diff mbox series

[v2] wifi: brcmfmac: Fix SDIO suspend/resume regression

Message ID 20230320122252.240070-1-hdegoede@redhat.com
State Superseded
Headers show
Series [v2] wifi: brcmfmac: Fix SDIO suspend/resume regression | expand

Commit Message

Hans de Goede March 20, 2023, 12:22 p.m. UTC
After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on suspend
and then re-probed on resume.

In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
the newly added re-probe on resume fails like this:

 brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
 ieee80211 phy1: brcmf_bus_started: failed: -110
 ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
 brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed

It seems this specific brcmfmac model does not like being reprobed without
it actually being turned off first.

And the adapter is not being turned off during suspend because of
commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
driver").

Now that the driver is being reprobed on resume, the disabling of ACPI
pm is no longer necessary, except when WOWL is used (in which case there
is no-reprobe).

Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
the brcmfmac43430a1 suspend/resume regression and should help save some
power when suspended.

This change means that the code now also may re-enable ACPI pm when WOWL
gets disabled. ACPI pm should only be re-enabled if it was enabled by
the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
to save the original state for this.

This has been tested on the following devices:

Asus T100TA                brcmfmac43241b4-sdio
Acer Iconia One 7 B1-750   brcmfmac43340-sdio
Chuwi Hi8                  brcmfmac43430a0-sdio
Chuwi Hi8                  brcmfmac43430a1-sdio

(the Asus T100TA is the device for which the prohibiting of ACPI pm
 was originally added)

Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
- Drop no longer used "struct device *dev" local variable from
  brcmf_ops_sdio_probe() - Reported-by: kernel test robot <lkp@intel.com>
---
- Note this is a resend of v2 with Kalle Valo/s email address fixed
---
 .../broadcom/brcm80211/brcmfmac/bcmsdh.c      | 36 +++++++++++++------
 .../broadcom/brcm80211/brcmfmac/sdio.h        |  2 ++
 2 files changed, 28 insertions(+), 10 deletions(-)

Comments

Ulf Hansson March 23, 2023, 2:33 p.m. UTC | #1
+ Yann, Christophe

On Mon, 20 Mar 2023 at 13:22, Hans de Goede <hdegoede@redhat.com> wrote:
>
> After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
> unless WOWL is used"), the wifi adapter by default is turned off on suspend
> and then re-probed on resume.
>
> In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
> the newly added re-probe on resume fails like this:
>
>  brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
>  ieee80211 phy1: brcmf_bus_started: failed: -110
>  ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
>  brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
>
> It seems this specific brcmfmac model does not like being reprobed without
> it actually being turned off first.
>
> And the adapter is not being turned off during suspend because of
> commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
> driver").
>
> Now that the driver is being reprobed on resume, the disabling of ACPI
> pm is no longer necessary, except when WOWL is used (in which case there
> is no-reprobe).
>
> Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
> the brcmfmac43430a1 suspend/resume regression and should help save some
> power when suspended.
>
> This change means that the code now also may re-enable ACPI pm when WOWL
> gets disabled. ACPI pm should only be re-enabled if it was enabled by
> the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
> to save the original state for this.
>
> This has been tested on the following devices:
>
> Asus T100TA                brcmfmac43241b4-sdio
> Acer Iconia One 7 B1-750   brcmfmac43340-sdio
> Chuwi Hi8                  brcmfmac43430a0-sdio
> Chuwi Hi8                  brcmfmac43430a1-sdio
>
> (the Asus T100TA is the device for which the prohibiting of ACPI pm
>  was originally added)
>
> Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
> Cc: Ulf Hansson <ulf.hansson@linaro.org>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Seems reasonable to me, thanks for fixing this! Feel free to add:

Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>

Kind regards
Uffe

> ---
> Changes in v2:
> - Drop no longer used "struct device *dev" local variable from
>   brcmf_ops_sdio_probe() - Reported-by: kernel test robot <lkp@intel.com>
> ---
> - Note this is a resend of v2 with Kalle Valo/s email address fixed
> ---
>  .../broadcom/brcm80211/brcmfmac/bcmsdh.c      | 36 +++++++++++++------
>  .../broadcom/brcm80211/brcmfmac/sdio.h        |  2 ++
>  2 files changed, 28 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
> index b7c918f241c9..65d4799a5658 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
> @@ -994,15 +994,34 @@ static const struct sdio_device_id brcmf_sdmmc_ids[] = {
>  MODULE_DEVICE_TABLE(sdio, brcmf_sdmmc_ids);
>
>
> -static void brcmf_sdiod_acpi_set_power_manageable(struct device *dev,
> -                                                 int val)
> +static void brcmf_sdiod_acpi_save_power_manageable(struct brcmf_sdio_dev *sdiodev)
>  {
>  #if IS_ENABLED(CONFIG_ACPI)
>         struct acpi_device *adev;
>
> -       adev = ACPI_COMPANION(dev);
> +       adev = ACPI_COMPANION(&sdiodev->func1->dev);
>         if (adev)
> -               adev->flags.power_manageable = 0;
> +               sdiodev->func1_power_manageable = adev->flags.power_manageable;
> +
> +       adev = ACPI_COMPANION(&sdiodev->func2->dev);
> +       if (adev)
> +               sdiodev->func2_power_manageable = adev->flags.power_manageable;
> +#endif
> +}
> +
> +static void brcmf_sdiod_acpi_set_power_manageable(struct brcmf_sdio_dev *sdiodev,
> +                                                 int enable)
> +{
> +#if IS_ENABLED(CONFIG_ACPI)
> +       struct acpi_device *adev;
> +
> +       adev = ACPI_COMPANION(&sdiodev->func1->dev);
> +       if (adev)
> +               adev->flags.power_manageable = enable ? sdiodev->func1_power_manageable : 0;
> +
> +       adev = ACPI_COMPANION(&sdiodev->func2->dev);
> +       if (adev)
> +               adev->flags.power_manageable = enable ? sdiodev->func2_power_manageable : 0;
>  #endif
>  }
>
> @@ -1012,7 +1031,6 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func,
>         int err;
>         struct brcmf_sdio_dev *sdiodev;
>         struct brcmf_bus *bus_if;
> -       struct device *dev;
>
>         brcmf_dbg(SDIO, "Enter\n");
>         brcmf_dbg(SDIO, "Class=%x\n", func->class);
> @@ -1020,14 +1038,9 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func,
>         brcmf_dbg(SDIO, "sdio device ID: 0x%04x\n", func->device);
>         brcmf_dbg(SDIO, "Function#: %d\n", func->num);
>
> -       dev = &func->dev;
> -
>         /* Set MMC_QUIRK_LENIENT_FN0 for this card */
>         func->card->quirks |= MMC_QUIRK_LENIENT_FN0;
>
> -       /* prohibit ACPI power management for this device */
> -       brcmf_sdiod_acpi_set_power_manageable(dev, 0);
> -
>         /* Consume func num 1 but dont do anything with it. */
>         if (func->num == 1)
>                 return 0;
> @@ -1059,6 +1072,7 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func,
>         dev_set_drvdata(&sdiodev->func1->dev, bus_if);
>         sdiodev->dev = &sdiodev->func1->dev;
>
> +       brcmf_sdiod_acpi_save_power_manageable(sdiodev);
>         brcmf_sdiod_change_state(sdiodev, BRCMF_SDIOD_DOWN);
>
>         brcmf_dbg(SDIO, "F2 found, calling brcmf_sdiod_probe...\n");
> @@ -1124,6 +1138,8 @@ void brcmf_sdio_wowl_config(struct device *dev, bool enabled)
>
>         if (sdiodev->settings->bus.sdio.oob_irq_supported ||
>             pm_caps & MMC_PM_WAKE_SDIO_IRQ) {
> +               /* Stop ACPI from turning off the device when wowl is enabled */
> +               brcmf_sdiod_acpi_set_power_manageable(sdiodev, !enabled);
>                 sdiodev->wowl_enabled = enabled;
>                 brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
>                 return;
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
> index b76d34d36bde..0d18ed15b403 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
> @@ -188,6 +188,8 @@ struct brcmf_sdio_dev {
>         char nvram_name[BRCMF_FW_NAME_LEN];
>         char clm_name[BRCMF_FW_NAME_LEN];
>         bool wowl_enabled;
> +       bool func1_power_manageable;
> +       bool func2_power_manageable;
>         enum brcmf_sdiod_state state;
>         struct brcmf_sdiod_freezer *freezer;
>         const struct firmware *clm_fw;
> --
> 2.39.1
>
Kalle Valo March 24, 2023, 7:11 a.m. UTC | #2
Ulf Hansson <ulf.hansson@linaro.org> writes:

