new file mode 100644
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2022 Microchip Technology, Inc. and its subsidiaries
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/watchdog/atmel,at91sam9-wdt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Atmel Watchdog Timers
+
+maintainers:
+ - Eugen Hristev <eugen.hristev@microchip.com>
+
+properties:
+ compatible:
+ const: atmel,at91sam9260-wdt
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ atmel,max-heartbeat-sec:
+ description:
+ Should contain the maximum heartbeat value in seconds. This value
+ should be less or equal to 16. It is used to compute the WDV field.
+ maximum: 16
+
+ atmel,min-heartbeat-sec:
+ description:
+ Should contain the minimum heartbeat value in seconds. This value
+ must be smaller than the max-heartbeat-sec value. It is used to
+ compute the WDD field.
+ maximum: 16
+
+ atmel,watchdog-type:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: |
+ Should be hardware or software.
+ oneOf:
+ - description:
+ Hardware watchdog uses the at91 watchdog reset.
+ const: hardware
+ - description: |
+ Software watchdog uses the watchdog interrupt
+ to trigger a software reset.
+ const: software
+ default: hardware
+
+ atmel,reset-type:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: |
+ Should be proc or all. This is valid only when using hardware watchdog.
+ oneOf:
+ - description:
+ Assert peripherals and processor reset signals.
+ const: all
+ - description:
+ Assert the processor reset signal.
+ const: proc
+ default: all
+
+ atmel,disable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Should be present if you want to stop the watchdog.
+
+ atmel,idle-halt:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Should be present if you want to stop the watchdog when
+ entering idle state.
+ CAUTION: This property should be used with care, it actually makes the
+ watchdog not counting when the CPU is in idle state, therefore the
+ watchdog reset time depends on mean CPU usage and will not reset at all
+ if the CPU stops working while it is in idle state, which is probably
+ not what you want.
+
+ atmel,dbg-halt:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Should be present if you want to stop the watchdog when
+ entering debug state.
+
+required:
+ - compatible
+ - reg
+ - clocks
+
+allOf:
+ - $ref: watchdog.yaml#
+ - if:
+ properties:
+ atmel,reset-type:
+ enum:
+ - all
+ - proc
+ then:
+ properties:
+ atmel,watchdog-type:
+ const: hardware
+
+dependencies:
+ atmel,reset-type: ['atmel,watchdog-type']
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ watchdog@fffffd40 {
+ compatible = "atmel,at91sam9260-wdt";
+ reg = <0xfffffd40 0x10>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k>;
+ timeout-sec = <15>;
+ atmel,watchdog-type = "hardware";
+ atmel,reset-type = "all";
+ atmel,dbg-halt;
+ atmel,idle-halt;
+ atmel,max-heartbeat-sec = <16>;
+ atmel,min-heartbeat-sec = <0>;
+ };
deleted file mode 100644
@@ -1,51 +0,0 @@
-* Atmel Watchdog Timers
-
-** at91sam9-wdt
-
-Required properties:
-- compatible: must be "atmel,at91sam9260-wdt".
-- reg: physical base address of the controller and length of memory mapped
- region.
-- clocks: phandle to input clock.
-
-Optional properties:
-- timeout-sec: contains the watchdog timeout in seconds.
-- interrupts : Should contain WDT interrupt.
-- atmel,max-heartbeat-sec : Should contain the maximum heartbeat value in
- seconds. This value should be less or equal to 16. It is used to
- compute the WDV field.
-- atmel,min-heartbeat-sec : Should contain the minimum heartbeat value in
- seconds. This value must be smaller than the max-heartbeat-sec value.
- It is used to compute the WDD field.
-- atmel,watchdog-type : Should be "hardware" or "software". Hardware watchdog
- use the at91 watchdog reset. Software watchdog use the watchdog
- interrupt to trigger a software reset.
-- atmel,reset-type : Should be "proc" or "all".
- "all" : assert peripherals and processor reset signals
- "proc" : assert the processor reset signal
- This is valid only when using "hardware" watchdog.
-- atmel,disable : Should be present if you want to disable the watchdog.
-- atmel,idle-halt : Should be present if you want to stop the watchdog when
- entering idle state.
- CAUTION: This property should be used with care, it actually makes the
- watchdog not counting when the CPU is in idle state, therefore the
- watchdog reset time depends on mean CPU usage and will not reset at all
- if the CPU stop working while it is in idle state, which is probably
- not what you want.
-- atmel,dbg-halt : Should be present if you want to stop the watchdog when
- entering debug state.
-
-Example:
- watchdog@fffffd40 {
- compatible = "atmel,at91sam9260-wdt";
- reg = <0xfffffd40 0x10>;
- interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
- clocks = <&clk32k>;
- timeout-sec = <15>;
- atmel,watchdog-type = "hardware";
- atmel,reset-type = "all";
- atmel,dbg-halt;
- atmel,idle-halt;
- atmel,max-heartbeat-sec = <16>;
- atmel,min-heartbeat-sec = <0>;
- };