new file mode 100644
@@ -0,0 +1,57 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+.. include:: <isonum.txt>
+
+================================
+Starfive Camera Subsystem driver
+================================
+
+Introduction
+------------
+
+This file documents the driver for the Starfive Camera Subsystem found on
+Starfive JH7110 SoC. The driver is located under drivers/media/platform/
+starfive.
+
+The driver implements V4L2, Media controller and v4l2_subdev interfaces.
+Camera sensor using V4L2 subdev interface in the kernel is supported.
+
+The driver has been successfully used on the Gstreamer 1.18.5 with
+v4l2src plugin.
+
+
+Starfive Camera Subsystem hardware
+----------------------------------
+
+The Starfive Camera Subsystem hardware consists of:
+
+- MIPI DPHY Receiver: receives mipi data from a MIPI camera sensor.
+- MIPI CSIRx Controller: is responsible for handling and decoding CSI2 protocol
+ based camera sensor data stream.
+- ISP: handles the image data streams from the MIPI CSIRx Controller.
+- VIN(Video In): a top-level module, is responsible for controlling power
+ and clocks to other modules, dumps the input data to memory or transfers the
+ input data to ISP.
+
+
+Topology
+--------
+
+The media controller pipeline graph is as follows:
+
+.. _starfive_camss_graph:
+
+.. kernel-figure:: starfive_camss_graph.dot
+ :alt: starfive_camss_graph.dot
+ :align: center
+
+The driver has 2 video devices:
+
+- stf_vin0_wr_video0: capture device for images directly from the VIN module.
+- stf_vin0_isp0_video1: capture device for images without scaling.
+
+The driver has 3 subdevices:
+
+- stf_isp0: is responsible for all the isp operations.
+- stf_vin0_wr: used to dump RAW images to memory.
+- stf_vin0_isp0: used to capture images for the stf_vin0_isp0_video1 device.
new file mode 100644
@@ -0,0 +1,16 @@
+digraph board {
+ rankdir=TB
+ n00000001 [label="{{<port0> 0} | stf_isp0\n/dev/v4l-subdev0 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green]
+ n00000001:port1 -> n0000000d:port0
+ n00000004 [label="{{<port0> 0} | stf_vin0_wr\n/dev/v4l-subdev1 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green]
+ n00000004:port1 -> n00000007 [style=bold]
+ n00000007 [label="stf_vin0_wr_video0\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
+ n0000000d [label="{{<port0> 0} | stf_vin0_isp0\n/dev/v4l-subdev2 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green]
+ n0000000d:port1 -> n00000010 [style=bold]
+ n00000010 [label="stf_vin0_isp0_video1\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
+ n00000018 [label="{{<port0> 0} | cdns_csi2rx.19800000.csi-bridge\n | {<port1> 1 | <port2> 2 | <port3> 3 | <port4> 4}}", shape=Mrecord, style=filled, fillcolor=green]
+ n00000018:port1 -> n00000004:port0 [style=dashed]
+ n00000018:port1 -> n00000001:port0
+ n00000028 [label="{{} | imx219 6-0010\n | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green]
+ n00000028:port0 -> n00000018:port0 [style=bold]
+}
@@ -27,6 +27,7 @@ Video4Linux (V4L) driver-specific documentation
si470x
si4713
si476x
+ starfive_camss
vimc
visl
vivid
@@ -19914,6 +19914,7 @@ M: Jack Zhu <jack.zhu@starfivetech.com>
M: Changhuang Liang <changhuang.liang@starfivetech.com>
L: linux-media@vger.kernel.org
S: Maintained
+F: Documentation/admin-guide/media/starfive_camss.rst
F: Documentation/devicetree/bindings/media/starfive,jh7110-camss.yaml
STARFIVE DEVICETREES
Add starfive_camss.rst file that documents the Starfive Camera Subsystem driver which is used for handing image sensor data. Signed-off-by: Jack Zhu <jack.zhu@starfivetech.com> --- .../admin-guide/media/starfive_camss.rst | 57 +++++++++++++++++++ .../media/starfive_camss_graph.dot | 16 ++++++ .../admin-guide/media/v4l-drivers.rst | 1 + MAINTAINERS | 1 + 4 files changed, 75 insertions(+) create mode 100644 Documentation/admin-guide/media/starfive_camss.rst create mode 100644 Documentation/admin-guide/media/starfive_camss_graph.dot