diff mbox series

[v8,2/5] arm64: dts: qcom: Add msm8939 SoC

Message ID 20230330153222.2875121-3-bryan.odonoghue@linaro.org
State Superseded
Headers show
Series Add MSM8939 SoC support with two devices | expand

Commit Message

Bryan O'Donoghue March 30, 2023, 3:32 p.m. UTC
Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
differences to msm8916.

- big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
- DRAM 1x800 LPDDR3
- Camera 4+4 lane CSI
- Venus @ 1080p60 HEVC
- DSI x 2
- Adreno A405
- WiFi wcn3660/wcn3680b 802.11ac

Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Co-developed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Co-developed-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Benjamin Li <benl@squareup.com>
Co-developed-by: James Willcox <jwillcox@squareup.com>
Signed-off-by: James Willcox <jwillcox@squareup.com>
Co-developed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Co-developed-by: Joseph Gates <jgates@squareup.com>
Signed-off-by: Joseph Gates <jgates@squareup.com>
Co-developed-by: Max Chen <mchen@squareup.com>
Signed-off-by: Max Chen <mchen@squareup.com>
Co-developed-by: Zac Crosby <zac@squareup.com>
Signed-off-by: Zac Crosby <zac@squareup.com>
Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio ,konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/msm8939.dtsi | 2454 +++++++++++++++++++++++++
 1 file changed, 2454 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi

Comments

Stephan Gerhold April 6, 2023, 4:46 p.m. UTC | #1
On Thu, Mar 30, 2023 at 04:32:19PM +0100, Bryan O'Donoghue wrote:
> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
> differences to msm8916.
> 
> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
> - DRAM 1x800 LPDDR3
> - Camera 4+4 lane CSI
> - Venus @ 1080p60 HEVC
> - DSI x 2
> - Adreno A405
> - WiFi wcn3660/wcn3680b 802.11ac
> [...]
> ---
>  arch/arm64/boot/dts/qcom/msm8939.dtsi | 2454 +++++++++++++++++++++++++
>  1 file changed, 2454 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> new file mode 100644
> index 0000000000000..96b25dfc4d3f1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> @@ -0,0 +1,2454 @@
> [...]
> +		tsens: thermal-sensor@4a9000 {
> +			compatible = "qcom,msm8939-tsens", "qcom,tsens-v0_1";
> +			reg = <0x004a9000 0x1000>, /* TM */
> +			      <0x004a8000 0x1000>; /* SROT */
> +			nvmem-cells = <&tsens_mode>,
> +				      <&tsens_base1>, <&tsens_base2>,
> +				      <&tsens_s0_p1>, <&tsens_s0_p2>,
> +				      <&tsens_s1_p1>, <&tsens_s1_p2>,
> +				      <&tsens_s2_p1>, <&tsens_s2_p2>,
> +				      <&tsens_s3_p1>, <&tsens_s3_p2>,
> +				      <&tsens_s4_p1>, <&tsens_s4_p2>,
> +				      <&tsens_s4_p1>, <&tsens_s4_p2>,
> +				      <&tsens_s5_p1>, <&tsens_s5_p2>,
> +				      <&tsens_s6_p1>, <&tsens_s6_p2>,
> +				      <&tsens_s7_p1>, <&tsens_s7_p2>,
> +				      <&tsens_s8_p1>, <&tsens_s8_p2>;
> +			nvmem-cell-names = "mode",
> +					   "base1", "base2",
> +					   "s0_p1", "s0_p2",
> +					   "s1_p1", "s1_p2",
> +					   "s2_p1", "s2_p2",
> +					   "s3_p1", "s3_p2",
> +					   "s4_p1", "s4_p2",
> +					   "s4_p1", "s4_p2",

I know you're working on this already so just for completeness:

We discussed in the chat that there should be no s4 here at all since
sensor hwid=4 is not used on MSM8939. I think all the definitions are
already correct so you just need to rename s4 -> s5, s5 -> s6, s6 -> s7,
s8 -> s9.

> +					   "s5_p1", "s5_p2",
> +					   "s6_p1", "s6_p2",
> +					   "s7_p1", "s7_p2",
> +					   "s8_p1", "s8_p2";
> +			#qcom,sensors = <9>;
> +			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "uplow";
> +			#thermal-sensor-cells = <1>;
> +		};
> [...]
> +		pronto: remoteproc@a204000 {
> +			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
> +			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog",
> +					  "fatal",
> +					  "ready",
> +					  "handover",
> +					  "stop-ack";
> +			reg = <0x0a204000 0x2000>,
> +			      <0x0a202000 0x1000>,
> +			      <0x0a21b000 0x3000>;
> +			reg-names = "ccu", "dxe", "pmu";
> +
> +			memory-region = <&wcnss_mem>;
> +
> +			power-domains = <&rpmpd MSM8939_VDDCX>,
> +					<&rpmpd MSM8939_VDDMX>;
> +			power-domain-names = "cx", "mx";
> +
> +			qcom,smem-states = <&wcnss_smp2p_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&wcnss_pin_a>;
> +
> +			status = "disabled";
> +
> +			iris {
> +				compatible = "qcom,wcn3620";
> +				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
> +				clock-names = "xo";
> +			};

Since it looks like another version is needed to fix the tsens problem,
I'd appreciate if you squash in the following diffs for consistency with
my WCNSS compatible change for 8916: Could also send it as follow-up
later though.

