPIO is set to
-inactive, thus causing an active->inactive edge, triggering negative edge
-triggered reset. After a delay specified by inactive-delay, the GPIO
-is driven active again. After a delay specified by wait-delay, the
-restart handler completes allowing other restart handlers to be attempted.
-
-Required properties:
-- compatible : should be "gpio-restart".
-- gpios : The GPIO to set high/low, see "gpios property" in
- Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
- low to reset the board set it to "Active Low", otherwise set
- gpio to "Active High".
-
-Optional properties:
-- open-source : Treat the GPIO as being open source and defer driving
- it to when the restart is initiated. If this optional property is not
- specified, the GPIO is initialized as an output in its inactive state.
-- priority : A priority ranging from 0 to 255 (default 128) according to
- the following guidelines:
- 0: Restart handler of last resort, with limited restart
- capabilities
- 128: Default restart handler; use if no other restart handler is
- expected to be available, and/or if restart functionality is
- sufficient to restart the entire system
- 255: Highest priority restart handler, will preempt all other
- restart handlers
-- active-delay: Delay (default 100) to wait after driving gpio active [ms]
-- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms]
-- wait-delay: Delay (default 3000) to wait after completing restart
- sequence [ms]
-
-Examples:
-
-gpio-restart {
- compatible = "gpio-restart";
- gpios = <&gpio 4 0>;
- priority = <128>;
- active-delay = <100>;
- inactive-delay = <100>;
- wait-delay = <3000>;
-};
new file mode 100644
@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/reset/gpio-restart.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GPIO-driven system restart
+
+maintainers:
+ - TODO
+
+description:
+ Drive a GPIO line that can be used to restart the system from a restart
+ handler.
+
+ This binding supports level and edge triggered reset. At driver load time,
+ the driver will request the given gpio line and install a restart handler. If
+ the optional properties 'open-source' is not found, the GPIO line will be
+ driven in the inactive state. Otherwise its not driven until the restart is
+ initiated.
+
+ When the system is restarted, the restart handler will be invoked in priority
+ order. The gpio is configured as an output, and driven active, triggering a
+ level triggered reset condition. This will also cause an inactive->active
+ edge condition, triggering positive edge triggered reset. After a delay
+ specified by active-delay, the GPIO is set to inactive, thus causing an
+ active->inactive edge, triggering negative edge triggered reset. After a
+ delay specified by inactive-delay, the GPIO is driven active again. After a
+ delay specified by wait-delay, the restart handler completes allowing other
+ restart handlers to be attempted.
+
+properties:
+ compatible:
+ const: gpio-restart
+
+ gpios:
+ maxItems: 1
+ description:
+ The GPIO to set high/low, see "gpios property" in
+ Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be low
+ to reset the board set it to "Active Low", otherwise set gpio to "Active
+ High".
+
+ open-source:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Treat the GPIO as being open source and defer driving it to when the
+ restart is initiated. If this optional property is not specified, the
+ GPIO is initialized as an output in its inactive state.
+
+ priority:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ A priority ranging from 0 to 255 (default 128) according to the following
+ guidelines:
+ 0: Restart handler of last resort, with limited restart
+ capabilities
+ 128: Default restart handler; use if no other restart handler is
+ expected to be available, and/or if restart functionality is
+ sufficient to restart the entire system
+ 255: Highest priority restart handler, will preempt all other
+ restart handlers
+
+ active-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Delay (default 100) to wait after driving gpio active [ms]
+
+ inactive-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Delay (default 100) to wait after driving gpio inactive [ms]
+
+ wait-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay (default 3000) to wait after completing restart sequence [ms]
+
+required:
+ - compatible
+ - gpios
+
+additionalProperties: false
+
+examples:
+ - |
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio 4 0>;
+ priority = <128>;
+ active-delay = <100>;
+ inactive-delay = <100>;
+ wait-delay = <3000>;
+ };
Convert the gpio-restart binding from plain text format to a schema binding, maintaining the original content and updating formatting where required. Signed-off-by: Sander Vanheule <sander@svanheule.net> --- .../bindings/power/reset/gpio-restart.txt | 54 ----------- .../bindings/power/reset/gpio-restart.yaml | 92 +++++++++++++++++++ 2 files changed, 92 insertions(+), 54 deletions(-) delete mode 100644 Documentation/devicetree/bindings/power/reset/gpio-restart.txt create mode 100644 Documentation/devicetree/bindings/power/reset/gpio-restart.yaml