> + Yann, Christophe
>
> On Mon, 20 Mar 2023 at 13:22, Hans de Goede <hdegoede@redhat.com> wrote:
>>
>> After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
>> unless WOWL is used"), the wifi adapter by default is turned off on suspend
>> and then re-probed on resume.
>>
>> In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
>> the newly added re-probe on resume fails like this:
>>
>>  brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
>>  ieee80211 phy1: brcmf_bus_started: failed: -110
>>  ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
>>  brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
>>
>> It seems this specific brcmfmac model does not like being reprobed without
>> it actually being turned off first.
>>
>> And the adapter is not being turned off during suspend because of
>> commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
>> driver").
>>
>> Now that the driver is being reprobed on resume, the disabling of ACPI
>> pm is no longer necessary, except when WOWL is used (in which case there
>> is no-reprobe).
>>
>> Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
>> the brcmfmac43430a1 suspend/resume regression and should help save some
>> power when suspended.
>>
>> This change means that the code now also may re-enable ACPI pm when WOWL
>> gets disabled. ACPI pm should only be re-enabled if it was enabled by
>> the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
>> to save the original state for this.
>>
>> This has been tested on the following devices:
>>
>> Asus T100TA                brcmfmac43241b4-sdio
>> Acer Iconia One 7 B1-750   brcmfmac43340-sdio
>> Chuwi Hi8                  brcmfmac43430a0-sdio
>> Chuwi Hi8                  brcmfmac43430a1-sdio
>>
>> (the Asus T100TA is the device for which the prohibiting of ACPI pm
>>  was originally added)
>>
>> Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
>> Cc: Ulf Hansson <ulf.hansson@linaro.org>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>
> Seems reasonable to me, thanks for fixing this! Feel free to add:
>
> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>

As this is an older regression from v5.19 should I take this to
wireless-next to get more testing time?
Hans de Goede March 24, 2023, 7:43 a.m. UTC | #3
Hi Kalle,

On 3/24/23 08:11, Kalle Valo wrote:
> Ulf Hansson <ulf.hansson@linaro.org> writes:
> 
>> + Yann, Christophe
>>
>> On Mon, 20 Mar 2023 at 13:22, Hans de Goede <hdegoede@redhat.com> wrote:
>>>
>>> After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
>>> unless WOWL is used"), the wifi adapter by default is turned off on suspend
>>> and then re-probed on resume.
>>>
>>> In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
>>> the newly added re-probe on resume fails like this:
>>>
>>>  brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
>>>  ieee80211 phy1: brcmf_bus_started: failed: -110
>>>  ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
>>>  brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
>>>
>>> It seems this specific brcmfmac model does not like being reprobed without
>>> it actually being turned off first.
>>>
>>> And the adapter is not being turned off during suspend because of
>>> commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
>>> driver").
>>>
>>> Now that the driver is being reprobed on resume, the disabling of ACPI
>>> pm is no longer necessary, except when WOWL is used (in which case there
>>> is no-reprobe).
>>>
>>> Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
>>> the brcmfmac43430a1 suspend/resume regression and should help save some
>>> power when suspended.
>>>
>>> This change means that the code now also may re-enable ACPI pm when WOWL
>>> gets disabled. ACPI pm should only be re-enabled if it was enabled by
>>> the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
>>> to save the original state for this.
>>>
>>> This has been tested on the following devices:
>>>
>>> Asus T100TA                brcmfmac43241b4-sdio
>>> Acer Iconia One 7 B1-750   brcmfmac43340-sdio
>>> Chuwi Hi8                  brcmfmac43430a0-sdio
>>> Chuwi Hi8                  brcmfmac43430a1-sdio
>>>
>>> (the Asus T100TA is the device for which the prohibiting of ACPI pm
>>>  was originally added)
>>>
>>> Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
>>> Cc: Ulf Hansson <ulf.hansson@linaro.org>
>>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>>
>> Seems reasonable to me, thanks for fixing this! Feel free to add:
>>
>> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
> 
> As this is an older regression from v5.19 should I take this to
> wireless-next to get more testing time?

AFAIK the only ACPI platforms (which this patch impacts) these SDIO wifi modules are used on are x86  Bay Trail and Cherry Trail SoCs, such as the list of _4_ devices I have tested on and it does fix a real regression.

Even though this is a somewhat older regression my personal preference would be for this to get send to Linus sooner rather then later so that this regression gets fixed.

Regards,

Hans
Yann Gautier March 24, 2023, 8:12 a.m. UTC | #4
On 3/23/23 15:33, Ulf Hansson wrote:
> + Yann, Christophe
> 

Hi Ulf,

Thanks for the forward!
The patch only changes code under CONFIG_ACPI, which isn't enabled on 
Arm platforms. So no impact for STM32MP1 on which we saw the first 
issue, and for which you made the ("brcmfmac: Avoid keeping power to 
SDIO card unless WOWL is used") patch.