Thanks,
Stephan

diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
index 5f68925434c8..e75ee34cb014 100644
--- a/arch/arm64/boot/dts/qcom/apq8039-t2.dts
+++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
@@ -147,14 +147,6 @@ &pm8916_gpios {
 		"PM_GPIO4";
 };
 
-&pronto {
-	status = "okay";
-
-	iris {
-		compatible = "qcom,wcn3680";
-	};
-};
-
 &smd_rpm_regulators {
 	vdd_l1_l2_l3-supply = <&pm8916_s3>;
 	vdd_l4_l5_l6-supply = <&pm8916_s4>;
@@ -490,3 +482,11 @@ &wcd_codec {
 	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
 	status = "okay";
 };
+
+&wcnss {
+	status = "okay";
+};
+
+&wcnss_iris {
+	compatible = "qcom,wcn3680";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts b/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
index cb47bb2413a7..89cceb0c4960 100644
--- a/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
+++ b/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
@@ -51,14 +51,6 @@ usb_id_default: usb-id-default-state {
 	};
 };
 
-&pronto {
-	status = "okay";
-
-	iris {
-		compatible = "qcom,wcn3660";
-	};
-};
-
 &smd_rpm_regulators {
 	vdd_l1_l2_l3-supply = <&pm8916_s3>;
 	vdd_l4_l5_l6-supply = <&pm8916_s4>;
@@ -182,3 +174,11 @@ &usb {
 &usb_hs_phy {
 	extcon = <&usb_id>;
 };
+
+&wcnss {
+	status = "okay";
+};
+
+&wcnss_iris {
+	compatible = "qcom,wcn3660";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
index 96b25dfc4d3f..c15ff24abd30 100644
--- a/arch/arm64/boot/dts/qcom/msm8939.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
@@ -1955,7 +1955,7 @@ usb_hs_phy: phy {
 			};
 		};
 
-		pronto: remoteproc@a204000 {
+		wcnss: remoteproc@a204000 {
 			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
 			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
 					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
@@ -1986,8 +1986,8 @@ pronto: remoteproc@a204000 {
 
 			status = "disabled";
 
-			iris {
-				compatible = "qcom,wcn3620";
+			wcnss_iris: iris {
+				/* Separate chip, compatible is board-specific */
 				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
 				clock-names = "xo";
 			};
@@ -2004,13 +2004,13 @@ wcnss {
 					compatible = "qcom,wcnss";
 					qcom,smd-channels = "WCNSS_CTRL";
 
-					qcom,mmio = <&pronto>;
+					qcom,mmio = <&wcnss>;
 
-					bluetooth {
+					wcnss_bt: bluetooth {
 						compatible = "qcom,wcnss-bt";
 					};
 
-					wifi {
+					wcnss_wifi: wifi {
 						compatible = "qcom,wcnss-wlan";
 
