diff mbox series

Bluetooth: Fix issue with Actions Semi ATS2851 based devices

Message ID 20221216201247.297210-1-marcel@holtmann.org
State Accepted
Commit b03b141b1e81ee18dc04534fccf19c0895249f46
Headers show
Series Bluetooth: Fix issue with Actions Semi ATS2851 based devices | expand

Commit Message

Marcel Holtmann Dec. 16, 2022, 8:12 p.m. UTC
Their devices claim to support the erroneous data reporting, but don't
actually support the required commands. So blacklist them and add a
quirk.

  < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
  > HCI Event: Command Status (0x0f) plen 4
        Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
          Status: Unknown HCI Command (0x01)

T:  Bus=02 Lev=02 Prnt=08 Port=02 Cnt=01 Dev#= 10 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=10d7 ProdID=b012 Rev=88.91
S:  Manufacturer=Actions
S:  Product=general adapter
S:  SerialNumber=ACTIONS1234
C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=01(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=01(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=01(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=01(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=01(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=01(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
---
 drivers/bluetooth/btusb.c | 9 +++++++++
 1 file changed, 9 insertions(+)

Comments

Christopher Snowhill March 29, 2023, 5:07 a.m. UTC | #1
On Fri, Dec 16, 2022, at 12:12 PM, Marcel Holtmann wrote:
> Their devices claim to support the erroneous data reporting, but don't
> actually support the required commands. So blacklist them and add a
> quirk.

This device appears to not support HCI_OP_LE_READ_TRANSMIT_POWER,
either. I get this with the above patch applied:

> Bluetooth: hci0: Opcode 0x204b failed: -56

Then it fails to register as a functioning interface, and bluez thinks
bluetooth is turned off.

In my case, it's a Techkey long range adapter, which is probably a similar
model to the above mentioned Ugreen device, except that it also has a
detachable pole antenna.
Christopher Snowhill March 29, 2023, 5:09 a.m. UTC | #2
So sorry for the noise, I didn't notice there was a new patch revision.
diff mbox series

Patch

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 2ad4efdd9e40..afd2f08ffe30 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -64,6 +64,7 @@  static struct usb_driver btusb_driver;
 #define BTUSB_INTEL_BROKEN_SHUTDOWN_LED	BIT(24)
 #define BTUSB_INTEL_BROKEN_INITIAL_NCMD BIT(25)
 #define BTUSB_INTEL_NO_WBS_SUPPORT	BIT(26)
+#define BTUSB_ACTIONS_SEMI		BIT(27)
 
 static const struct usb_device_id btusb_table[] = {
 	/* Generic Bluetooth USB device */
@@ -677,6 +678,9 @@  static const struct usb_device_id blacklist_table[] = {
 	{ USB_DEVICE(0x0cb5, 0xc547), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
 
+	/* Actions Semiconductor ATS2851 based devices */
+	{ USB_DEVICE(0x10d7, 0xb012), .driver_info = BTUSB_ACTIONS_SEMI },
+
 	/* Silicon Wave based devices */
 	{ USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_SWAVE },
 
@@ -4098,6 +4102,11 @@  static int btusb_probe(struct usb_interface *intf,
 		set_bit(BTUSB_USE_ALT3_FOR_WBS, &data->flags);
 	}
 
+	if (id->driver_info & BTUSB_ACTIONS_SEMI) {
+		/* Support is advertised, but not implemented */
+		set_bit(HCI_QUIRK_BROKEN_ERR_DATA_REPORTING, &hdev->quirks);
+	}
+
 	if (!reset)
 		set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);