Best regards,
Yann

> On Mon, 20 Mar 2023 at 13:22, Hans de Goede <hdegoede@redhat.com> wrote:
>>
>> After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
>> unless WOWL is used"), the wifi adapter by default is turned off on suspend
>> and then re-probed on resume.
>>
>> In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
>> the newly added re-probe on resume fails like this:
>>
>>   brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
>>   ieee80211 phy1: brcmf_bus_started: failed: -110
>>   ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
>>   brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
>>
>> It seems this specific brcmfmac model does not like being reprobed without
>> it actually being turned off first.
>>
>> And the adapter is not being turned off during suspend because of
>> commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
>> driver").
>>
>> Now that the driver is being reprobed on resume, the disabling of ACPI
>> pm is no longer necessary, except when WOWL is used (in which case there
>> is no-reprobe).
>>
>> Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
>> the brcmfmac43430a1 suspend/resume regression and should help save some
>> power when suspended.
>>
>> This change means that the code now also may re-enable ACPI pm when WOWL
>> gets disabled. ACPI pm should only be re-enabled if it was enabled by
>> the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
>> to save the original state for this.
>>
>> This has been tested on the following devices:
>>
>> Asus T100TA                brcmfmac43241b4-sdio
>> Acer Iconia One 7 B1-750   brcmfmac43340-sdio
>> Chuwi Hi8                  brcmfmac43430a0-sdio
>> Chuwi Hi8                  brcmfmac43430a1-sdio
>>
>> (the Asus T100TA is the device for which the prohibiting of ACPI pm
>>   was originally added)
>>
>> Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
>> Cc: Ulf Hansson <ulf.hansson@linaro.org>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> 
> Seems reasonable to me, thanks for fixing this! Feel free to add:
> 
> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
> 
> Kind regards
> Uffe
> 
>> ---
>> Changes in v2:
>> - Drop no longer used "struct device *dev" local variable from
>>    brcmf_ops_sdio_probe() - Reported-by: kernel test robot <lkp@intel.com>
>> ---
>> - Note this is a resend of v2 with Kalle Valo/s email address fixed
>> ---
>>   .../broadcom/brcm80211/brcmfmac/bcmsdh.c      | 36 +++++++++++++------
>>   .../broadcom/brcm80211/brcmfmac/sdio.h        |  2 ++
>>   2 files changed, 28 insertions(+), 10 deletions(-)
>>
>> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
>> index b7c918f241c9..65d4799a5658 100644
>> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
>> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
>> @@ -994,15 +994,34 @@ static const struct sdio_device_id brcmf_sdmmc_ids[] = {
>>   MODULE_DEVICE_TABLE(sdio, brcmf_sdmmc_ids);
>>
>>
>> -static void brcmf_sdiod_acpi_set_power_manageable(struct device *dev,
>> -                                                 int val)
>> +static void brcmf_sdiod_acpi_save_power_manageable(struct brcmf_sdio_dev *sdiodev)
>>   {
>>   #if IS_ENABLED(CONFIG_ACPI)
>>          struct acpi_device *adev;
>>
>> -       adev = ACPI_COMPANION(dev);
>> +       adev = ACPI_COMPANION(&sdiodev->func1->dev);
>>          if (adev)
>> -               adev->flags.power_manageable = 0;
>> +               sdiodev->func1_power_manageable = adev->flags.power_manageable;
>> +
>> +       adev = ACPI_COMPANION(&sdiodev->func2->dev);
>> +       if (adev)
>> +               sdiodev->func2_power_manageable = adev->flags.power_manageable;
>> +#endif
>> +}
>> +
>> +static void brcmf_sdiod_acpi_set_power_manageable(struct brcmf_sdio_dev *sdiodev,
>> +                                                 int enable)
>> +{
>> +#if IS_ENABLED(CONFIG_ACPI)
>> +       struct acpi_device *adev;
>> +
>> +       adev = ACPI_COMPANION(&sdiodev->func1->dev);
>> +       if (adev)
>> +               adev->flags.power_manageable = enable ? sdiodev->func1_power_manageable : 0;
>> +
>> +       adev = ACPI_COMPANION(&sdiodev->func2->dev);
>> +       if (adev)
>> +               adev->flags.power_manageable = enable ? sdiodev->func2_power_manageable : 0;
>>   #endif
>>   }
>>
>> @@ -1012,7 +1031,6 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func,
>>          int err;
>>          struct brcmf_sdio_dev *sdiodev;
>>          struct brcmf_bus *bus_if;
>> -       struct device *dev;
>>
>>          brcmf_dbg(SDIO, "Enter\n");
>>          brcmf_dbg(SDIO, "Class=%x\n", func->class);
>> @@ -1020,14 +1038,9 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func,
>>          brcmf_dbg(SDIO, "sdio device ID: 0x%04x\n", func->device);
>>          brcmf_dbg(SDIO, "Function#: %d\n", func->num);
>>
>> -       dev = &func->dev;
>> -
>>          /* Set MMC_QUIRK_LENIENT_FN0 for this card */
>>          func->card->quirks |= MMC_QUIRK_LENIENT_FN0;
>>
>> -       /* prohibit ACPI power management for this device */
>> -       brcmf_sdiod_acpi_set_power_manageable(dev, 0);
>> -
>>          /* Consume func num 1 but dont do anything with it. */
>>          if (func->num == 1)
>>                  return 0;
>> @@ -1059,6 +1072,7 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func,
>>          dev_set_drvdata(&sdiodev->func1->dev, bus_if);
>>          sdiodev->dev = &sdiodev->func1->dev;
>>
>> +       brcmf_sdiod_acpi_save_power_manageable(sdiodev);
>>          brcmf_sdiod_change_state(sdiodev, BRCMF_SDIOD_DOWN);
>>
>>          brcmf_dbg(SDIO, "F2 found, calling brcmf_sdiod_probe...\n");
>> @@ -1124,6 +1138,8 @@ void brcmf_sdio_wowl_config(struct device *dev, bool enabled)
>>
>>          if (sdiodev->settings->bus.sdio.oob_irq_supported ||
>>              pm_caps & MMC_PM_WAKE_SDIO_IRQ) {
>> +               /* Stop ACPI from turning off the device when wowl is enabled */
>> +               brcmf_sdiod_acpi_set_power_manageable(sdiodev, !enabled);
>>                  sdiodev->wowl_enabled = enabled;
>>                  brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
>>                  return;
>> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
>> index b76d34d36bde..0d18ed15b403 100644
>> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
>> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
>> @@ -188,6 +188,8 @@ struct brcmf_sdio_dev {
>>          char nvram_name[BRCMF_FW_NAME_LEN];
>>          char clm_name[BRCMF_FW_NAME_LEN];
>>          bool wowl_enabled;
>> +       bool func1_power_manageable;
>> +       bool func2_power_manageable;
>>          enum brcmf_sdiod_state state;
>>          struct brcmf_sdiod_freezer *freezer;
>>          const struct firmware *clm_fw;
>> --
>> 2.39.1
>>
Kalle Valo March 31, 2023, 3 p.m. UTC | #5
Hans de Goede <hdegoede@redhat.com> wrote:

> After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
> unless WOWL is used"), the wifi adapter by default is turned off on suspend
> and then re-probed on resume.
> 
> In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
> the newly added re-probe on resume fails like this:
> 
>  brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
>  ieee80211 phy1: brcmf_bus_started: failed: -110
>  ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
>  brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
> 
> It seems this specific brcmfmac model does not like being reprobed without
> it actually being turned off first.
> 
> And the adapter is not being turned off during suspend because of
> commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
> driver").
> 
> Now that the driver is being reprobed on resume, the disabling of ACPI
> pm is no longer necessary, except when WOWL is used (in which case there
> is no-reprobe).
> 
> Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
> the brcmfmac43430a1 suspend/resume regression and should help save some
> power when suspended.
> 
> This change means that the code now also may re-enable ACPI pm when WOWL
> gets disabled. ACPI pm should only be re-enabled if it was enabled by
> the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
> to save the original state for this.
> 
> This has been tested on the following devices:
> 
> Asus T100TA                brcmfmac43241b4-sdio
> Acer Iconia One 7 B1-750   brcmfmac43340-sdio
> Chuwi Hi8                  brcmfmac43430a0-sdio
> Chuwi Hi8                  brcmfmac43430a1-sdio
> 
> (the Asus T100TA is the device for which the prohibiting of ACPI pm
>  was originally added)
> 
> Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used")
> Cc: Ulf Hansson <ulf.hansson@linaro.org>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>

Patch applied to wireless.git, thanks.

e4efa515d58f wifi: brcmfmac: Fix SDIO suspend/resume regression
diff mbox series

Patch

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
index b7c918f241c9..65d4799a5658 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c
@@ -994,15 +994,34 @@  static const struct sdio_device_id brcmf_sdmmc_ids[] = {
 MODULE_DEVICE_TABLE(sdio, brcmf_sdmmc_ids);
 
 
-static void brcmf_sdiod_acpi_set_power_manageable(struct device *dev,
-						  int val)
+static void brcmf_sdiod_acpi_save_power_manageable(struct brcmf_sdio_dev *sdiodev)
 {
 #if IS_ENABLED(CONFIG_ACPI)
 	struct acpi_device *adev;
 
-	adev = ACPI_COMPANION(dev);
+	adev = ACPI_COMPANION(&sdiodev->func1->dev);
 	if (adev)
-		adev->flags.power_manageable = 0;
+		sdiodev->func1_power_manageable = adev->flags.power_manageable;
+
+	adev = ACPI_COMPANION(&sdiodev->func2->dev);
+	if (adev)
+		sdiodev->func2_power_manageable = adev->flags.power_manageable;
+#endif
+}
+
+static void brcmf_sdiod_acpi_set_power_manageable(struct brcmf_sdio_dev *sdiodev,
+						  int enable)
+{
+#if IS_ENABLED(CONFIG_ACPI)
+	struct acpi_device *adev;
+
+	adev = ACPI_COMPANION(&sdiodev->func1->dev);
+	if (adev)
+		adev->flags.power_manageable = enable ? sdiodev->func1_power_manageable : 0;
+
+	adev = ACPI_COMPANION(&sdiodev->func2->dev);
+	if (adev)
+		adev->flags.power_manageable = enable ? sdiodev->func2_power_manageable : 0;
 #endif
 }
 
@@ -1012,7 +1031,6 @@  static int brcmf_ops_sdio_probe(struct sdio_func *func,
 	int err;
 	struct brcmf_sdio_dev *sdiodev;
 	struct brcmf_bus *bus_if;
-	struct device *dev;
 
 	brcmf_dbg(SDIO, "Enter\n");
 	brcmf_dbg(SDIO, "Class=%x\n", func->class);
@@ -1020,14 +1038,9 @@  static int brcmf_ops_sdio_probe(struct sdio_func *func,
 	brcmf_dbg(SDIO, "sdio device ID: 0x%04x\n", func->device);
 	brcmf_dbg(SDIO, "Function#: %d\n", func->num);
 
-	dev = &func->dev;
-
 	/* Set MMC_QUIRK_LENIENT_FN0 for this card */
 	func->card->quirks |= MMC_QUIRK_LENIENT_FN0;
 
-	/* prohibit ACPI power management for this device */
-	brcmf_sdiod_acpi_set_power_manageable(dev, 0);
-
 	/* Consume func num 1 but dont do anything with it. */
 	if (func->num == 1)
 		return 0;
@@ -1059,6 +1072,7 @@  static int brcmf_ops_sdio_probe(struct sdio_func *func,
 	dev_set_drvdata(&sdiodev->func1->dev, bus_if);
 	sdiodev->dev = &sdiodev->func1->dev;
 
+	brcmf_sdiod_acpi_save_power_manageable(sdiodev);
 	brcmf_sdiod_change_state(sdiodev, BRCMF_SDIOD_DOWN);
 
 	brcmf_dbg(SDIO, "F2 found, calling brcmf_sdiod_probe...\n");
@@ -1124,6 +1138,8 @@  void brcmf_sdio_wowl_config(struct device *dev, bool enabled)
 
 	if (sdiodev->settings->bus.sdio.oob_irq_supported ||
 	    pm_caps & MMC_PM_WAKE_SDIO_IRQ) {
+		/* Stop ACPI from turning off the device when wowl is enabled */
+		brcmf_sdiod_acpi_set_power_manageable(sdiodev, !enabled);
 		sdiodev->wowl_enabled = enabled;
 		brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
 		return;
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
index b76d34d36bde..0d18ed15b403 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h
@@ -188,6 +188,8 @@  struct brcmf_sdio_dev {
 	char nvram_name[BRCMF_FW_NAME_LEN];
 	char clm_name[BRCMF_FW_NAME_LEN];
 	bool wowl_enabled;
+	bool func1_power_manageable;
+	bool func2_power_manageable;
 	enum brcmf_sdiod_state state;
 	struct brcmf_sdiod_freezer *freezer;
 	const struct firmware *clm_fw;