 						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
new file mode 100644
index 0000000000000..96b25dfc4d3f1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
@@ -0,0 +1,2454 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2023, Linaro Limited
+ */
+
+#include <dt-bindings/clock/qcom,gcc-msm8939.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interconnect/qcom,msm8939.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8939.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	/*
+	 * Stock LK wants address-cells/size-cells = 2
+	 * A number of our drivers want address/size cells = 1
+	 * hence the disparity between top-level and /soc below.
+	 */
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@100 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x100>;
+			next-level-cache = <&L2_1>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs1_mbox>;
+			#cooling-cells = <2>;
+			L2_1: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+			};
+		};
+
+		CPU1: cpu@101 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x101>;
+			next-level-cache = <&L2_1>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs1_mbox>;
+			#cooling-cells = <2>;
+		};
+
+		CPU2: cpu@102 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x102>;
+			next-level-cache = <&L2_1>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs1_mbox>;
+			#cooling-cells = <2>;
+		};
+
+		CPU3: cpu@103 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x103>;
+			next-level-cache = <&L2_1>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs1_mbox>;
+			#cooling-cells = <2>;
+		};
+
+		CPU4: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x0>;
+			qcom,acc = <&acc4>;
+			qcom,saw = <&saw4>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs0_mbox>;
+			#cooling-cells = <2>;
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+			};
+		};
+
+		CPU5: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			qcom,acc = <&acc5>;
+			qcom,saw = <&saw5>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs0_mbox>;
+			#cooling-cells = <2>;
+		};
+
+		CPU6: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			qcom,acc = <&acc6>;
+			qcom,saw = <&saw6>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs0_mbox>;
+			#cooling-cells = <2>;
+		};
+
+		CPU7: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			enable-method = "spin-table";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			qcom,acc = <&acc7>;
+			qcom,saw = <&saw7>;
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&apcs0_mbox>;
+			#cooling-cells = <2>;
+		};
+
+		idle-states {
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible ="qcom,idle-state-spc", "arm,idle-state";
+				entry-latency-us = <130>;
+				exit-latency-us = <150>;
+				min-residency-us = <2000>;
+				local-timer-stop;
+			};
+		};
+	};
+
+	/*
+	 * MSM8939 has a big.LITTLE heterogeneous computing architecture,
+	 * consisting of two clusters of four ARM Cortex-A53s each. The
+	 * LITTLE cluster runs at 1.0-1.2GHz, and the big cluster runs
+	 * at 1.5-1.7GHz.
+	 *
+	 * The enable method used here is spin-table which presupposes use
+	 * of a 2nd stage boot shim such as lk2nd to have installed a
+	 * spin-table, the downstream non-psci/non-spin-table method that
+	 * default msm8916/msm8936/msm8939 will not be supported upstream.
+	 */
+	cpu-map {
+		/* LITTLE (efficiency) cluster */
+		cluster0 {
+			core0 {
+				cpu = <&CPU4>;
+			};
+
+			core1 {
+				cpu = <&CPU5>;
+			};
+
+			core2 {
+				cpu = <&CPU6>;
+			};
+
+			core3 {
+				cpu = <&CPU7>;
+			};
+		};
+
+		/* big (performance) cluster */
+		/* Boot CPU is cluster 1 core 0 */
+		cluster1 {
+			core0 {
+				cpu = <&CPU0>;
+			};
+
+			core1 {
+				cpu = <&CPU1>;
+			};
+
+			core2 {
+				cpu = <&CPU2>;
+			};
+
+			core3 {
+				cpu = <&CPU3>;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-msm8916", "qcom,scm";
+			clocks = <&gcc GCC_CRYPTO_CLK>,
+				 <&gcc GCC_CRYPTO_AXI_CLK>,
+				 <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+			#reset-cells = <1>;
+
+			qcom,dload-mode = <&tcsr 0x6100>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tz-apps@86000000 {
+			reg = <0x0 0x86000000 0x0 0x300000>;
+			no-map;
+		};
+
+		smem@86300000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x86300000 0x0 0x100000>;
+			no-map;
+
+			hwlocks = <&tcsr_mutex 3>;
+			qcom,rpm-msg-ram = <&rpm_msg_ram>;
+		};
+
+		hypervisor@86400000 {
+			reg = <0x0 0x86400000 0x0 0x100000>;
+			no-map;
+		};
+
+		tz@86500000 {
+			reg = <0x0 0x86500000 0x0 0x180000>;
+			no-map;
+		};
+
+		reserved@86680000 {
+			reg = <0x0 0x86680000 0x0 0x80000>;
+			no-map;
+		};
+
+		rmtfs@86700000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0x86700000 0x0 0xe0000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+
+		rfsa@867e0000 {
+			reg = <0x0 0x867e0000 0x0 0x20000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@86800000 {
+			reg = <0x0 0x86800000 0x0 0x5500000>;
+			no-map;
+		};
+
+		wcnss_mem: wcnss@8bd00000 {
+			reg = <0x0 0x8bd00000 0x0 0x600000>;
+			no-map;
+		};
+
+		venus_mem: venus@8c300000 {
+			reg = <0x0 0x8c300000 0x0 0x800000>;
+			no-map;
+		};
+
+		mba_mem: mba@8cb00000 {
+			reg = <0x0 0x8cb00000 0x0 0x100000>;
+			no-map;
+		};
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs1_mbox 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8936";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8936", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clock-names = "xo";
+					clocks = <&xo_board>;
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8939-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <1>;
+						};
+
+						rpmpd_opp_svs_krait: opp2 {
+							opp-level = <2>;
+						};
+
+						rpmpd_opp_svs_soc: opp3 {
+							opp-level = <3>;
+						};
+
+						rpmpd_opp_nom: opp4 {
+							opp-level = <4>;
+						};
+
+						rpmpd_opp_turbo: opp5 {
+							opp-level = <5>;
+						};
+
+						rpmpd_opp_super_turbo: opp6 {
+							opp-level = <6>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	smp2p-hexagon {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs1_mbox 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		hexagon_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+		};
+	};
+
+	smp2p-wcnss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs1_mbox 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs1_mbox 8 13>;
+		qcom,ipc-3 = <&apcs1_mbox 8 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smsm: hexagon@1 {
+			reg = <1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@6 {
+			reg = <6>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xffffffff>;
+
+		rng@22000 {
+			compatible = "qcom,prng";
+			reg = <0x00022000 0x200>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		qfprom: qfprom@5c000 {
+			compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
+			reg = <0x0005c000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@a0 {
+				reg = <0xa0 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s5_p1: s5-p1@a1 {
+				reg = <0xa1 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p2: s5-p2@a1 {
+				reg = <0xa1 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@a2 {
+				reg = <0xa2 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s6_p2: s6-p2@a3 {
+				reg = <0xa3 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s7_p1: s7-p1@a4 {
+				reg = <0xa4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@a4 {
+				reg = <0xa4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p1: s8-p1@a5 {
+				reg = <0xa5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s8_p2: s8-p2@a6 {
+				reg = <0xa6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_base2: base2@a7 {
+				reg = <0xa7 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_mode: mode@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 3>;
+			};
+
+			tsens_s0_p1: s0-p1@d0 {
+				reg = <0xd0 0x2>;
+				bits = <3 6>;
+			};
+
+			tsens_s0_p2: s0-p1@d1 {
+				reg = <0xd1 0x1>;
+				bits = <1 6>;
+			};
+
+			tsens_s1_p1: s1-p1@d1 {
+				reg = <0xd1 0x2>;
+				bits = <7 6>;
+			};
+
+			tsens_s1_p2: s1-p2@d2 {
+				reg = <0xd2 0x2>;
+				bits = <5 6>;
+			};
+
+			tsens_s2_p1: s2-p1@d3 {
+				reg = <0xd3 0x2>;
+				bits = <3 6>;
+			};
+
+			tsens_s2_p2: s2-p2@d4 {
+				reg = <0xd4 0x1>;
+				bits = <1 6>;
+			};
+
+			tsens_s3_p1: s3-p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <7 6>;
+			};
+
+			tsens_s3_p2: s3-p2@d5 {
+				reg = <0xd5 0x2>;
+				bits = <5 6>;
+			};
+
+			tsens_s4_p1: s4-p1@d6 {
+				reg = <0xd6 0x2>;
+				bits = <3 6>;
+			};
+
+			tsens_s4_p2: s4-p2@d7 {
+				reg = <0xd7 0x1>;
+				bits = <1 6>;
+			};
+		};
+
+		rpm_msg_ram: sram@60000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0x00060000 0x8000>;
+		};
+
+		bimc: interconnect@400000 {
+			compatible = "qcom,msm8939-bimc";
+			reg = <0x00400000 0x62000>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+				 <&rpmcc RPM_SMD_BIMC_A_CLK>;
+			#interconnect-cells = <1>;
+		};
+
+		tsens: thermal-sensor@4a9000 {
+			compatible = "qcom,msm8939-tsens", "qcom,tsens-v0_1";
+			reg = <0x004a9000 0x1000>, /* TM */
+			      <0x004a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2";
+			#qcom,sensors = <9>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0x004ab000 0x4>;
+		};
+
+		pcnoc: interconnect@500000 {
+			compatible = "qcom,msm8939-pcnoc";
+			reg = <0x00500000 0x11000>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_PCNOC_CLK>,
+				 <&rpmcc RPM_SMD_PCNOC_A_CLK>;
+			#interconnect-cells = <1>;
+		};
+
+		snoc: interconnect@580000 {
+			compatible = "qcom,msm8939-snoc";
+			reg = <0x00580000 0x14080>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+				 <&rpmcc RPM_SMD_SNOC_A_CLK>;
+			#interconnect-cells = <1>;
+
+			snoc_mm: interconnect-snoc {
+				compatible = "qcom,msm8939-snoc-mm";
+				clock-names = "bus", "bus_a";
+				clocks = <&rpmcc RPM_SMD_SYSMMNOC_CLK>,
+					 <&rpmcc RPM_SMD_SYSMMNOC_A_CLK>;
+				#interconnect-cells = <1>;
+			};
+		};
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,msm8916-pinctrl";
+			reg = <0x01000000 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 122>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			blsp1_uart1_default: blsp1-uart1-default-state {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3";
+				function = "blsp_uart1";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			blsp1_uart2_default: blsp1-uart2-default-state {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			blsp1_uart2_sleep: blsp1-uart2-sleep-state {
+				pins = "gpio4", "gpio5";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			camera_front_default: camera-front-default-state {
+				pwdn-pins {
+					pins = "gpio33";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				rst-pins {
+					pins = "gpio28";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				mclk1-pins {
+					pins = "gpio27";
+					function = "cam_mclk1";
+					drive-strength = <16>;
+					bias-disable;
+				};
+			};
+
+			camera_rear_default: camera-rear-default-state {
+				pwdn-pins {
+					pins = "gpio34";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				rst-pins {
+					pins = "gpio35";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				mclk0-pins {
+					pins = "gpio26";
+					function = "cam_mclk0";
+					drive-strength = <16>;
+					bias-disable;
+				};
+			};
+
+			cci0_default: cci0-default-state {
+				pins = "gpio29", "gpio30";
+				function = "cci_i2c";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			cdc_pdm_lines_default: pdm-lines-default-state {
+				pins = "gpio63", "gpio64", "gpio65", "gpio66",
+				       "gpio67", "gpio68";
+				function = "cdc_pdm0";
+				drive-strength = <8>;
+				bias-disable;
+			};
+
+			cdc_pdm_lines_sleep: pdm-lines-suspend-state {
+				pins = "gpio63", "gpio64", "gpio65", "gpio66",
+				       "gpio67", "gpio68";
+				function = "cdc_pdm0";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			cdc_dmic_lines_act: cdc-dmic-lines-on-state {
+				clk-pins {
+					pins = "gpio0";
+					function = "dmic0_clk";
+					drive-strength = <8>;
+				};
+
+				data-pins {
+					pins = "gpio1";
+					function = "dmic0_data";
+					drive-strength = <8>;
+				};
+			};
+
+			cdc_dmic_lines_sus: cdc-dmic-lines-off-state {
+				clk-pins {
+					pins = "gpio0";
+					function = "dmic0_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				data-pins {
+					pins = "gpio1";
+					function = "dmic0_data";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			ext-mclk-tlmm-lines-state {
+				ext_mclk_tlmm_lines_act: mclk-lines-on-pins {
+					pins = "gpio116";
+					function = "pri_mi2s";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				ext_mclk_tlmm_lines_sus: mclk-lines-off-pins {
+					pins = "gpio116";
+					function = "pri_mi2s";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			ext-pri-tlmm-lines-state {
+				ext_pri_tlmm_lines_act: ext-pa-on-pins {
+					pins = "gpio113", "gpio114", "gpio115", "gpio116";
+					function = "pri_mi2s";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				ext_pri_tlmm_lines_sus: ext-pa-off-pins {
+					pins = "gpio113", "gpio114", "gpio115", "gpio116";
+					function = "pri_mi2s";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			ext-pri-ws-line-state {
+				ext_pri_ws_act: ext-pa-on-pins {
+					pins = "gpio110";
+					function = "pri_mi2s_ws";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				ext_pri_ws_sus: ext-pa-off-pins {
+					pins = "gpio110";
+					function = "pri_mi2s_ws";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			/* secondary Mi2S */
+			ext-sec-tlmm-lines-state {
+				ext_sec_tlmm_lines_act: tlmm-lines-on-pins {
+					pins = "gpio112", "gpio117", "gpio118", "gpio119";
+					function = "sec_mi2s";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				ext_sec_tlmm_lines_sus: tlmm-lines-off-pins {
+					pins = "gpio112", "gpio117", "gpio118", "gpio119";
+					function = "sec_mi2s";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			i2c1_default: i2c1-default-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c1_sleep: i2c1-sleep-state {
+				pins = "gpio2", "gpio3";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c2_default: i2c2-default-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c2_sleep: i2c2-sleep-state {
+				pins = "gpio6", "gpio7";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c3_default: i2c3-default-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c3_sleep: i2c3-sleep-state {
+				pins = "gpio10", "gpio11";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c4_default: i2c4-default-state {
+				pins = "gpio14", "gpio15";
+				function = "blsp_i2c4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c4_sleep: i2c4-sleep-state {
+				pins = "gpio14", "gpio15";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c5_default: i2c5-default-state {
+				pins = "gpio18", "gpio19";
+				function = "blsp_i2c5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c5_sleep: i2c5-sleep-state {
+				pins = "gpio18", "gpio19";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c6_default: i2c6-default-state {
+				pins = "gpio22", "gpio23";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c6_sleep: i2c6-sleep-state {
+				pins = "gpio22", "gpio23";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdc1_default_state: sdc1-default-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <16>;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+			};
+
+			sdc1_sleep_state: sdc1-sleep-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+			};
+
+			sdc2_default_state: sdc2-default-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <16>;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <10>;
+				};
+
+				cd-pins {
+					pins = "gpio38";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			sdc2_sleep_state: sdc2-sleep-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				cd-pins {
+					pins = "gpio38";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			spi1_default: spi1-default-state {
+				spi-pins {
+					pins = "gpio0", "gpio1", "gpio3";
+					function = "blsp_spi1";
+					drive-strength = <12>;
+					bias-disable;
+				};
+
+				cs-pins {
+					pins = "gpio2";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+					output-high;
+				};
+			};
+
+			spi1_sleep: spi1-sleep-state {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			spi2_default: spi2-default-state {
+				spi-pins {
+					pins = "gpio4", "gpio5", "gpio7";
+					function = "blsp_spi2";
+					drive-strength = <12>;
+					bias-disable;
+				};
+
+				cs-pins {
+					pins = "gpio6";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+					output-high;
+				};
+			};
+
+			spi2_sleep: spi2-sleep-state {
+				pins = "gpio4", "gpio5", "gpio6", "gpio7";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			spi3_default: spi3-default-state {
+				spi-pins {
+					pins = "gpio8", "gpio9", "gpio11";
+					function = "blsp_spi3";
+					drive-strength = <12>;
+					bias-disable;
+				};
+
+				cs-pins {
+					pins = "gpio10";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+					output-high;
+				};
+			};
+
+			spi3_sleep: spi3-sleep-state {
+				pins = "gpio8", "gpio9", "gpio10", "gpio11";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			spi4_default: spi4-default-state {
+				spi-pins {
+					pins = "gpio12", "gpio13", "gpio15";
+					function = "blsp_spi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+
+				cs-pins {
+					pins = "gpio14";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+					output-high;
+				};
+			};
+
+			spi4_sleep: spi4-sleep-state {
+				pins = "gpio12", "gpio13", "gpio14", "gpio15";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			spi5_default: spi5-default-state {
+				spi-pins {
+					pins = "gpio16", "gpio17", "gpio19";
+					function = "blsp_spi5";
+					drive-strength = <12>;
+					bias-disable;
+				};
+
+				cs-pins {
+					pins = "gpio18";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+					output-high;
+				};
+			};
+
+			spi5_sleep: spi5-sleep-state {
+				pins = "gpio16", "gpio17", "gpio18", "gpio19";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			spi6_default: spi6-default-state {
+				spi-pins {
+					pins = "gpio20", "gpio21", "gpio23";
+					function = "blsp_spi6";
+					drive-strength = <12>;
+					bias-disable;
+				};
+
+				cs-pins {
+					pins = "gpio22";
+					function = "gpio";
+					drive-strength = <16>;
+					bias-disable;
+					output-high;
+				};
+			};
+
+			spi6_sleep: spi6-sleep-state {
+				pins = "gpio20", "gpio21", "gpio22", "gpio23";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			wcnss_pin_a: wcnss-active-state {
+				pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "wcss_wlan";
+				drive-strength = <6>;
+				bias-pull-up;
+			};
+		};
+
+		gcc: clock-controller@1800000 {
+			compatible = "qcom,gcc-msm8939";
+			reg = <0x01800000 0x80000>;
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&sleep_clk>,
+				 <&dsi_phy0 1>,
+				 <&dsi_phy0 0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "sleep_clk",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "ext_mclk",
+				      "ext_pri_i2s",
+				      "ext_sec_i2s";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01905000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1937000 {
+			compatible = "qcom,tcsr-msm8916", "syscon";
+			reg = <0x01937000 0x30000>;
+		};
+
+		mdss: display-subsystem@1a00000 {
+			compatible = "qcom,mdss";
+			reg = <0x01a00000 0x1000>,
+			      <0x01ac8000 0x3000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "vsync";
+
+			power-domains = <&gcc MDSS_GDSC>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#interrupt-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			mdp: display-controller@1a01000 {
+				compatible = "qcom,mdp5";
+				reg = <0x01a01000 0x89000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				iommus = <&apps_iommu 4>;
+
+				interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
+						<&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>;
+				interconnect-names = "mdp0-mem", "mdp1-mem";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdp5_intf2_out: endpoint {
+							remote-endpoint = <&dsi1_in>;
+						};
+					};
+				};
+			};
+
+			dsi0: dsi@1a98000 {
+				compatible = "qcom,msm8916-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0x01a98000 0x25c>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_BYTE0_CLK>,
+					 <&gcc GCC_MDSS_PCLK0_CLK>,
+					 <&gcc GCC_MDSS_ESC0_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core";
+				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+						  <&gcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi_phy0 0>,
+							 <&dsi_phy0 1>;
+
+				phys = <&dsi_phy0>;
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi_phy0: phy@1a98300 {
+				compatible = "qcom,dsi-phy-28nm-lp";
+				reg = <0x01a98300 0xd4>,
+				      <0x01a98500 0x280>,
+				      <0x01a98780 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+				clock-names = "iface", "ref";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			dsi1: dsi@1aa0000 {
+				compatible = "qcom,msm8916-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0x01aa0000 0x25c>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5>;
+
+				clocks = <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_BYTE1_CLK>,
+					 <&gcc GCC_MDSS_PCLK1_CLK>,
+					 <&gcc GCC_MDSS_ESC1_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core";
+				assigned-clocks = <&gcc BYTE1_CLK_SRC>,
+						  <&gcc PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&dsi_phy0 0>,
+							 <&dsi_phy0 1>;
+				phys = <&dsi_phy1>;
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+							remote-endpoint = <&mdp5_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi_phy1: phy@1aa0300 {
+				compatible = "qcom,dsi-phy-28nm-lp";
+				reg = <0x01aa0300 0xd4>,
+				      <0x01aa0500 0x280>,
+				      <0x01aa0780 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+				clock-names = "iface", "ref";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gpu@1c00000 {
+			compatible = "qcom,adreno-405.0", "qcom,adreno";
+			reg = <0x01c00000 0x10000>;
+			reg-names = "kgsl_3d0_reg_memory";
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+			clock-names = "core",
+				      "iface",
+				      "mem",
+				      "mem_iface",
+				      "alt_mem_iface",
+				      "gfx3d",
+				      "rbbmtimer";
+			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
+				 <&gcc GCC_OXILI_AHB_CLK>,
+				 <&gcc GCC_OXILI_GMEM_CLK>,
+				 <&gcc GCC_BIMC_GFX_CLK>,
+				 <&gcc GCC_BIMC_GPU_CLK>,
+				 <&gcc GFX3D_CLK_SRC>,
+				 <&gcc GCC_OXILI_TIMER_CLK>;
+			power-domains = <&gcc OXILI_GDSC>;
+			operating-points-v2 = <&opp_table>;
+			iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
+
+			opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-550000000 {
+					opp-hz = /bits/ 64 <550000000>;
+				};
+
+				opp-465000000 {
+					opp-hz = /bits/ 64 <465000000>;
+				};
+
+				opp-400000000 {
+					opp-hz = /bits/ 64 <400000000>;
+				};
+
+				opp-220000000 {
+					opp-hz = /bits/ 64 <220000000>;
+				};
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+				};
+			};
+		};
+
+		apps_iommu: iommu@1ef0000 {
+			compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
+			reg = <0x01ef0000 0x3000>;
+			ranges = <0 0x01e20000 0x40000>;
+			clocks = <&gcc GCC_SMMU_CFG_CLK>,
+				 <&gcc GCC_APSS_TCU_CLK>;
+			clock-names = "iface", "bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#iommu-cells = <1>;
+			qcom,iommu-secure-id = <17>;
+
+			/* mdp_0: */
+			iommu-ctx@4000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x4000 0x1000>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			/* venus_ns: */
+			iommu-ctx@5000 {
+				compatible = "qcom,msm-iommu-v1-sec";
+				reg = <0x5000 0x1000>;
+				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		gpu_iommu: iommu@1f08000 {
+			compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
+			ranges = <0 0x1f08000 0x10000>;
+			clocks = <&gcc GCC_SMMU_CFG_CLK>,
+				 <&gcc GCC_GFX_TCU_CLK>,
+				 <&gcc GCC_GFX_TBU_CLK>;
+			clock-names = "iface", "bus", "tbu";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#iommu-cells = <1>;
+			qcom,iommu-secure-id = <18>;
+
+			/* gfx3d_user: */
+			iommu-ctx@1000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x1000 0x1000>;
+				interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			/* gfx3d_priv: */
+			iommu-ctx@2000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x2000 0x1000>;
+				interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		spmi_bus: spmi@200f000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0200f000 0x001000>,
+			      <0x02400000 0x400000>,
+			      <0x02c00000 0x400000>,
+			      <0x03800000 0x200000>,
+			      <0x0200a000 0x002100>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		mpss: remoteproc@4080000 {
+			compatible = "qcom,msm8916-mss-pil";
+			reg = <0x04080000 0x100>, <0x04020000 0x040>;
+			reg-names = "qdsp6", "rmb";
+			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+					      <&hexagon_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&hexagon_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&hexagon_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&hexagon_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface",
+				      "bus",
+				      "mem",
+				      "xo";
+			power-domains = <&rpmpd MSM8939_VDDMDCX>,
+					<&rpmpd MSM8939_VDDMX>;
+			power-domain-names = "cx", "mx";
+			qcom,smem-states = <&hexagon_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+			resets = <&scm 0>;
+			reset-names = "mss_restart";
+			qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>;
+			status = "disabled";
+
+			mba {
+				memory-region = <&mba_mem>;
+			};
+
+			mpss {
+				memory-region = <&mpss_mem>;
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,smd-edge = <0>;
+				mboxes = <&apcs1_mbox 12>;
+				qcom,remote-pid = <1>;
+
+				label = "hexagon";
+			};
+		};
+
+		sound: sound@7702000 {
