diff mbox series

[v9,2/2] power: supply: add Qualcomm PMI8998 SMB2 Charger driver

Message ID 20230524-pmi8998-charger-v9-2-cd7f6d03c0ab@linaro.org
State Accepted
Commit 8648aeb5d7b70e13264ff5f444f22081d37d4670
Headers show
Series power: supply: introduce support for the Qualcomm smb2 charger | expand

Commit Message

Caleb Connolly May 26, 2023, 9:44 p.m. UTC
Add a driver for the SMB2 charger block found in the Qualcomm PMI8998
and PM660.

This driver is capable of utilising Qualcomm's Automatic Power Source
Detection (APSD) BC1.2 implementation, as well as Automatic Input
Current Limiting (AICL) to configure the maximum input current
limit of DCP (wall) chargers.

Quick Charge is not currently supported.

Most devices using the smb2 charger have a secondary dedicated charger
chip which is used in parallel to enable faster charger without
overheating. However, not all do, as a result to ensure safety until
these are supported, the maximum current is limited to ~1A via the
FAST_CHARGE_CURRENT_CFG register.

Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
---
 drivers/power/supply/Kconfig                |    9 +
 drivers/power/supply/Makefile               |    1 +
 drivers/power/supply/qcom_pmi8998_charger.c | 1059 +++++++++++++++++++++++++++
 3 files changed, 1069 insertions(+)
diff mbox series

Patch

diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index c78be9f322e6..e1828892332c 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -934,4 +934,13 @@  config BATTERY_UG3105
 	  device is off or suspended, the functionality of this driver is
 	  limited to reporting capacity only.
 
