new file mode 100644
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/samsung,s5k5baf.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+properties:
+ compatible:
+ const: samsung,s5k5baf
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: mclk
+
+ clock-frequency:
+ default: 24000000
+ description: mclk clock frequency
+
+ rstn-gpios:
+ maxItems: 1
+ description: RSTN pin
+
+ stbyn-gpios:
+ maxItems: 1
+ description: STDBYN pin
+
+ vdda-supply:
+ description: Analog power supply 2.8V (2.6V to 3.0V)
+
+ vddio-supply:
+ description: I/O power supply 1.8V (1.65V to 1.95V) or 2.8V (2.5V to 3.1V)
+
+ vddreg-supply:
+ description:
+ Regulator input power supply 1.8V (1.7V to 1.9V) or 2.8V (2.6V to 3.0)
+
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ additionalProperties: false
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ items:
+ - const: 1
+
+required:
+ - compatible
+ - clocks
+ - clock-names
+ - rstn-gpios
+ - stbyn-gpios
+ - vdda-supply
+ - vddio-supply
+ - vddreg-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sensor@2d {
+ compatible = "samsung,s5k5baf";
+ reg = <0x2d>;
+ clocks = <&camera 0>;
+ clock-names = "mclk";
+ clock-frequency = <24000000>;
+ rstn-gpios = <&gpl2 1 GPIO_ACTIVE_LOW>;
+ stbyn-gpios = <&gpl2 0 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&cam_io_en_reg>;
+ vddio-supply = <&vtcam_reg>;
+ vddreg-supply = <&vt_core_15v_reg>;
+
+ port {
+ endpoint {
+ remote-endpoint = <&csis1_ep>;
+ data-lanes = <1>;
+ };
+ };
+ };
+ };
deleted file mode 100644
@@ -1,58 +0,0 @@
-Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP
---------------------------------------------------------------------
-
-Required properties:
-
-- compatible : "samsung,s5k5baf";
-- reg : I2C slave address of the sensor;
-- vdda-supply : analog power supply 2.8V (2.6V to 3.0V);
-- vddreg-supply : regulator input power supply 1.8V (1.7V to 1.9V)
- or 2.8V (2.6V to 3.0);
-- vddio-supply : I/O power supply 1.8V (1.65V to 1.95V)
- or 2.8V (2.5V to 3.1V);
-- stbyn-gpios : GPIO connected to STDBYN pin;
-- rstn-gpios : GPIO connected to RSTN pin;
-- clocks : list of phandle and clock specifier pairs
- according to common clock bindings for the
- clocks described in clock-names;
-- clock-names : should include "mclk" for the sensor's master clock;
-
-Optional properties:
-
-- clock-frequency : the frequency at which the "mclk" clock should be
- configured to operate, in Hz; if this property is not
- specified default 24 MHz value will be used.
-
-The device node should contain one 'port' child node with one child 'endpoint'
-node, according to the bindings defined in Documentation/devicetree/bindings/
-media/video-interfaces.txt. The following are properties specific to those
-nodes.
-
-endpoint node
--------------
-
-- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
- video-interfaces.txt. If present it should be <1> - the device
- supports only one data lane without re-mapping.
-
-Example:
-
-s5k5bafx@2d {
- compatible = "samsung,s5k5baf";
- reg = <0x2d>;
- vdda-supply = <&cam_io_en_reg>;
- vddreg-supply = <&vt_core_15v_reg>;
- vddio-supply = <&vtcam_reg>;
- stbyn-gpios = <&gpl2 0 1>;
- rstn-gpios = <&gpl2 1 1>;
- clock-names = "mclk";
- clocks = <&clock_cam 0>;
- clock-frequency = <24000000>;
-
- port {
- s5k5bafx_ep: endpoint {
- remote-endpoint = <&csis1_ep>;
- data-lanes = <1>;
- };
- };
-};