diff mbox series

[3/3] ARM: dts: exynos: add panel and backlight to p4note

Message ID 20220516193709.10037-3-martin.juecker@gmail.com
State New
Headers show
Series [1/3] dt-bindings: display: simple: add support for Samsung LTL101AL01 | expand

Commit Message

Martin Jücker May 16, 2022, 7:37 p.m. UTC
Add configuration for the LTL101AL01 panel and a pwm backlight to drive
the display in the p4note devices.

Signed-off-by: Martin Jücker <martin.juecker@gmail.com>
---
 arch/arm/boot/dts/exynos4412-p4note.dtsi | 84 ++++++++++++++++++++----
 1 file changed, 71 insertions(+), 13 deletions(-)

Comments

Krzysztof Kozlowski June 6, 2022, 9:22 a.m. UTC | #1
On Mon, 16 May 2022 21:37:09 +0200, Martin Jücker wrote:
> Add configuration for the LTL101AL01 panel and a pwm backlight to drive
> the display in the p4note devices.
> 
> 

Applied, thanks!

[3/3] ARM: dts: exynos: add panel and backlight to p4note
      https://git.kernel.org/krzk/linux/c/6c52573bf4c3a0f6e7142264fb36b31ae2c3707a

Best regards,
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/exynos4412-p4note.dtsi b/arch/arm/boot/dts/exynos4412-p4note.dtsi
index 97f131b1014b..1fd051b52387 100644
--- a/arch/arm/boot/dts/exynos4412-p4note.dtsi
+++ b/arch/arm/boot/dts/exynos4412-p4note.dtsi
@@ -106,6 +106,16 @@  voltage-regulator-3 {
 		regulator-always-on;
 	};
 
+	panel_vdd: voltage-regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD_ENABLE";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_enable>;
+		gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
 	wlan_pwrseq: sdhci3-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
@@ -216,6 +226,32 @@  power_supply: charger@6 {
 			monitored-battery = <&battery_cell>;
 		};
 	};
+
+	panel {
+		compatible = "samsung,ltl101al01";
+		pinctrl-0 = <&lvds_nshdn>;
+		pinctrl-names = "default";
+		power-supply = <&panel_vdd>;
+		enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>;
+		backlight = <&backlight>;
+
+		port {
+			lcd_ep: endpoint {
+				remote-endpoint = <&fimd_ep>;
+			};
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-0 = <&led_bl_reset>;
+		pinctrl-names = "default";
+		enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>;
+		pwms = <&pwm 1 78770 0>;
+		brightness-levels = <0 48 128 255>;
+		num-interpolated-steps = <8>;
+		default-brightness-level = <12>;
+	};
 };
 
 &adc {
@@ -295,22 +331,19 @@  &exynos_usbphy {
 };
 
 &fimd {
-	pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+	pinctrl-0 = <&lcd_clk &lcd_data24>;
 	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
-	display-timings {
-		timing0 {
-			clock-frequency = <66666666>;
-			hactive = <1280>;
-			vactive = <800>;
-			hfront-porch = <18>;
-			hback-porch = <36>;
-			hsync-len = <16>;
-			vback-porch = <16>;
-			vfront-porch = <4>;
-			vsync-len = <3>;
-			hsync-active = <1>;
+	samsung,invert-vclk;
+
+	port@3 {
+		reg = <3>;
+
+		fimd_ep: endpoint {
+			remote-endpoint = <&lcd_ep>;
 		};
 	};
 };
@@ -687,6 +720,12 @@  tsp_reg_gpio_3: tsp-reg-gpio-3-pins {
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
+	lcd_enable: lcd-enable-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	sleep0: sleep-state {
 		PIN_SLP(gpa0-0, INPUT, NONE);
 		PIN_SLP(gpa0-1, OUT0, NONE);
@@ -809,12 +848,24 @@  uart_sel: uart-sel-pins {
 		/* 0 = CP, 1 = AP (serial output) */
 	};
 
+	led_bl_reset: led-bl-reset-pins {
+		samsung,pins = "gpm0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	tsp_rst: tsp-rst-pins {
 		samsung,pins = "gpm0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
+	lvds_nshdn: lvds-nshdn-pins {
+		samsung,pins = "gpm0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	tsp_irq: tsp-irq-pins {
 		samsung,pins = "gpm2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
@@ -1100,6 +1151,13 @@  &pmu_system_controller {
 	assigned-clock-parents = <&clock CLK_XUSBXTI>;
 };
 
+&pwm {
+	pinctrl-0 = <&pwm1_out>;
+	pinctrl-names = "default";
+	samsung,pwm-outputs = <1>;
+	status = "okay";
+};
+
 &rtc {
 	clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
 	clock-names = "rtc", "rtc_src";