@@ -30,7 +30,6 @@
#include <linux/mmc/host.h>
#include <linux/mmc/sdio.h>
-#include <linux/atmel-mci.h>
#include <linux/atmel_pdc.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>
@@ -41,6 +40,8 @@
#include <asm/unaligned.h>
#include "../core/pwrseq.h"
+#define ATMCI_MAX_NR_SLOTS 2
+
/*
* Superset of MCI IP registers integrated in Atmel AT91 Processor
* Registers and bitfields marked with [2] are only available in MCI2
@@ -202,6 +203,42 @@ enum atmci_pdc_buf {
PDC_SECOND_BUF,
};
+/**
+ * struct mci_slot_pdata - board-specific per-slot configuration
+ * @bus_width: Number of data lines wired up the slot
+ * @detect_pin: GPIO pin wired to the card detect switch
+ * @wp_pin: GPIO pin wired to the write protect sensor
+ * @detect_is_active_high: The state of the detect pin when it is active
+ * @non_removable: The slot is not removable, only detect once
+ *
+ * If a given slot is not present on the board, @bus_width should be
+ * set to 0. The other fields are ignored in this case.
+ *
+ * Any pins that aren't available should be set to a negative value.
+ *
+ * Note that support for multiple slots is experimental -- some cards
+ * might get upset if we don't get the clock management exactly right.
+ * But in most cases, it should work just fine.
+ */
+struct mci_slot_pdata {
+ unsigned int bus_width;
+ struct gpio_desc *detect_pin;
+ struct gpio_desc *wp_pin;
+ bool detect_is_active_high;
+ bool non_removable;
+};
+
+/**
+ * struct mci_platform_data - board-specific MMC/SDcard configuration
+ * @dma_slave: DMA slave interface to use in data transfers.
+ * @slot: Per-slot configuration data.
+ */
+struct mci_platform_data {
+ void *dma_slave;
+ dma_filter_fn dma_filter;
+ struct mci_slot_pdata slot[ATMCI_MAX_NR_SLOTS];
+};
+
struct atmel_mci_caps {
bool has_dma_conf_reg;
bool has_pdc;
deleted file mode 100644
@@ -1,46 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __LINUX_ATMEL_MCI_H
-#define __LINUX_ATMEL_MCI_H
-
-#include <linux/types.h>
-#include <linux/dmaengine.h>
-
-#define ATMCI_MAX_NR_SLOTS 2
-
-/**
- * struct mci_slot_pdata - board-specific per-slot configuration
- * @bus_width: Number of data lines wired up the slot
- * @detect_pin: GPIO pin wired to the card detect switch
- * @wp_pin: GPIO pin wired to the write protect sensor
- * @detect_is_active_high: The state of the detect pin when it is active
- * @non_removable: The slot is not removable, only detect once
- *
- * If a given slot is not present on the board, @bus_width should be
- * set to 0. The other fields are ignored in this case.
- *
- * Any pins that aren't available should be set to a negative value.
- *
- * Note that support for multiple slots is experimental -- some cards
- * might get upset if we don't get the clock management exactly right.
- * But in most cases, it should work just fine.
- */
-struct mci_slot_pdata {
- unsigned int bus_width;
- struct gpio_desc *detect_pin;
- struct gpio_desc *wp_pin;
- bool detect_is_active_high;
- bool non_removable;
-};
-
-/**
- * struct mci_platform_data - board-specific MMC/SDcard configuration
- * @dma_slave: DMA slave interface to use in data transfers.
- * @slot: Per-slot configuration data.
- */
-struct mci_platform_data {
- void *dma_slave;
- dma_filter_fn dma_filter;
- struct mci_slot_pdata slot[ATMCI_MAX_NR_SLOTS];
-};
-
-#endif /* __LINUX_ATMEL_MCI_H */
Move the contents of linux/atmel-mci.h into drivers/mmc/host/atmel-mci.c as it is only used in one file Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com> --- drivers/mmc/host/atmel-mci.c | 39 +++++++++++++++++++++++++++++- include/linux/atmel-mci.h | 46 ------------------------------------ 2 files changed, 38 insertions(+), 47 deletions(-) delete mode 100644 include/linux/atmel-mci.h