@@ -1161,6 +1161,16 @@ struct lpfc_hba {
uint32_t cfg_hostmem_hgp;
uint32_t cfg_log_verbose;
uint32_t cfg_enable_fc4_type;
+#define LPFC_ENABLE_FCP 1
+#define LPFC_ENABLE_NVME 2
+#define LPFC_ENABLE_BOTH 3
+#if (IS_ENABLED(CONFIG_NVME_FC))
+#define LPFC_MAX_ENBL_FC4_TYPE LPFC_ENABLE_BOTH
+#define LPFC_DEF_ENBL_FC4_TYPE LPFC_ENABLE_BOTH
+#else
+#define LPFC_MAX_ENBL_FC4_TYPE LPFC_ENABLE_FCP
+#define LPFC_DEF_ENBL_FC4_TYPE LPFC_ENABLE_FCP
+#endif
uint32_t cfg_aer_support;
uint32_t cfg_sriov_nr_virtfn;
uint32_t cfg_request_firmware_upgrade;
@@ -1182,9 +1192,6 @@ struct lpfc_hba {
uint32_t cfg_ras_fwlog_func;
uint32_t cfg_enable_bbcr; /* Enable BB Credit Recovery */
uint32_t cfg_enable_dpp; /* Enable Direct Packet Push */
-#define LPFC_ENABLE_FCP 1
-#define LPFC_ENABLE_NVME 2
-#define LPFC_ENABLE_BOTH 3
uint32_t cfg_enable_pbde;
uint32_t cfg_enable_mi;
struct nvmet_fc_target_port *targetport;
@@ -3978,8 +3978,8 @@ LPFC_ATTR_R(nvmet_mrq_post,
* 3 - register both FCP and NVME
* Supported values are [1,3]. Default value is 3
*/
-LPFC_ATTR_R(enable_fc4_type, LPFC_ENABLE_BOTH,
- LPFC_ENABLE_FCP, LPFC_ENABLE_BOTH,
+LPFC_ATTR_R(enable_fc4_type, LPFC_DEF_ENBL_FC4_TYPE,
+ LPFC_ENABLE_FCP, LPFC_MAX_ENBL_FC4_TYPE,
"Enable FC4 Protocol support - FCP / NVME");
/*
@@ -2104,7 +2104,7 @@ lpfc_handle_eratt_s4(struct lpfc_hba *phba)
}
if (reg_err1 == SLIPORT_ERR1_REG_ERR_CODE_2 &&
reg_err2 == SLIPORT_ERR2_REG_FW_RESTART) {
- lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+ lpfc_printf_log(phba, KERN_ERR, LOG_SLI,
"3143 Port Down: Firmware Update "
"Detected\n");
en_rn_msg = false;
@@ -13363,6 +13363,7 @@ lpfc_sli4_eratt_read(struct lpfc_hba *phba)
uint32_t uerr_sta_hi, uerr_sta_lo;
uint32_t if_type, portsmphr;
struct lpfc_register portstat_reg;
+ u32 logmask;
/*
* For now, use the SLI4 device internal unrecoverable error
@@ -13413,7 +13414,12 @@ lpfc_sli4_eratt_read(struct lpfc_hba *phba)
readl(phba->sli4_hba.u.if_type2.ERR1regaddr);
phba->work_status[1] =
readl(phba->sli4_hba.u.if_type2.ERR2regaddr);
- lpfc_printf_log(phba, KERN_ERR, LOG_TRACE_EVENT,
+ logmask = LOG_TRACE_EVENT;
+ if (phba->work_status[0] ==
+ SLIPORT_ERR1_REG_ERR_CODE_2 &&
+ phba->work_status[1] == SLIPORT_ERR2_REG_FW_RESTART)
+ logmask = LOG_SLI;
+ lpfc_printf_log(phba, KERN_ERR, logmask,
"2885 Port Status Event: "
"port status reg 0x%x, "
"port smphr reg 0x%x, "
Two minor fixes in the lpfc driver. One changing the classification of trace messages and the other fixing a build issue when NVME_FC is disabled. The patch is available here: git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi.git scsi-fixes The short changelog is: James Smart (2): scsi: lpfc: Reduce log messages seen after firmware download scsi: lpfc: Remove NVMe support if kernel has NVME_FC disabled And the diffstat: drivers/scsi/lpfc/lpfc.h | 13 ++++++++++--- drivers/scsi/lpfc/lpfc_attr.c | 4 ++-- drivers/scsi/lpfc/lpfc_init.c | 2 +- drivers/scsi/lpfc/lpfc_sli.c | 8 +++++++- 4 files changed, 20 insertions(+), 7 deletions(-) With full diff below. James ---