diff mbox series

[v6,4/4] arm64: dts: qcom: sc8280xp-x13s: Add bluetooth

Message ID 20230316034759.73489-5-steev@kali.org
State Superseded
Headers show
Series Add WCN6855 Bluetooth support | expand

Commit Message

Steev Klimaszewski March 16, 2023, 3:47 a.m. UTC
The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2,
add this.

Signed-off-by: Steev Klimaszewski <steev@kali.org>
---
Changes since v5:
 * Update patch subject
 * Specify initial mode (via guess) for vreg_s1c
 * Drop uart17 definition
 * Rename bt_en to bt_default because configuring more than one pin
 * Correct (maybe) bias configurations
 * Correct cts gpio
 * Split rts-tx into two nodes
 * Drop incorrect link in the commit message

Changes since v4:
 * Address Konrad's review comments.

Changes since v3:
 * Add vreg_s1c
 * Add regulators and not dead code
 * Fix commit message changelog

Changes since v2:
 * Remove dead code and add TODO comment
 * Make dtbs_check happy with the pin definitions

 .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 80 +++++++++++++++++++
 1 file changed, 80 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
index 53ae75fb52ed..b3221c27903a 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -24,6 +24,7 @@  / {
 	aliases {
 		i2c4 = &i2c4;
 		i2c21 = &i2c21;
+		serial1 = &uart2;
 	};
 
 	wcd938x: audio-codec {
@@ -431,6 +432,16 @@  regulators-1 {
 		qcom,pmic-id = "c";
 		vdd-bob-supply = <&vreg_vph_pwr>;
 
+		vreg_s1c: smps1 {
+			regulator-name = "vreg_s1c";
+			regulator-min-microvolt = <1880000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_AUTO>,
+						  <RPMH_REGULATOR_MODE_RET>;
+			regulator-allow-set-load;
+		};
+
 		vreg_l1c: ldo1 {
 			regulator-name = "vreg_l1c";
 			regulator-min-microvolt = <1800000>;
@@ -901,6 +912,32 @@  &qup0 {
 	status = "okay";
 };
 
+&uart2 {
+	pinctrl-0 = <&uart2_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn6855-bt";
+
+		vddio-supply = <&vreg_s10b>;
+		vddbtcxmx-supply = <&vreg_s12b>;
+		vddrfacmn-supply = <&vreg_s12b>;
+		vddrfa0p8-supply = <&vreg_s12b>;
+		vddrfa1p2-supply = <&vreg_s11b>;
+		vddrfa1p7-supply = <&vreg_s1c>;
+
+		max-speed = <3200000>;
+
+		enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&bt_default>;
+		pinctrl-names = "default";
+	};
+};
+
 &qup1 {
 	status = "okay";
 };
@@ -1175,6 +1212,21 @@  hastings_reg_en: hastings-reg-en-state {
 &tlmm {
 	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
 
+	bt_default: bt-default-state {
+		hstp-sw-ctrl-pins {
+			pins = "gpio132";
+			function = "gpio";
+			bias-pull-down;
+		};
+
+		hstp-bt-en-pins {
+			pins = "gpio133";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
 	edp_reg_en: edp-reg-en-state {
 		pins = "gpio25";
 		function = "gpio";
@@ -1196,6 +1248,34 @@  i2c4_default: i2c4-default-state {
 		bias-disable;
 	};
 
+	uart2_default: uart2-default-state {
+		cts-pins {
+			pins = "gpio121";
+			function = "qup2";
+			bias-pull-down;
+		};
+
+		rts-pins {
+			pins = "gpio122";
+			function = "qup2";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		tx-pins {
+			pins = "gpio123";
+			function = "qup2";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		rx-pins {
+			pins = "gpio124";
+			function = "qup2";
+			bias-pull-up;
+		};
+	};
+
 	i2c21_default: i2c21-default-state {
 		pins = "gpio81", "gpio82";
 		function = "qup21";