diff mbox series

[1/2] dt-bindings: pinctrl: qcom: Add sc8280xp TLMM binding

Message ID 20220225053257.2479279-1-bjorn.andersson@linaro.org
State Superseded
Headers show
Series [1/2] dt-bindings: pinctrl: qcom: Add sc8280xp TLMM binding | expand

Commit Message

Bjorn Andersson Feb. 25, 2022, 5:32 a.m. UTC
The Qualcomm SC8280XP platform contains a single block of registers
for the TLMM block. This provides pinconf and pinmux for 228 GPIOs, 2
UFS_RESET pins and one SDC interface.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 .../pinctrl/qcom,sc8280xp-pinctrl.yaml        | 153 ++++++++++++++++++
 1 file changed, 153 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml

Comments

Krzysztof Kozlowski Feb. 27, 2022, 10:16 a.m. UTC | #1
On 25/02/2022 06:32, Bjorn Andersson wrote:
> The Qualcomm SC8280XP platform contains a single block of registers
> for the TLMM block. This provides pinconf and pinmux for 228 GPIOs, 2
> UFS_RESET pins and one SDC interface.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>  .../pinctrl/qcom,sc8280xp-pinctrl.yaml        | 153 ++++++++++++++++++
>  1 file changed, 153 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
> new file mode 100644
> index 000000000000..4199dfe992e0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
> @@ -0,0 +1,153 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,sc8280xp-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. SC8280XP TLMM block
> +
> +maintainers:
> +  - Bjorn Andersson <bjorn.andersson@linaro.org>
> +
> +description: |
> +  This binding describes the Top Level Mode Multiplexer block found in the
> +  SC8280XP platform.
> +
> +allOf:
> +  - $ref: "pinctrl.yaml#"

This looks not needed. I see it was added in other QCOM schemas by
https://lore.kernel.org/all/20211202063216.24439-1-zajec5@gmail.com/
(+CC RafaƂ) but it is already part of qcom,tlmm-common.yaml. I think
there is no need to include it twice.


> +  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: qcom,sc8280xp-tlmm
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts: true
> +  interrupt-controller: true
> +  '#interrupt-cells': true
> +  gpio-controller: true
> +  gpio-reserved-ranges: true
> +  '#gpio-cells': true
> +  gpio-ranges: true
> +  wakeup-parent: true
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names

I think you do not use it. The example does not have it so it should
fail validation (dt_binding_check).

