diff mbox series

[5/5] arm64: dts: ti: k3-j7200: Add bootph-pre-ram for u-boot

Message ID 20230426103219.1565266-6-u-kumar1@ti.com
State New
Headers show
Series [1/5] arm64: dts: ti: k3-j7200: Add general purpose timers | expand

Commit Message

Kumar, Udit April 26, 2023, 10:32 a.m. UTC 
Adding bootph-pre-ram property for pin mux needed by
uboot.

Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 5 +++++
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi           | 3 +++
 2 files changed, 8 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 2cdfd957dd12..1bcb94aec588 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -81,7 +81,9 @@  vdd_sd_dv: gpio-regulator-TLV71033 {
 };
 
 &wkup_pmx0 {
+	bootph-pre-ram;
 	mcu_uart0_pins_default: mcu_uart0_pins_default {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
 			J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
@@ -91,6 +93,7 @@  J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
 	};
 
 	wkup_uart0_pins_default: wkup_uart0_pins_default {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
 			J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
@@ -125,7 +128,9 @@  J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 };
 
 &main_pmx0 {
+	bootph-pre-ram;
 	main_uart0_pins_default: main_uart0_pins_default {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
 			J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 269424154771..d2500837a0e8 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -119,7 +119,9 @@  J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
 };
 
 &wkup_pmx2 {
+	bootph-pre-ram;
 	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+			bootph-pre-ram;
 			pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
 			J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
@@ -129,6 +131,7 @@  J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
 
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
 			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */