diff mbox

[2/8] android_pipe: don't be clever with #define offsets

Message ID 20160106140424.3661.36799.stgit@localhost.localdomain
State New
Headers show

Commit Message

Alan Cox Jan. 6, 2016, 2:04 p.m. UTC 
From: Alex Bennée <alex.bennee@linaro.org>


It just makes it harder to figure out which commands are being used.

Signed-off-by: Alex Bennée <alex.bennee@linaro.org>

Signed-off-by: Jin Qian <jinqian@android.com>

Signed-off-by: Alan Cox <alan@linux.intel.com>

---
 drivers/platform/goldfish/goldfish_pipe.c |   16 +++++-----------
 1 file changed, 5 insertions(+), 11 deletions(-)


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
diff mbox

Patch

diff --git a/drivers/platform/goldfish/goldfish_pipe.c b/drivers/platform/goldfish/goldfish_pipe.c
index e7a29e2..0fb3a34 100644
--- a/drivers/platform/goldfish/goldfish_pipe.c
+++ b/drivers/platform/goldfish/goldfish_pipe.c
@@ -90,12 +90,6 @@ 
 #define CMD_WRITE_BUFFER	4  /* send a user buffer to the emulator */
 #define CMD_WAKE_ON_WRITE	5  /* tell the emulator to wake us when writing
 				     is possible */
-
-/* The following commands are related to read operations, they must be
- * listed in the same order than the corresponding write ones, since we
- * will use (CMD_READ_BUFFER - CMD_WRITE_BUFFER) as a special offset
- * in goldfish_pipe_read_write() below.
- */
 #define CMD_READ_BUFFER        6  /* receive a user buffer from the emulator */
 #define CMD_WAKE_ON_READ       7  /* tell the emulator to wake us when reading
 				   * is possible */
@@ -272,8 +266,6 @@  static ssize_t goldfish_pipe_read_write(struct file *filp, char __user *buffer,
 	unsigned long irq_flags;
 	struct goldfish_pipe *pipe = filp->private_data;
 	struct goldfish_pipe_dev *dev = pipe->dev;
-	const int cmd_offset = is_write ? 0
-					: (CMD_READ_BUFFER - CMD_WRITE_BUFFER);
 	unsigned long address, address_end;
 	int ret = 0;
 
@@ -325,7 +317,8 @@  static ssize_t goldfish_pipe_read_write(struct file *filp, char __user *buffer,
 
 		/* Now, try to transfer the bytes in the current page */
 		spin_lock_irqsave(&dev->lock, irq_flags);
-		if (access_with_param(dev, CMD_WRITE_BUFFER + cmd_offset,
+		if (access_with_param(dev,
+				is_write ? CMD_WRITE_BUFFER : CMD_READ_BUFFER,
 				address, avail, pipe, &status)) {
 			gf_write_ptr(pipe, dev->base + PIPE_REG_CHANNEL,
 				     dev->base + PIPE_REG_CHANNEL_HIGH);
@@ -333,7 +326,7 @@  static ssize_t goldfish_pipe_read_write(struct file *filp, char __user *buffer,
 			gf_write_ptr((void *)address,
 				     dev->base + PIPE_REG_ADDRESS,
 				     dev->base + PIPE_REG_ADDRESS_HIGH);
-			writel(CMD_WRITE_BUFFER + cmd_offset,
+			writel(is_write ? CMD_WRITE_BUFFER : CMD_READ_BUFFER,
 					dev->base + PIPE_REG_COMMAND);
 			status = readl(dev->base + PIPE_REG_STATUS);
 		}
@@ -370,7 +363,8 @@  static ssize_t goldfish_pipe_read_write(struct file *filp, char __user *buffer,
 		set_bit(wakeBit, &pipe->flags);
 
 		/* Tell the emulator we're going to wait for a wake event */
-		goldfish_cmd(pipe, CMD_WAKE_ON_WRITE + cmd_offset);
+		goldfish_cmd(pipe,
+			is_write ? CMD_WAKE_ON_WRITE : CMD_WAKE_ON_READ);
 
 		/* Unlock the pipe, then wait for the wake signal */
 		mutex_unlock(&pipe->lock);