@@ -1104,6 +1104,30 @@ dsim_from_lcdif: endpoint {
};
};
+ isi: isi@32e20000 {
+ compatible = "fsl,imx8mn-isi";
+ reg = <0x32e20000 0x8000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MN_CLK_DISP_AXI_ROOT>,
+ <&clk IMX8MN_CLK_DISP_APB_ROOT>;
+ clock-names = "axi", "apb";
+ fsl,blk-ctrl = <&disp_blk_ctrl>;
+ power-domains = <&disp_blk_ctrl IMX8MN_DISPBLK_PD_ISI>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ isi_in: endpoint {
+ remote-endpoint = <&mipi_csi_out>;
+ };
+ };
+ };
+ };
+
disp_blk_ctrl: blk-ctrl@32e28000 {
compatible = "fsl,imx8mn-disp-blk-ctrl", "syscon";
reg = <0x32e28000 0x100>;
@@ -1147,6 +1171,42 @@ disp_blk_ctrl: blk-ctrl@32e28000 {
#power-domain-cells = <1>;
};
+ mipi_csi: mipi-csi@32e30000 {
+ compatible = "fsl,imx8mm-mipi-csi2";
+ reg = <0x32e30000 0x1000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ assigned-clocks = <&clk IMX8MN_CLK_CAMERA_PIXEL>,
+ <&clk IMX8MN_CLK_CSI1_PHY_REF>;
+ assigned-clock-parents = <&clk IMX8MN_SYS_PLL2_1000M>,
+ <&clk IMX8MN_SYS_PLL2_1000M>;
+ assigned-clock-rates = <333000000>;
+ clock-frequency = <333000000>;
+ clocks = <&clk IMX8MN_CLK_DISP_APB_ROOT>,
+ <&clk IMX8MN_CLK_CAMERA_PIXEL>,
+ <&clk IMX8MN_CLK_CSI1_PHY_REF>,
+ <&clk IMX8MN_CLK_DISP_AXI_ROOT>;
+ clock-names = "pclk", "wrap", "phy", "axi";
+ power-domains = <&disp_blk_ctrl IMX8MN_DISPBLK_PD_MIPI_CSI>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mipi_csi_out: endpoint {
+ remote-endpoint = <&isi_in>;
+ };
+ };
+ };
+ };
+
usbotg1: usb@32e40000 {
compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x32e40000 0x200>;
The CSI in the imx8mn is the same as what is used in the imx8mm, but it's routed to the ISI on the Nano. Add both the ISI and CSI nodes, and pointing them to each other. Since the CSI capture is dependent on an attached camera, mark both ISI and CSI as disabled by default. Signed-off-by: Adam Ford <aford173@gmail.com> --- V2: Change from a singular 'port' to 'ports' per feedback from Laurent Pinchart "When a single port is present using a "port" node directly is fine from an OF graph point of view, but to avoid too much complexity in the ISI binding the consensus was to always require a "ports" node for the ISI." This is also consistent with the binding YAML file. Change the size allocated to the ISI to 32k. The datasheet indicates it should be 64K, but the disp_blk_ctrl sits at 32e28000. Change the subject from 'Enable' to 'Add' since the ISI and CSI nodes are both technically disabled.