+			compatible = "qcom,apq8016-sbc-sndcard";
+			reg = <0x07702000 0x4>,
+			      <0x07702004 0x4>;
+			reg-names = "mic-iomux", "spkr-iomux";
+			status = "disabled";
+		};
+
+		lpass: audio-controller@7708000 {
+			compatible = "qcom,apq8016-lpass-cpu";
+			reg = <0x07708000 0x10000>;
+			reg-names = "lpass-lpaif";
+			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "lpass-irq-lpaif";
+			clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
+				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
+				 <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
+				 <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>,
+				 <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
+				 <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>;
+			clock-names = "ahbix-clk",
+				      "mi2s-bit-clk0",
+				      "mi2s-bit-clk1",
+				      "mi2s-bit-clk2",
+				      "mi2s-bit-clk3",
+				      "pcnoc-mport-clk",
+				      "pcnoc-sway-clk";
+			#sound-dai-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		lpass_codec: audio-codec@771c000 {
+			compatible = "qcom,msm8916-wcd-digital-codec";
+			reg = <0x0771c000 0x400>;
+			clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+				 <&gcc GCC_CODEC_DIGCODEC_CLK>;
+			clock-names = "ahbix-clk", "mclk";
+			#sound-dai-cells = <1>;
+		};
+
+		sdhc_1: mmc@7824900 {
+			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0x07824900 0x11c>, <0x07824000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			resets = <&gcc GCC_SDCC1_BCR>;
+			mmc-ddr-1_8v;
+			bus-width = <8>;
+			non-removable;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@7864900 {
+			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0x07864900 0x11c>, <0x07864000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names =  "iface", "core", "xo";
+			resets = <&gcc GCC_SDCC2_BCR>;
+			bus-width = <4>;
+			status = "disabled";
+		};
+
+		blsp_dma: dma-controller@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x23000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		blsp1_uart1: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&blsp1_uart1_default>;
+			pinctrl-1 = <&blsp1_uart1_sleep>;
+			pinctrl-names = "default", "sleep";
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b0000 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
+			pinctrl-names = "default", "sleep";
+			status = "disabled";
+		};
+
+		blsp_i2c1: i2c@78b5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b5000 0x500>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c1_default>;
+			pinctrl-1 = <&i2c1_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi1: spi@78b5000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b5000 0x500>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi1_default>;
+			pinctrl-1 = <&spi1_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c2: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b6000 0x500>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names =  "core", "iface";
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c2_default>;
+			pinctrl-1 = <&i2c2_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi2: spi@78b6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b6000 0x500>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi2_default>;
+			pinctrl-1 = <&spi2_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c3: i2c@78b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b7000 0x500>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names =  "core", "iface";
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c3_default>;
+			pinctrl-1 = <&i2c3_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi3: spi@78b7000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b7000 0x500>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi3_default>;
+			pinctrl-1 = <&spi3_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c4: i2c@78b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b8000 0x500>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names =  "core", "iface";
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c4_default>;
+			pinctrl-1 = <&i2c4_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi4: spi@78b8000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b8000 0x500>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi4_default>;
+			pinctrl-1 = <&spi4_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c5: i2c@78b9000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b9000 0x500>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names =  "core", "iface";
+			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c5_default>;
+			pinctrl-1 = <&i2c5_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi5: spi@78b9000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b9000 0x500>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi5_default>;
+			pinctrl-1 = <&spi5_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c6: i2c@78ba000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078ba000 0x500>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names =  "core", "iface";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c6_default>;
+			pinctrl-1 = <&i2c6_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi6: spi@78ba000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078ba000 0x500>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi6_default>;
+			pinctrl-1 = <&spi6_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		usb: usb@78d9000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x078d9000 0x200>,
+			      <0x078d9200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <80000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			#reset-cells = <1>;
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			adp-disable;
+			hnp-disable;
+			srp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+
+			ulpi {
+				usb_hs_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8916",
+						     "qcom,usb-hs-phy";
+					clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+						 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					#phy-cells = <0>;
+					qcom,init-seq = /bits/ 8 <0x0 0x44>,
+								 <0x1 0x6b>,
+								 <0x2 0x24>,
+								 <0x3 0x13>;
+				};
+			};
+		};
+
+		pronto: remoteproc@a204000 {
+			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+			reg = <0x0a204000 0x2000>,
+			      <0x0a202000 0x1000>,
+			      <0x0a21b000 0x3000>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			memory-region = <&wcnss_mem>;
+
+			power-domains = <&rpmpd MSM8939_VDDCX>,
+					<&rpmpd MSM8939_VDDMX>;
+			power-domain-names = "cx", "mx";
+
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&wcnss_pin_a>;
+
+			status = "disabled";
+
+			iris {
+				compatible = "qcom,wcn3620";
+				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+				clock-names = "xo";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 142 1>;
+				qcom,ipc = <&apcs1_mbox 8 17>;
+				qcom,smd-edge = <6>;
+				qcom,remote-pid = <4>;
+
+				label = "pronto";
+
+				wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+
+					qcom,mmio = <&pronto>;
+
+					bluetooth {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>,
+								   <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable",
+									"tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>,
+			      <0x0b001000 0x1000>, <0x0b004000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		apcs1_mbox: mailbox@b011000 {
+			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+			reg = <0x0b011000 0x1000>;
+			clocks = <&a53pll_c1>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "pll", "aux", "ref";
+			#clock-cells = <0>;
+			assigned-clocks = <&apcs2>;
+			assigned-clock-rates = <297600000>;
+			#mbox-cells = <1>;
+		};
+
+		a53pll_c1: clock@b016000 {
+			compatible = "qcom,msm8939-a53pll";
+			reg = <0x0b016000 0x40>;
+			#clock-cells = <0>;
+		};
+
+		acc0: clock-controller@b088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b088000 0x1000>;
+		};
+
+		saw0: power-manager@b089000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b089000 0x1000>;
+		};
+
+		acc1: clock-controller@b098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b098000 0x1000>;
+		};
+
+		saw1: power-manager@b099000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b099000 0x1000>;
+		};
+
+		acc2: clock-controller@b0a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b0a8000 0x1000>;
+		};
+
+		saw2: power-manager@b0a9000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b0a9000 0x1000>;
+		};
+
+		acc3: clock-controller@b0b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b0b8000 0x1000>;
+		};
+
+		saw3: power-manager@b0b9000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b0b9000 0x1000>;
+		};
+
+		apcs0_mbox: mailbox@b111000 {
+			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+			reg = <0x0b111000 0x1000>;
+			clocks = <&a53pll_c0>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "pll", "aux", "ref";
+			#clock-cells = <0>;
+			#mbox-cells = <1>;
+		};
+
+		a53pll_c0: clock@b116000 {
+			compatible = "qcom,msm8939-a53pll";
+			reg = <0x0b116000 0x40>;
+			#clock-cells = <0>;
+		};
+
+		timer@b120000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0b120000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			frame@b121000 {
+				reg = <0x0b121000 0x1000>,
+				      <0x0b122000 0x1000>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <0>;
+			};
+
+			frame@b123000 {
+				reg = <0x0b123000 0x1000>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <1>;
+				status = "disabled";
+			};
+
+			frame@b124000 {
+				reg = <0x0b124000 0x1000>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <2>;
+				status = "disabled";
+			};
+
+			frame@b125000 {
+				reg = <0x0b125000 0x1000>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <3>;
+				status = "disabled";
+			};
+
+			frame@b126000 {
+				reg = <0x0b126000 0x1000>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <4>;
+				status = "disabled";
+			};
+
+			frame@b127000 {
+				reg = <0x0b127000 0x1000>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <5>;
+				status = "disabled";
+			};
+
+			frame@b128000 {
+				reg = <0x0b128000 0x1000>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <6>;
+				status = "disabled";
+			};
+		};
+
+		acc4: clock-controller@b188000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b188000 0x1000>;
+		};
+
+		saw4: power-manager@b189000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b189000 0x1000>;
+		};
+
+		acc5: clock-controller@b198000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b198000 0x1000>;
+		};
+
+		saw5: power-manager@b199000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b199000 0x1000>;
+		};
+
+		acc6: clock-controller@b1a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b1a8000 0x1000>;
+		};
+
+		saw6: power-manager@b1a9000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b1a9000 0x1000>;
+		};
+
+		acc7: clock-controller@b1b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b1b8000 0x1000>;
+		};
+
+		saw7: power-manager@b1b9000 {
+			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b1b9000 0x1000>;
+		};
+
+		a53pll_cci: clock@b1d0000 {
+			compatible = "qcom,msm8939-a53pll";
+			reg = <0x0b1d0000 0x40>;
+			#clock-cells = <0>;
+		};
+
+		apcs2: mailbox@b1d1000 {
+			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+			reg = <0x0b1d1000 0x1000>;
+			clocks = <&a53pll_cci>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "pll", "aux", "ref";
+			#clock-cells = <0>;
+			#mbox-cells = <1>;
+		};
+	};
+
+	thermal_zones: thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu0_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu0_crit: trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu1_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu1_crit: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu1_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu2_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu2_crit: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu2_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu3_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu3_crit: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu3_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu4567-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu4567_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu4567_crit: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu4567_alert>;
+					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				gpu_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				gpu_crit: gpu_crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		modem1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				modem1_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		modem2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				modem2_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		camera-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				cam_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};