@@ -995,7 +995,7 @@ static int mmc_blk_reset(struct mmc_blk_data *md, struct mmc_host *host,
return -EEXIST;
md->reset_done |= type;
- err = mmc_hw_reset(host);
+ err = mmc_hw_reset(host->card);
/* Ensure we switch back to the correct partition */
if (err) {
struct mmc_blk_data *main_md =
@@ -1998,7 +1998,7 @@ static void mmc_hw_reset_for_init(struct mmc_host *host)
/**
* mmc_hw_reset - reset the card in hardware
- * @host: MMC host to which the card is attached
+ * @card: card to be reset
*
* Hard reset the card. This function is only for upper layers, like the
* block layer or card drivers. You cannot use it in host drivers (struct
@@ -2006,8 +2006,9 @@ static void mmc_hw_reset_for_init(struct mmc_host *host)
*
* Return: 0 on success, -errno on failure
*/
-int mmc_hw_reset(struct mmc_host *host)
+int mmc_hw_reset(struct mmc_card *card)
{
+ struct mmc_host *host = card->host;
int ret;
ret = host->bus_ops->hw_reset(host);
@@ -2325,10 +2325,9 @@ static int mmc_test_profile_sglen_r_nonblock_perf(struct mmc_test_card *test)
static int mmc_test_reset(struct mmc_test_card *test)
{
struct mmc_card *card = test->card;
- struct mmc_host *host = card->host;
int err;
- err = mmc_hw_reset(host);
+ err = mmc_hw_reset(card);
if (!err) {
/*
* Reset will re-enable the card's command queue, but tests
@@ -1633,7 +1633,7 @@ static void ath10k_sdio_hif_power_down(struct ath10k *ar)
return;
}
- ret = mmc_hw_reset(ar_sdio->func->card->host);
+ ret = mmc_hw_reset(ar_sdio->func->card);
if (ret)
ath10k_warn(ar, "unable to reset sdio: %d\n", ret);
@@ -4165,7 +4165,7 @@ static int brcmf_sdio_bus_reset(struct device *dev)
/* reset the adapter */
sdio_claim_host(sdiodev->func1);
- mmc_hw_reset(sdiodev->func1->card->host);
+ mmc_hw_reset(sdiodev->func1->card);
sdio_release_host(sdiodev->func1);
brcmf_bus_change_state(sdiodev->bus_if, BRCMF_BUS_DOWN);
@@ -2639,7 +2639,7 @@ static void mwifiex_sdio_card_reset_work(struct mwifiex_adapter *adapter)
/* Run a HW reset of the SDIO interface. */
sdio_claim_host(func);
- ret = mmc_hw_reset(func->card->host);
+ ret = mmc_hw_reset(func->card);
sdio_release_host(func);
switch (ret) {
@@ -146,7 +146,7 @@ static int wl12xx_sdio_power_on(struct wl12xx_sdio_glue *glue)
* To guarantee that the SDIO card is power cycled, as required to make
* the FW programming to succeed, let's do a brute force HW reset.
*/
- mmc_hw_reset(card->host);
+ mmc_hw_reset(card);
sdio_enable_func(func);
sdio_release_host(func);
@@ -175,7 +175,7 @@ void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq);
int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd,
int retries);
-int mmc_hw_reset(struct mmc_host *host);
+int mmc_hw_reset(struct mmc_card *card);
int mmc_sw_reset(struct mmc_host *host);
void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card);
To make it unambiguous that mmc_hw_reset() is for cards and not for controllers, we make the function argument mmc_card instead of mmc_host. Also, all users are converted. Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> --- Ulf prefers one cross-subsystem patch to have all users converted. So, we are looking for ACKs from the maintainers of the wireless drivers. Thank you! Changes since RFC: * don't rename the function but only change the argument type * remove fallback and convert all users in one go * remove comment as suggested by Ulf drivers/mmc/core/block.c | 2 +- drivers/mmc/core/core.c | 5 +++-- drivers/mmc/core/mmc_test.c | 3 +-- drivers/net/wireless/ath/ath10k/sdio.c | 2 +- drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c | 2 +- drivers/net/wireless/marvell/mwifiex/sdio.c | 2 +- drivers/net/wireless/ti/wlcore/sdio.c | 2 +- include/linux/mmc/core.h | 2 +- 8 files changed, 10 insertions(+), 10 deletions(-)