@@ -946,6 +946,8 @@ config MSM_SERIAL
config MSM_GENI_SERIAL
bool "Qualcomm on-chip GENI UART"
+ select MISC
+ imply QCOM_GENI_SE
help
Support UART based on Generic Interface (GENI) Serial Engine (SE),
used on Qualcomm Snapdragon SoCs. Should support all qualcomm SOCs
@@ -13,6 +13,7 @@
#include <dm.h>
#include <errno.h>
#include <linux/delay.h>
+#include <misc.h>
#include <serial.h>
#define UART_OVERSAMPLING 32
@@ -110,6 +111,10 @@
#define TX_FIFO_DEPTH_MSK (GENMASK(21, 16))
#define TX_FIFO_DEPTH_SHFT 16
+/* GENI SE QUP Registers */
+#define QUP_HW_VER_REG 0x4
+#define QUP_SE_VERSION_2_5 0x20050000
+
/*
* Predefined packing configuration of the serial engine (CFG0, CFG1 regs)
* for uart mode.
@@ -127,6 +132,7 @@ DECLARE_GLOBAL_DATA_PTR;
struct msm_serial_data {
phys_addr_t base;
u32 baud;
+ u32 oversampling;
};
unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200,
@@ -246,7 +252,7 @@ static int msm_serial_setbrg(struct udevice *dev, int baud)
priv->baud = baud;
- clk_rate = get_clk_div_rate(baud, UART_OVERSAMPLING, &clk_div);
+ clk_rate = get_clk_div_rate(baud, priv->oversampling, &clk_div);
geni_serial_set_clock_rate(dev, clk_rate);
geni_serial_baud(priv->base, clk_div, baud);
@@ -480,6 +486,28 @@ static const struct dm_serial_ops msm_serial_ops = {
.setbrg = msm_serial_setbrg,
};
+static void geni_set_oversampling(struct udevice *dev)
+{
+ struct msm_serial_data *priv = dev_get_priv(dev);
+ struct udevice *parent_dev = dev_get_parent(dev);
+ u32 geni_se_version;
+ int ret;
+
+ priv->oversampling = UART_OVERSAMPLING;
+
+ /*
+ * It could happen that GENI SE IP is missing in the board's device
+ * tree or GENI UART node is a direct child of SoC device tree node.
+ */
+ if (device_get_uclass_id(parent_dev) != UCLASS_MISC)
+ return;
+
+ ret = misc_read(parent_dev, QUP_HW_VER_REG,
+ &geni_se_version, sizeof(geni_se_version));
+ if (!ret && geni_se_version >= QUP_SE_VERSION_2_5)
+ priv->oversampling /= 2;
+}
+
static inline void geni_serial_init(struct udevice *dev)
{
struct msm_serial_data *priv = dev_get_priv(dev);
@@ -523,6 +551,8 @@ static int msm_serial_probe(struct udevice *dev)
{
struct msm_serial_data *priv = dev_get_priv(dev);
+ geni_set_oversampling(dev);
+
/* No need to reinitialize the UART after relocation */
if (gd->flags & GD_FLG_RELOC)
return 0;
Starting from QUP v2.5 the value of oversampling is changed from 32 to 16, keeping the old value on newer platforms results on wrong set UART IP clock divider, thus the asked baudrate does not correspond to the actually set with all the consequencies for a user. The change links the driver to a new Qualcomm GENI SE QUP driver to get its hardware version and update the oversampling value. Deliberately the code under CONFIG_DEBUG_UART_MSM_GENI is not touched, since a wanted baudrate can be controlled by setting a modified CONFIG_DEBUG_UART_CLOCK build time variable. Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> --- drivers/serial/Kconfig | 2 ++ drivers/serial/serial_msm_geni.c | 32 +++++++++++++++++++++++++++++++- 2 files changed, 33 insertions(+), 1 deletion(-)