| Message ID | 20230524230459.120681-4-guptarud@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | [1/5] ARM: Add label to sleep_clk in qcom-msm8960.dtsi | expand |
On 25.05.2023 01:04, Rudraksha Gupta wrote: > apq8064 and msm8960 are extremely similar SoCs. Therefore copying this > from the apq8064 dtsi file should not be a problem. Tested this on the > Samsung Galaxy Express and this works. > > Signed-off-by: Rudraksha Gupta <guptarud@gmail.com> > --- Well admitting to this upfront doesn't sound very good :P Please reword the message to something like: ARM: dts: qcom-msm8960: Add USB Add the required nodes to support USB on MSM8960. As it's very similar to APQ8064, the setup is almost identical As for the contents itself, I tried taking a brief peek into the swamp that are the msm-3.0 boardfiles, but I barely managed to escape before getting drawn into the quicksands of 13yo legacy.. I am however inclined to believe that the setup may in fact be identical(or close to) on these two SoCs.. Konrad > arch/arm/boot/dts/qcom-msm8960.dtsi | 33 +++++++++++++++++++++++++++++ > 1 file changed, 33 insertions(+) > > diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi > index a4d8dd2d24a6..b11e606440cd 100644 > --- a/arch/arm/boot/dts/qcom-msm8960.dtsi > +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi > @@ -3,6 +3,7 @@ > > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/qcom,gcc-msm8960.h> > +#include <dt-bindings/reset/qcom,gcc-msm8960.h> > #include <dt-bindings/clock/qcom,lcc-msm8960.h> > #include <dt-bindings/mfd/qcom-rpm.h> > #include <dt-bindings/soc/qcom,gsbi.h> > @@ -370,5 +371,37 @@ gsbi1_spi: spi@16080000 { > status = "disabled"; > }; > }; > + > + usb1: usb@12500000 { > + compatible = "qcom,ci-hdrc"; > + reg = <0x12500000 0x200>, > + <0x12500200 0x200>; > + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>; > + clock-names = "core", "iface"; > + assigned-clocks = <&gcc USB_HS1_XCVR_CLK>; > + assigned-clock-rates = <60000000>; > + resets = <&gcc USB_HS1_RESET>; > + reset-names = "core"; > + phy_type = "ulpi"; > + ahb-burst-config = <0>; > + phys = <&usb_hs1_phy>; > + phy-names = "usb-phy"; > + status = "disabled"; > + #reset-cells = <1>; > + > + ulpi { > + usb_hs1_phy: phy { > + compatible = "qcom,usb-hs-phy-msm8960", > + "qcom,usb-hs-phy"; > + clocks = <&sleep_clk>, <&cxo_board>; > + clock-names = "sleep", "ref"; > + resets = <&usb1 0>; > + reset-names = "por"; > + #phy-cells = <0>; > + }; > + }; > + }; > + > }; > };
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi index a4d8dd2d24a6..b11e606440cd 100644 --- a/arch/arm/boot/dts/qcom-msm8960.dtsi +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi @@ -3,6 +3,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/qcom,gcc-msm8960.h> +#include <dt-bindings/reset/qcom,gcc-msm8960.h> #include <dt-bindings/clock/qcom,lcc-msm8960.h> #include <dt-bindings/mfd/qcom-rpm.h> #include <dt-bindings/soc/qcom,gsbi.h> @@ -370,5 +371,37 @@ gsbi1_spi: spi@16080000 { status = "disabled"; }; }; + + usb1: usb@12500000 { + compatible = "qcom,ci-hdrc"; + reg = <0x12500000 0x200>, + <0x12500200 0x200>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>; + clock-names = "core", "iface"; + assigned-clocks = <&gcc USB_HS1_XCVR_CLK>; + assigned-clock-rates = <60000000>; + resets = <&gcc USB_HS1_RESET>; + reset-names = "core"; + phy_type = "ulpi"; + ahb-burst-config = <0>; + phys = <&usb_hs1_phy>; + phy-names = "usb-phy"; + status = "disabled"; + #reset-cells = <1>; + + ulpi { + usb_hs1_phy: phy { + compatible = "qcom,usb-hs-phy-msm8960", + "qcom,usb-hs-phy"; + clocks = <&sleep_clk>, <&cxo_board>; + clock-names = "sleep", "ref"; + resets = <&usb1 0>; + reset-names = "por"; + #phy-cells = <0>; + }; + }; + }; + }; };
apq8064 and msm8960 are extremely similar SoCs. Therefore copying this from the apq8064 dtsi file should not be a problem. Tested this on the Samsung Galaxy Express and this works. Signed-off-by: Rudraksha Gupta <guptarud@gmail.com> --- arch/arm/boot/dts/qcom-msm8960.dtsi | 33 +++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+)