| Message ID | 20230327125316.210812-15-brgl@bgdev.pl |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: qcom: sa8775p: add basic PMIC support | expand |
On 27.03.2023 14:53, Bartosz Golaszewski wrote: > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > Add GPIO controller nodes to PMICs that have the GPIO hooked up on > sa8775p-ride. > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 40 +++++++++++++++++++++ > 1 file changed, 40 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > index be12997a080c..7602cca47bae 100644 > --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi > @@ -125,6 +125,16 @@ pmm8654au_0_pon_resin: resin { > status = "disabled"; > }; > }; > + > + pmm8654au_0_gpios: gpio@8800 { > + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmm8654au_0_gpios 0 0 12>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > }; > > pmm8654au_1: pmic@2 { > @@ -139,6 +149,16 @@ pmm8654au_1_temp_alarm: temp-alarm@a00 { > interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > #thermal-sensor-cells = <0>; > }; > + > + pmm8654au_1_gpios: gpio@8800 { > + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmm8654au_2_gpios 0 0 12>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > }; > > pmm8654au_2: pmic@4 { > @@ -153,6 +173,16 @@ pmm8654au_2_temp_alarm: temp-alarm@a00 { > interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > #thermal-sensor-cells = <0>; > }; > + > + pmm8654au_2_gpios: gpio@8800 { > + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmm8654au_2_gpios 0 0 12>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > }; > > pmm8654au_3: pmic@6 { > @@ -167,5 +197,15 @@ pmm8654au_3_temp_alarm: temp-alarm@a00 { > interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > #thermal-sensor-cells = <0>; > }; > + > + pmm8654au_3_gpios: gpio@8800 { > + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmm8654au_3_gpios 0 0 12>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > }; > };
diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi index be12997a080c..7602cca47bae 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi @@ -125,6 +125,16 @@ pmm8654au_0_pon_resin: resin { status = "disabled"; }; }; + + pmm8654au_0_gpios: gpio@8800 { + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmm8654au_0_gpios 0 0 12>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; pmm8654au_1: pmic@2 { @@ -139,6 +149,16 @@ pmm8654au_1_temp_alarm: temp-alarm@a00 { interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; + + pmm8654au_1_gpios: gpio@8800 { + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmm8654au_2_gpios 0 0 12>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; pmm8654au_2: pmic@4 { @@ -153,6 +173,16 @@ pmm8654au_2_temp_alarm: temp-alarm@a00 { interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; + + pmm8654au_2_gpios: gpio@8800 { + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmm8654au_2_gpios 0 0 12>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; pmm8654au_3: pmic@6 { @@ -167,5 +197,15 @@ pmm8654au_3_temp_alarm: temp-alarm@a00 { interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; + + pmm8654au_3_gpios: gpio@8800 { + compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmm8654au_3_gpios 0 0 12>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; };