+config CHARGER_QCOM_SMB2
+	tristate "Qualcomm PMI8998 PMIC charger driver"
+	depends on MFD_SPMI_PMIC
+	depends on IIO
+	help
+	  Say Y here to enable the Qualcomm PMIC Charger driver. This
+	  adds support for the SMB2 switch mode battery charger found
+	  in PMI8998 and related PMICs.
+
 endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 4adbfba02d05..d0d6da957943 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -109,3 +109,4 @@  obj-$(CONFIG_BATTERY_ACER_A500)	+= acer_a500_battery.o
 obj-$(CONFIG_BATTERY_SURFACE)	+= surface_battery.o
 obj-$(CONFIG_CHARGER_SURFACE)	+= surface_charger.o
 obj-$(CONFIG_BATTERY_UG3105)	+= ug3105_battery.o
+obj-$(CONFIG_CHARGER_QCOM_SMB2)	+= qcom_pmi8998_charger.o
diff --git a/drivers/power/supply/qcom_pmi8998_charger.c b/drivers/power/supply/qcom_pmi8998_charger.c
new file mode 100644
index 000000000000..d16c5ee17249
--- /dev/null
+++ b/drivers/power/supply/qcom_pmi8998_charger.c
@@ -0,0 +1,1059 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2016-2019 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023, Linaro Ltd.
+ * Author: Caleb Connolly <caleb.connolly@linaro.org>
+ *
+ * This driver is for the switch-mode battery charger and boost
+ * hardware found in pmi8998 and related PMICs.
+ */
+
+#include <linux/bits.h>
+#include <linux/devm-helpers.h>
+#include <linux/iio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm_wakeirq.h>
+#include <linux/of.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+
+/* clang-format off */
+#define BATTERY_CHARGER_STATUS_1			0x06
+#define BVR_INITIAL_RAMP_BIT				BIT(7)
+#define CC_SOFT_TERMINATE_BIT				BIT(6)
+#define STEP_CHARGING_STATUS_SHIFT			3
+#define STEP_CHARGING_STATUS_MASK			GENMASK(5, 3)
+#define BATTERY_CHARGER_STATUS_MASK			GENMASK(2, 0)
+
+#define BATTERY_CHARGER_STATUS_2			0x07
+#define INPUT_CURRENT_LIMITED_BIT			BIT(7)
+#define CHARGER_ERROR_STATUS_SFT_EXPIRE_BIT		BIT(6)
+#define CHARGER_ERROR_STATUS_BAT_OV_BIT			BIT(5)
+#define CHARGER_ERROR_STATUS_BAT_TERM_MISSING_BIT	BIT(4)
+#define BAT_TEMP_STATUS_MASK				GENMASK(3, 0)
+#define BAT_TEMP_STATUS_SOFT_LIMIT_MASK			GENMASK(3, 2)
+#define BAT_TEMP_STATUS_HOT_SOFT_LIMIT_BIT		BIT(3)
+#define BAT_TEMP_STATUS_COLD_SOFT_LIMIT_BIT		BIT(2)
+#define BAT_TEMP_STATUS_TOO_HOT_BIT			BIT(1)
+#define BAT_TEMP_STATUS_TOO_COLD_BIT			BIT(0)
+
+#define BATTERY_CHARGER_STATUS_4			0x0A
+#define CHARGE_CURRENT_POST_JEITA_MASK			GENMASK(7, 0)
+
+#define BATTERY_CHARGER_STATUS_7			0x0D
+#define ENABLE_TRICKLE_BIT				BIT(7)
+#define ENABLE_PRE_CHARGING_BIT				BIT(6)
+#define ENABLE_FAST_CHARGING_BIT			BIT(5)
+#define ENABLE_FULLON_MODE_BIT				BIT(4)
+#define TOO_COLD_ADC_BIT				BIT(3)
+#define TOO_HOT_ADC_BIT					BIT(2)
+#define HOT_SL_ADC_BIT					BIT(1)
+#define COLD_SL_ADC_BIT					BIT(0)
+
+#define CHARGING_ENABLE_CMD				0x42
+#define CHARGING_ENABLE_CMD_BIT				BIT(0)
+
+#define CHGR_CFG2					0x51
+#define CHG_EN_SRC_BIT					BIT(7)
+#define CHG_EN_POLARITY_BIT				BIT(6)
+#define PRETOFAST_TRANSITION_CFG_BIT			BIT(5)
+#define BAT_OV_ECC_BIT					BIT(4)
+#define I_TERM_BIT					BIT(3)
+#define AUTO_RECHG_BIT					BIT(2)
+#define EN_ANALOG_DROP_IN_VBATT_BIT			BIT(1)
+#define CHARGER_INHIBIT_BIT				BIT(0)
+
+#define PRE_CHARGE_CURRENT_CFG				0x60
+#define PRE_CHARGE_CURRENT_SETTING_MASK			GENMASK(5, 0)
+
+#define FAST_CHARGE_CURRENT_CFG				0x61
+#define FAST_CHARGE_CURRENT_SETTING_MASK		GENMASK(7, 0)
+
+#define FLOAT_VOLTAGE_CFG				0x70
+#define FLOAT_VOLTAGE_SETTING_MASK			GENMASK(7, 0)
+
+#define FG_UPDATE_CFG_2_SEL				0x7D
+#define SOC_LT_OTG_THRESH_SEL_BIT			BIT(3)
+#define SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT		BIT(2)
+#define VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT		BIT(1)
+#define IBT_LT_CHG_TERM_THRESH_SEL_BIT			BIT(0)
+
+#define JEITA_EN_CFG					0x90
+#define JEITA_EN_HARDLIMIT_BIT				BIT(4)
+#define JEITA_EN_HOT_SL_FCV_BIT				BIT(3)
+#define JEITA_EN_COLD_SL_FCV_BIT			BIT(2)
+#define JEITA_EN_HOT_SL_CCC_BIT				BIT(1)
+#define JEITA_EN_COLD_SL_CCC_BIT			BIT(0)
+
+#define INT_RT_STS					0x310
+#define TYPE_C_CHANGE_RT_STS_BIT			BIT(7)
+#define USBIN_ICL_CHANGE_RT_STS_BIT			BIT(6)
+#define USBIN_SOURCE_CHANGE_RT_STS_BIT			BIT(5)
+#define USBIN_PLUGIN_RT_STS_BIT				BIT(4)
+#define USBIN_OV_RT_STS_BIT				BIT(3)
+#define USBIN_UV_RT_STS_BIT				BIT(2)
+#define USBIN_LT_3P6V_RT_STS_BIT			BIT(1)
+#define USBIN_COLLAPSE_RT_STS_BIT			BIT(0)
+
+#define OTG_CFG						0x153
+#define OTG_RESERVED_MASK				GENMASK(7, 6)
+#define DIS_OTG_ON_TLIM_BIT				BIT(5)
+#define QUICKSTART_OTG_FASTROLESWAP_BIT			BIT(4)
+#define INCREASE_DFP_TIME_BIT				BIT(3)
+#define ENABLE_OTG_IN_DEBUG_MODE_BIT			BIT(2)
+#define OTG_EN_SRC_CFG_BIT				BIT(1)
+#define CONCURRENT_MODE_CFG_BIT				BIT(0)
+
+#define OTG_ENG_OTG_CFG					0x1C0
+#define ENG_BUCKBOOST_HALT1_8_MODE_BIT			BIT(0)
+
+#define APSD_STATUS					0x307
+#define APSD_STATUS_7_BIT				BIT(7)
+#define HVDCP_CHECK_TIMEOUT_BIT				BIT(6)
+#define SLOW_PLUGIN_TIMEOUT_BIT				BIT(5)
+#define ENUMERATION_DONE_BIT				BIT(4)
+#define VADP_CHANGE_DONE_AFTER_AUTH_BIT			BIT(3)
+#define QC_AUTH_DONE_STATUS_BIT				BIT(2)
+#define QC_CHARGER_BIT					BIT(1)
+#define APSD_DTC_STATUS_DONE_BIT			BIT(0)
+
+#define APSD_RESULT_STATUS				0x308
+#define ICL_OVERRIDE_LATCH_BIT				BIT(7)
+#define APSD_RESULT_STATUS_MASK				GENMASK(6, 0)
+#define QC_3P0_BIT					BIT(6)
+#define QC_2P0_BIT					BIT(5)
+#define FLOAT_CHARGER_BIT				BIT(4)
