diff mbox series

[v2,05/10] ARM: dts: sunxi: h3/h5: Switch dma-names order for snps,dw-apb-uart nodes

Message ID 20230321215624.78383-6-cristian.ciocaltea@collabora.com
State Accepted
Commit bb9ecbee05f5fd0042caf264835fad55a132d8c7
Headers show
Series [v2,01/10] dt-bindings: serial: snps-dw-apb-uart: Switch dma-names order | expand

Commit Message

Cristian Ciocaltea March 21, 2023, 9:56 p.m. UTC
Commit 370f696e4474 ("dt-bindings: serial: snps-dw-apb-uart: add dma &
dma-names properties") documented dma-names property to handle Allwinner
D1 dtbs_check warnings, but relies on the rx->tx ordering, which is the
reverse of what a bunch of different boards expect.

The initial proposed solution was to allow a flexible dma-names order in
the binding, due to potential ABI breakage concerns after fixing the DTS
files. But luckily the Allwinner boards are not affected, since they are
using a shared DMA channel for rx and tx.

Hence, the first step in fixing the inconsistency was to change
dma-names order in the binding to tx->rx.

Do the same for the snps,dw-apb-uart nodes in the DTS file.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
---
 arch/arm/boot/dts/sunxi-h3-h5.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 686193bd6bd9..ade1cd50e445 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -710,7 +710,7 @@  uart0: serial@1c28000 {
 			clocks = <&ccu CLK_BUS_UART0>;
 			resets = <&ccu RST_BUS_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -723,7 +723,7 @@  uart1: serial@1c28400 {
 			clocks = <&ccu CLK_BUS_UART1>;
 			resets = <&ccu RST_BUS_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -736,7 +736,7 @@  uart2: serial@1c28800 {
 			clocks = <&ccu CLK_BUS_UART2>;
 			resets = <&ccu RST_BUS_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -749,7 +749,7 @@  uart3: serial@1c28c00 {
 			clocks = <&ccu CLK_BUS_UART3>;
 			resets = <&ccu RST_BUS_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};