@@ -320,15 +320,8 @@ static inline int read_sub_irq_data(struct regmap_irq_chip_data *data,
unsigned int offset = subreg->offset[i];
unsigned int index = offset / map->reg_stride;
- if (chip->not_fixed_stride)
- ret = regmap_read(map,
- chip->status_base + offset,
- &data->status_buf[b]);
- else
- ret = regmap_read(map,
- chip->status_base + offset,
- &data->status_buf[index]);
-
+ ret = regmap_read(map, chip->status_base + offset,
+ &data->status_buf[index]);
if (ret)
break;
}
@@ -380,18 +373,7 @@ static irqreturn_t regmap_irq_thread(int irq, void *d)
* sake of simplicity. and add bulk reads only if needed
*/
for (i = 0; i < chip->num_main_regs; i++) {
- /*
- * For not_fixed_stride, don't use get_irq_reg().
- * It would produce an incorrect result.
- */
- if (data->chip->not_fixed_stride)
- reg = chip->main_status +
- (i * map->reg_stride *
- data->irq_reg_stride);
- else
- reg = data->get_irq_reg(data,
- chip->main_status, i);
-
+ reg = data->get_irq_reg(data, chip->main_status, i);
ret = regmap_read(map, reg, &data->main_status_buf[i]);
if (ret) {
dev_err(map->dev,
@@ -561,17 +543,6 @@ unsigned int regmap_irq_get_irq_reg_linear(struct regmap_irq_chip_data *data,
const struct regmap_irq_chip *chip = data->chip;
struct regmap *map = data->map;
- /*
- * NOTE: This is for backward compatibility only and will be removed
- * when not_fixed_stride is dropped (it's only used by qcom-pm8008).
- */
- if (chip->not_fixed_stride && chip->sub_reg_offsets) {
- struct regmap_irq_sub_irq_map *subreg;
-
- subreg = &chip->sub_reg_offsets[0];
- return base + subreg->offset[0];
- }
-
return base + index * (map->reg_stride * chip->irq_reg_stride);
}
EXPORT_SYMBOL_GPL(regmap_irq_get_irq_reg_linear);
@@ -674,12 +645,6 @@ int regmap_add_irq_chip_fwnode(struct fwnode_handle *fwnode,
return -EINVAL;
}
- if (chip->not_fixed_stride) {
- for (i = 0; i < chip->num_regs; i++)
- if (chip->sub_reg_offsets[i].num_regs != 1)
- return -EINVAL;
- }
-
if (irq_base) {
irq_base = irq_alloc_descs(irq_base, 0, chip->num_irqs, 0);
if (irq_base < 0) {
@@ -1446,9 +1446,6 @@ struct regmap_irq_chip_data;
* status_base. Should contain num_regs arrays.
* Can be provided for chips with more complex mapping than
* 1.st bit to 1.st sub-reg, 2.nd bit to 2.nd sub-reg, ...
- * When used with not_fixed_stride, each one-element array
- * member contains offset calculated as address from each
- * peripheral to first peripheral.
* @num_main_regs: Number of 'main status' irq registers for chips which have
* main_status set.
*
@@ -1474,9 +1471,6 @@ struct regmap_irq_chip_data;
* @clear_on_unmask: For chips with interrupts cleared on read: read the status
* registers before unmasking interrupts to clear any bits
* set when they were masked.
- * @not_fixed_stride: Used when chip peripherals are not laid out with fixed
- * stride. Must be used with sub_reg_offsets containing the
- * offsets to each peripheral.
* @status_invert: Inverted status register: cleared bits are active interrupts.
* @runtime_pm: Hold a runtime PM lock on the device when accessing it.
*
@@ -1529,7 +1523,6 @@ struct regmap_irq_chip {
bool runtime_pm:1;
bool type_in_mask:1;
bool clear_on_unmask:1;
- bool not_fixed_stride:1;
bool status_invert:1;
int num_regs;
Clean up all the cruft related to not_fixed_stride. The same thing can be accomplished with a custom get_irq_reg() callback. Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> --- drivers/base/regmap/regmap-irq.c | 41 +++----------------------------- include/linux/regmap.h | 7 ------ 2 files changed, 3 insertions(+), 45 deletions(-)