+#define DCP_CHARGER_BIT					BIT(3)
+#define CDP_CHARGER_BIT					BIT(2)
+#define OCP_CHARGER_BIT					BIT(1)
+#define SDP_CHARGER_BIT					BIT(0)
+
+#define TYPE_C_STATUS_1					0x30B
+#define UFP_TYPEC_MASK					GENMASK(7, 5)
+#define UFP_TYPEC_RDSTD_BIT				BIT(7)
+#define UFP_TYPEC_RD1P5_BIT				BIT(6)
+#define UFP_TYPEC_RD3P0_BIT				BIT(5)
+#define UFP_TYPEC_FMB_255K_BIT				BIT(4)
+#define UFP_TYPEC_FMB_301K_BIT				BIT(3)
+#define UFP_TYPEC_FMB_523K_BIT				BIT(2)
+#define UFP_TYPEC_FMB_619K_BIT				BIT(1)
+#define UFP_TYPEC_OPEN_OPEN_BIT				BIT(0)
+
+#define TYPE_C_STATUS_2					0x30C
+#define DFP_RA_OPEN_BIT					BIT(7)
+#define TIMER_STAGE_BIT					BIT(6)
+#define EXIT_UFP_MODE_BIT				BIT(5)
+#define EXIT_DFP_MODE_BIT				BIT(4)
+#define DFP_TYPEC_MASK					GENMASK(3, 0)
+#define DFP_RD_OPEN_BIT					BIT(3)
+#define DFP_RD_RA_VCONN_BIT				BIT(2)
+#define DFP_RD_RD_BIT					BIT(1)
+#define DFP_RA_RA_BIT					BIT(0)
+
+#define TYPE_C_STATUS_3					0x30D
+#define ENABLE_BANDGAP_BIT				BIT(7)
+#define U_USB_GND_NOVBUS_BIT				BIT(6)
+#define U_USB_FLOAT_NOVBUS_BIT				BIT(5)
+#define U_USB_GND_BIT					BIT(4)
+#define U_USB_FMB1_BIT					BIT(3)
+#define U_USB_FLOAT1_BIT				BIT(2)
+#define U_USB_FMB2_BIT					BIT(1)
+#define U_USB_FLOAT2_BIT				BIT(0)
+
+#define TYPE_C_STATUS_4					0x30E
+#define UFP_DFP_MODE_STATUS_BIT				BIT(7)
+#define TYPEC_VBUS_STATUS_BIT				BIT(6)
+#define TYPEC_VBUS_ERROR_STATUS_BIT			BIT(5)
+#define TYPEC_DEBOUNCE_DONE_STATUS_BIT			BIT(4)
+#define TYPEC_UFP_AUDIO_ADAPT_STATUS_BIT		BIT(3)
+#define TYPEC_VCONN_OVERCURR_STATUS_BIT			BIT(2)
+#define CC_ORIENTATION_BIT				BIT(1)
+#define CC_ATTACHED_BIT					BIT(0)
+
+#define TYPE_C_STATUS_5					0x30F
+#define TRY_SOURCE_FAILED_BIT				BIT(6)
+#define TRY_SINK_FAILED_BIT				BIT(5)
+#define TIMER_STAGE_2_BIT				BIT(4)
+#define TYPEC_LEGACY_CABLE_STATUS_BIT			BIT(3)
+#define TYPEC_NONCOMP_LEGACY_CABLE_STATUS_BIT		BIT(2)
+#define TYPEC_TRYSOURCE_DETECT_STATUS_BIT		BIT(1)
+#define TYPEC_TRYSINK_DETECT_STATUS_BIT			BIT(0)
+
+#define CMD_APSD					0x341
+#define ICL_OVERRIDE_BIT				BIT(1)
+#define APSD_RERUN_BIT					BIT(0)
+
+#define TYPE_C_CFG					0x358
+#define APSD_START_ON_CC_BIT				BIT(7)
+#define WAIT_FOR_APSD_BIT				BIT(6)
+#define FACTORY_MODE_DETECTION_EN_BIT			BIT(5)
+#define FACTORY_MODE_ICL_3A_4A_BIT			BIT(4)
+#define FACTORY_MODE_DIS_CHGING_CFG_BIT			BIT(3)
+#define SUSPEND_NON_COMPLIANT_CFG_BIT			BIT(2)
+#define VCONN_OC_CFG_BIT				BIT(1)
+#define TYPE_C_OR_U_USB_BIT				BIT(0)
+
+#define TYPE_C_CFG_2					0x359
+#define TYPE_C_DFP_CURRSRC_MODE_BIT			BIT(7)
+#define DFP_CC_1P4V_OR_1P6V_BIT				BIT(6)
+#define VCONN_SOFTSTART_CFG_MASK			GENMASK(5, 4)
+#define EN_TRY_SOURCE_MODE_BIT				BIT(3)
