diff mbox series

[v3,30/35] scsi: Have scsi-ml retry scsi_report_lun_scan errors

Message ID 20221003175321.8040-31-michael.christie@oracle.com
State Superseded
Headers show
Series Allow scsi_execute users to control retries | expand

Commit Message

Mike Christie Oct. 3, 2022, 5:53 p.m. UTC
This has scsi_report_lun_scan have scsi-ml retry errors instead of driving
them itself.

Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
---
 drivers/scsi/scsi_scan.c | 54 +++++++++++++++++++---------------------
 1 file changed, 25 insertions(+), 29 deletions(-)
diff mbox series

Patch

diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c
index c45646da6c71..e3693aa95543 100644
--- a/drivers/scsi/scsi_scan.c
+++ b/drivers/scsi/scsi_scan.c
@@ -1420,13 +1420,21 @@  static int scsi_report_lun_scan(struct scsi_target *starget, blist_flags_t bflag
 	unsigned int length;
 	u64 lun;
 	unsigned int num_luns;
-	unsigned int retries;
 	int result;
 	struct scsi_lun *lunp, *lun_data;
-	struct scsi_sense_hdr sshdr;
 	struct scsi_device *sdev;
 	struct Scsi_Host *shost = dev_to_shost(&starget->dev);
 	int ret = 0;
+	struct scsi_failure failures[] = {
+		{
+			.sense = UNIT_ATTENTION,
+			.asc = SCMD_FAILURE_ASC_ANY,
+			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.allowed = 3,
+			.result = SAM_STAT_CHECK_CONDITION,
+		},
+		{},
+	};
 
 	/*
 	 * Only support SCSI-3 and up devices if BLIST_NOREPORTLUN is not set.
@@ -1495,34 +1503,22 @@  static int scsi_report_lun_scan(struct scsi_target *starget, blist_flags_t bflag
 	 * should come through as a check condition, and will not generate
 	 * a retry.
 	 */
-	for (retries = 0; retries < 3; retries++) {
-		SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
-				"scsi scan: Sending REPORT LUNS to (try %d)\n",
-				retries));
-
-		result = scsi_exec_req(((struct scsi_exec_args) {
-						.sdev = sdev,
-						.cmd = scsi_cmd,
-						.data_dir = DMA_FROM_DEVICE,
-						.buf = lun_data,
-						.buf_len = length,
-						.sshdr = &sshdr,
-						.timeout = SCSI_REPORT_LUNS_TIMEOUT,
-						.retries = 3 }));
-
-		SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
-				"scsi scan: REPORT LUNS"
-				" %s (try %d) result 0x%x\n",
-				result ?  "failed" : "successful",
-				retries, result));
-		if (result == 0)
-			break;
-		else if (scsi_sense_valid(&sshdr)) {
-			if (sshdr.sense_key != UNIT_ATTENTION)
-				break;
-		}
-	}
+	SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
+			  "scsi scan: Sending REPORT LUNS\n"));
+
+	result = scsi_exec_req(((struct scsi_exec_args) {
+					.sdev = sdev,
+					.cmd = scsi_cmd,
+					.data_dir = DMA_FROM_DEVICE,
+					.buf = lun_data,
+					.buf_len = length,
+					.timeout = SCSI_REPORT_LUNS_TIMEOUT,
+					.retries = 3,
+					.failures = failures }));
 
+	SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
+			  "scsi scan: REPORT LUNS %s result 0x%x\n",
+			  result ?  "failed" : "successful", result));
 	if (result) {
 		/*
 		 * The device probably does not support a REPORT LUN command