> +
> +additionalProperties: false
> +
> +patternProperties:
> +  '-state$':
> +    oneOf:
> +      - $ref: "#/$defs/qcom-sc8280xp-tlmm-state"
> +      - patternProperties:
> +          ".*":
> +            $ref: "#/$defs/qcom-sc8280xp-tlmm-state"
> +
> +'$defs':
> +  qcom-sc8280xp-tlmm-state:
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +    $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode.
> +        items:
> +          oneOf:
> +            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-1][0-9]|22[0-7])$"
> +            - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset, ufs1_reset ]
> +        minItems: 1
> +        maxItems: 16
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +
> +        enum: [ atest_char, atest_usb, audio_ref, cam_mclk, cci_async, cci_i2c,
> +                cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
> +                cci_timer5, cci_timer6, cci_timer7, cci_timer8, cci_timer9,
> +                cmu_rng, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
> +                ddr_pxi0, ddr_pxi1, ddr_pxi2, ddr_pxi3, ddr_pxi4, ddr_pxi5,
> +                ddr_pxi6, ddr_pxi7, dp2_hot, dp3_hot, edp0_lcd, edp1_lcd,
> +                edp2_lcd, edp3_lcd, edp_hot, emac0_dll, emac0_mcg0, emac0_mcg1,
> +                emac0_mcg2, emac0_mcg3, emac0_phy, emac0_ptp, emac1_dll0,
> +                emac1_dll1, emac1_mcg0, emac1_mcg1, emac1_mcg2, emac1_mcg3,
> +                emac1_phy, emac1_ptp, gcc_gp1, gcc_gp2, gcc_gp3, gcc_gp4,
> +                gcc_gp5, gpio, hs1_mi2s, hs2_mi2s, hs3_mi2s, ibi_i3c,
> +                jitter_bist, lpass_slimbus, mdp0_vsync0, mdp0_vsync1,
> +                mdp0_vsync2, mdp0_vsync3, mdp0_vsync4, mdp0_vsync5,
> +                mdp0_vsync6, mdp0_vsync7, mdp0_vsync8, mdp1_vsync0,
> +                mdp1_vsync1, mdp1_vsync2, mdp1_vsync3, mdp1_vsync4,
> +                mdp1_vsync5, mdp1_vsync6, mdp1_vsync7, mdp1_vsync8, mdp_vsync,
> +                mi2s0_data0, mi2s0_data1, mi2s0_sck, mi2s0_ws, mi2s1_data0,
> +                mi2s1_data1, mi2s1_sck, mi2s1_ws, mi2s2_data0, mi2s2_data1,
> +                mi2s2_sck, mi2s2_ws, mi2s_mclk1, mi2s_mclk2, pcie2a_clkreq,
> +                pcie2b_clkreq, pcie3a_clkreq, pcie3b_clkreq, pcie4_clkreq,
> +                phase_flag, pll_bist, pll_clk, prng_rosc0, prng_rosc1,
> +                prng_rosc2, prng_rosc3, qdss_cti, qdss_gpio, qspi, qspi_clk,
> +                qspi_cs, qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8,
> +                qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16, qup17,
> +                qup18, qup19, qup20, qup21, qup22, qup23, rgmii_0, rgmii_1,
> +                sd_write, sdc40, sdc42, sdc43, sdc4_clk, sdc4_cmd, tb_trig,
> +                tgu, tsense_pwm1, tsense_pwm2, tsense_pwm3, tsense_pwm4,
> +                usb0_dp, usb0_phy, usb0_sbrx, usb0_sbtx, usb0_usb4, usb1_dp,
> +                usb1_phy, usb1_sbrx, usb1_sbtx, usb1_usb4, usb2phy_ac,
> +                vsense_trigger ]
> +
> +      bias-disable: true
> +      bias-pull-down: true
> +      bias-pull-up: true
> +      drive-strength: true
> +      input-enable: true
> +      output-high: true
> +      output-low: true
> +
> +    required:
> +      - pins
> +      - function
> +
> +    additionalProperties: false
> +
> +examples:
> +  - |
> +        #include <dt-bindings/interrupt-controller/arm-gic.h>
> +        pinctrl@3100000 {
> +                compatible = "qcom,sc8280x-tlmm";
> +                reg = <0x0f100000 0x300000>;

reg looks different than unit address.


Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
new file mode 100644
index 000000000000..4199dfe992e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
@@ -0,0 +1,153 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,sc8280xp-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. SC8280XP TLMM block
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+  This binding describes the Top Level Mode Multiplexer block found in the
+  SC8280XP platform.
+
+allOf:
+  - $ref: "pinctrl.yaml#"
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+  compatible:
+    const: qcom,sc8280xp-tlmm
+
+  reg:
+    maxItems: 1
+
+  interrupts: true
+  interrupt-controller: true
+  '#interrupt-cells': true
+  gpio-controller: true
+  gpio-reserved-ranges: true
+  '#gpio-cells': true
+  gpio-ranges: true
+  wakeup-parent: true
+
+required:
+  - compatible
+  - reg
+  - reg-names
+
+additionalProperties: false
+
+patternProperties:
+  '-state$':
+    oneOf:
+      - $ref: "#/$defs/qcom-sc8280xp-tlmm-state"
+      - patternProperties:
+          ".*":
+            $ref: "#/$defs/qcom-sc8280xp-tlmm-state"
+
+'$defs':
+  qcom-sc8280xp-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|2[0-1][0-9]|22[0-7])$"
+            - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset, ufs1_reset ]
+        minItems: 1
+        maxItems: 16
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+
+        enum: [ atest_char, atest_usb, audio_ref, cam_mclk, cci_async, cci_i2c,
+                cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+                cci_timer5, cci_timer6, cci_timer7, cci_timer8, cci_timer9,
+                cmu_rng, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
+                ddr_pxi0, ddr_pxi1, ddr_pxi2, ddr_pxi3, ddr_pxi4, ddr_pxi5,
+                ddr_pxi6, ddr_pxi7, dp2_hot, dp3_hot, edp0_lcd, edp1_lcd,
+                edp2_lcd, edp3_lcd, edp_hot, emac0_dll, emac0_mcg0, emac0_mcg1,
+                emac0_mcg2, emac0_mcg3, emac0_phy, emac0_ptp, emac1_dll0,
+                emac1_dll1, emac1_mcg0, emac1_mcg1, emac1_mcg2, emac1_mcg3,
+                emac1_phy, emac1_ptp, gcc_gp1, gcc_gp2, gcc_gp3, gcc_gp4,
+                gcc_gp5, gpio, hs1_mi2s, hs2_mi2s, hs3_mi2s, ibi_i3c,
+                jitter_bist, lpass_slimbus, mdp0_vsync0, mdp0_vsync1,
+                mdp0_vsync2, mdp0_vsync3, mdp0_vsync4, mdp0_vsync5,
+                mdp0_vsync6, mdp0_vsync7, mdp0_vsync8, mdp1_vsync0,
+                mdp1_vsync1, mdp1_vsync2, mdp1_vsync3, mdp1_vsync4,
+                mdp1_vsync5, mdp1_vsync6, mdp1_vsync7, mdp1_vsync8, mdp_vsync,
+                mi2s0_data0, mi2s0_data1, mi2s0_sck, mi2s0_ws, mi2s1_data0,
+                mi2s1_data1, mi2s1_sck, mi2s1_ws, mi2s2_data0, mi2s2_data1,
+                mi2s2_sck, mi2s2_ws, mi2s_mclk1, mi2s_mclk2, pcie2a_clkreq,
+                pcie2b_clkreq, pcie3a_clkreq, pcie3b_clkreq, pcie4_clkreq,
+                phase_flag, pll_bist, pll_clk, prng_rosc0, prng_rosc1,
+                prng_rosc2, prng_rosc3, qdss_cti, qdss_gpio, qspi, qspi_clk,
+                qspi_cs, qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8,
+                qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16, qup17,
+                qup18, qup19, qup20, qup21, qup22, qup23, rgmii_0, rgmii_1,
+                sd_write, sdc40, sdc42, sdc43, sdc4_clk, sdc4_cmd, tb_trig,
+                tgu, tsense_pwm1, tsense_pwm2, tsense_pwm3, tsense_pwm4,
+                usb0_dp, usb0_phy, usb0_sbrx, usb0_sbtx, usb0_usb4, usb1_dp,
+                usb1_phy, usb1_sbrx, usb1_sbtx, usb1_usb4, usb2phy_ac,
+                vsense_trigger ]
+
+      bias-disable: true
+      bias-pull-down: true
+      bias-pull-up: true
+      drive-strength: true
+      input-enable: true
+      output-high: true
+      output-low: true
+
+    required:
+      - pins
+      - function
+
+    additionalProperties: false
+
+examples:
+  - |
+        #include <dt-bindings/interrupt-controller/arm-gic.h>
+        pinctrl@3100000 {
+                compatible = "qcom,sc8280x-tlmm";
+                reg = <0x0f100000 0x300000>;
+                interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+                gpio-controller;
+                #gpio-cells = <2>;
+                interrupt-controller;
+                #interrupt-cells = <2>;
+                gpio-ranges = <&tlmm 0 0 230>;
+
+                gpio-wo-subnode-state {
+                        pins = "gpio1";
+                        function = "gpio";
+                };
+
+                uart-w-subnodes-state {
+                        rx {
+                                pins = "gpio4";
+                                function = "qup14";
+                                bias-pull-up;
+                        };
+
+                        tx {
+                                pins = "gpio5";
+                                function = "qup14";
+                                bias-disable;
+                        };
+                };
+        };
+...