@@ -14,7 +14,6 @@ on the Qualcomm Hexagon core.
"qcom,msm8974-mss-pil"
"qcom,msm8996-mss-pil"
"qcom,msm8998-mss-pil"
- "qcom,sc7180-mss-pil"
"qcom,sdm845-mss-pil"
- reg:
@@ -46,7 +45,6 @@ on the Qualcomm Hexagon core.
must be "wdog", "fatal", "ready", "handover", "stop-ack"
qcom,msm8996-mss-pil:
qcom,msm8998-mss-pil:
- qcom,sc7180-mss-pil:
qcom,sdm845-mss-pil:
must be "wdog", "fatal", "ready", "handover", "stop-ack",
"shutdown-ack"
@@ -84,9 +82,6 @@ on the Qualcomm Hexagon core.
qcom,msm8998-mss-pil:
must be "iface", "bus", "mem", "xo", "gpll0_mss",
"snoc_axi", "mnoc_axi", "qdss"
- qcom,sc7180-mss-pil:
- must be "iface", "bus", "xo", "snoc_axi", "mnoc_axi",
- "nav"
qcom,sdm845-mss-pil:
must be "iface", "bus", "mem", "xo", "gpll0_mss",
"snoc_axi", "mnoc_axi", "prng"
@@ -98,7 +93,7 @@ on the Qualcomm Hexagon core.
reference to the list of 3 reset-controllers for the
wcss sub-system
reference to the list of 2 reset-controllers for the modem
- sub-system on SC7180, SDM845 SoCs
+ sub-system on SDM845 SoCs
- reset-names:
Usage: required
@@ -107,7 +102,7 @@ on the Qualcomm Hexagon core.
must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset"
for the wcss sub-system
must be "mss_restart", "pdc_reset" for the modem
- sub-system on SC7180, SDM845 SoCs
+ sub-system on SDM845 SoCs
For devices where the mba and mpss sub-nodes are not specified, mba/mpss region
should be referenced as follows:
@@ -172,8 +167,6 @@ For the compatible string below the following supplies are required:
qcom,msm8996-mss-pil:
qcom,msm8998-mss-pil:
must be "cx", "mx"
- qcom,sc7180-mss-pil:
- must be "cx", "mx", "mss"
qcom,sdm845-mss-pil:
must be "cx", "mx", "mss"
@@ -200,15 +193,6 @@ For the compatible string below the following supplies are required:
by the three offsets within syscon for q6, modem and nc
halt registers.
-For the compatible strings below the following phandle references are required:
- "qcom,sc7180-mss-pil"
-- qcom,spare-regs:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: a phandle reference to a syscon representing TCSR followed
- by the offset within syscon for conn_box_spare0 register
- used by the modem sub-system running on SC7180 SoC.
-
The Hexagon node must contain iommus property as described in ../iommu/iommu.txt
on platforms which do not have TrustZone.
new file mode 100644
@@ -0,0 +1,236 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/remoteproc/qcom,sc7180-mss-pil.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SC7180 MSS Peripheral Image Loader
+
+maintainers:
+ - Sibi Sankar <quic_sibis@quicinc.com>
+
+description:
+ This document describes the hardware for a component that loads and boots firmware
+ on the Qualcomm Technology Inc. SC7180 Modem Hexagon Core.
+
+properties:
+ compatible:
+ enum:
+ - qcom,sc7180-mss-pil
+
+ reg:
+ items:
+ - description: MSS QDSP6 registers
+ - description: RMB registers
+
+ reg-names:
+ items:
+ - const: qdsp6
+ - const: rmb
+
+ iommus:
+ items:
+ - description: MSA Stream 1
+ - description: MSA Stream 2
+
+ interrupts:
+ items:
+ - description: Watchdog interrupt
+ - description: Fatal interrupt
+ - description: Ready interrupt
+ - description: Handover interrupt
+ - description: Stop acknowledge interrupt
+ - description: Shutdown acknowledge interrupt
+
+ interrupt-names:
+ items:
+ - const: wdog
+ - const: fatal
+ - const: ready
+ - const: handover
+ - const: stop-ack
+ - const: shutdown-ack
+
+ clocks:
+ items:
+ - description: GCC MSS IFACE clock
+ - description: GCC MSS BUS clock
+ - description: GCC MSS NAV clock
+ - description: GCC MSS SNOC_AXI clock
+ - description: GCC MSS MFAB_AXIS clock
+ - description: RPMH XO clock
+
+ clock-names:
+ items:
+ - const: iface
+ - const: bus
+ - const: nav
+ - const: snoc_axi
+ - const: mnoc_axi
+ - const: xo
+
+ power-domains:
+ items:
+ - description: CX power domain
+ - description: MX power domain
+ - description: MSS power domain
+
+ power-domain-names:
+ items:
+ - const: cx
+ - const: mx
+ - const: mss
+
+ resets:
+ items:
+ - description: AOSS restart
+ - description: PDC reset
+
+ reset-names:
+ items:
+ - const: mss_restart
+ - const: pdc_reset
+
+ memory-region:
+ maxItems: 2
+ description: Phandle reference to the reserved-memory for the MBA region followed
+ by the modem region.
+
+ firmware-name:
+ $ref: /schemas/types.yaml#/definitions/string-array
+ maxItems: 2
+ description:
+ The name of the MBA and modem firmware to be loaded for this remote processor.
+
+ qcom,halt-regs:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description:
+ Phandle reference to a syscon representing TCSR followed by the
+ three offsets within syscon for q6, modem and nc halt registers.
+
+ qcom,spare-regs:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description:
+ Phandle reference to a syscon representing TCSR followed by the
+ offset within syscon for conn_box_spare0 register.
+
+ qcom,qmp:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: Reference to the AOSS side-channel message RAM.
+
+ qcom,smem-states:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: States used by the AP to signal the Hexagon core
+ items:
+ - description: Stop the modem
+
+ qcom,smem-state-names:
+ description: The names of the state bits used for SMP2P output
+ const: stop
+
+ glink-edge:
+ $ref: qcom,glink-edge.yaml#
+ description:
+ Qualcomm G-Link subnode which represents communication edge, channels
+ and devices related to the DSP.
+
+ properties:
+ interrupts:
+ items:
+ - description: IRQ from MSS to GLINK
+
+ mboxes:
+ items:
+ - description: Mailbox for communication between APPS and MSS
+
+ label:
+ items:
+ - const: modem
+
+ apr: false
+ fastrpc: false
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - iommus
+ - interrupts
+ - interrupt-names
+ - clocks
+ - clock-names
+ - power-domains
+ - power-domain-names
+ - resets
+ - reset-names
+ - qcom,halt-regs
+ - qcom,spare-regs
+ - memory-region
+ - qcom,qmp
+ - qcom,smem-states
+ - qcom,smem-state-names
+ - glink-edge
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+ #include <dt-bindings/reset/qcom,sdm845-aoss.h>
+ #include <dt-bindings/reset/qcom,sdm845-pdc.h>
+
+ remoteproc_mpss: remoteproc@4080000 {
+ compatible = "qcom,sc7180-mss-pil";
+ reg = <0x04080000 0x10000>, <0x04180000 0x48>;
+ reg-names = "qdsp6", "rmb";
+
+ iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
+
+ interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+ <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-names = "wdog", "fatal", "ready", "handover",
+ "stop-ack", "shutdown-ack";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+ <&gcc GCC_MSS_NAV_AXI_CLK>,
+ <&gcc GCC_MSS_SNOC_AXI_CLK>,
+ <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "bus", "nav", "snoc_axi",
+ "mnoc_axi", "xo";
+
+ power-domains = <&rpmhpd SC7180_CX>,
+ <&rpmhpd SC7180_MX>,
+ <&rpmhpd SC7180_MSS>;
+ power-domain-names = "cx", "mx", "mss";
+
+ memory-region = <&mba_mem>, <&mpss_mem>;
+
+ qcom,qmp = <&aoss_qmp>;
+
+ qcom,smem-states = <&modem_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+ <&pdc_reset PDC_MODEM_SYNC_RESET>;
+ reset-names = "mss_restart", "pdc_reset";
+
+ qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+ qcom,spare-regs = <&tcsr_regs 0xb3e4>;
+
+ glink-edge {
+ interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&apss_shared 12>;
+ qcom,remote-pid = <1>;
+ label = "modem";
+ };
+ };
Convert SC7180 MSS PIL loading bindings to YAML. Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> --- .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 20 +- .../bindings/remoteproc/qcom,sc7180-mss-pil.yaml | 236 +++++++++++++++++++++ 2 files changed, 238 insertions(+), 18 deletions(-) create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7180-mss-pil.yaml