+#define USB_FACTORY_MODE_ENABLE_BIT			BIT(2)
+#define TYPE_C_UFP_MODE_BIT				BIT(1)
+#define EN_80UA_180UA_CUR_SOURCE_BIT			BIT(0)
+
+#define TYPE_C_CFG_3					0x35A
+#define TVBUS_DEBOUNCE_BIT				BIT(7)
+#define TYPEC_LEGACY_CABLE_INT_EN_BIT			BIT(6)
+#define TYPEC_NONCOMPLIANT_LEGACY_CABLE_INT_EN_B	BIT(5)
+#define TYPEC_TRYSOURCE_DETECT_INT_EN_BIT		BIT(4)
+#define TYPEC_TRYSINK_DETECT_INT_EN_BIT			BIT(3)
+#define EN_TRYSINK_MODE_BIT				BIT(2)
+#define EN_LEGACY_CABLE_DETECTION_BIT			BIT(1)
+#define ALLOW_PD_DRING_UFP_TCCDB_BIT			BIT(0)
+
+#define USBIN_OPTIONS_1_CFG				0x362
+#define CABLE_R_SEL_BIT					BIT(7)
+#define HVDCP_AUTH_ALG_EN_CFG_BIT			BIT(6)
+#define HVDCP_AUTONOMOUS_MODE_EN_CFG_BIT		BIT(5)
+#define INPUT_PRIORITY_BIT				BIT(4)
+#define AUTO_SRC_DETECT_BIT				BIT(3)
+#define HVDCP_EN_BIT					BIT(2)
+#define VADP_INCREMENT_VOLTAGE_LIMIT_BIT		BIT(1)
+#define VADP_TAPER_TIMER_EN_BIT				BIT(0)
+
+#define USBIN_OPTIONS_2_CFG				0x363
+#define WIPWR_RST_EUD_CFG_BIT				BIT(7)
+#define SWITCHER_START_CFG_BIT				BIT(6)
+#define DCD_TIMEOUT_SEL_BIT				BIT(5)
+#define OCD_CURRENT_SEL_BIT				BIT(4)
+#define SLOW_PLUGIN_TIMER_EN_CFG_BIT			BIT(3)
+#define FLOAT_OPTIONS_MASK				GENMASK(2, 0)
+#define FLOAT_DIS_CHGING_CFG_BIT			BIT(2)
+#define SUSPEND_FLOAT_CFG_BIT				BIT(1)
+#define FORCE_FLOAT_SDP_CFG_BIT				BIT(0)
+
+#define TAPER_TIMER_SEL_CFG				0x364
+#define TYPEC_SPARE_CFG_BIT				BIT(7)
+#define TYPEC_DRP_DFP_TIME_CFG_BIT			BIT(5)
+#define TAPER_TIMER_SEL_MASK				GENMASK(1, 0)
+
+#define USBIN_LOAD_CFG					0x365
+#define USBIN_OV_CH_LOAD_OPTION_BIT			BIT(7)
+#define ICL_OVERRIDE_AFTER_APSD_BIT			BIT(4)
+
+#define USBIN_ICL_OPTIONS				0x366
+#define CFG_USB3P0_SEL_BIT				BIT(2)
+#define USB51_MODE_BIT					BIT(1)
+#define USBIN_MODE_CHG_BIT				BIT(0)
+
+#define TYPE_C_INTRPT_ENB_SOFTWARE_CTRL			0x368
+#define EXIT_SNK_BASED_ON_CC_BIT			BIT(7)
+#define VCONN_EN_ORIENTATION_BIT			BIT(6)
+#define TYPEC_VCONN_OVERCURR_INT_EN_BIT			BIT(5)
+#define VCONN_EN_SRC_BIT				BIT(4)
+#define VCONN_EN_VALUE_BIT				BIT(3)
+#define TYPEC_POWER_ROLE_CMD_MASK			GENMASK(2, 0)
+#define UFP_EN_CMD_BIT					BIT(2)
+#define DFP_EN_CMD_BIT					BIT(1)
+#define TYPEC_DISABLE_CMD_BIT				BIT(0)
+
+#define USBIN_CURRENT_LIMIT_CFG				0x370
+#define USBIN_CURRENT_LIMIT_MASK			GENMASK(7, 0)
+
+#define USBIN_AICL_OPTIONS_CFG				0x380
+#define SUSPEND_ON_COLLAPSE_USBIN_BIT			BIT(7)
+#define USBIN_AICL_HDC_EN_BIT				BIT(6)
+#define USBIN_AICL_START_AT_MAX_BIT			BIT(5)
+#define USBIN_AICL_RERUN_EN_BIT				BIT(4)
+#define USBIN_AICL_ADC_EN_BIT				BIT(3)
+#define USBIN_AICL_EN_BIT				BIT(2)
+#define USBIN_HV_COLLAPSE_RESPONSE_BIT			BIT(1)
+#define USBIN_LV_COLLAPSE_RESPONSE_BIT			BIT(0)
+
+#define USBIN_5V_AICL_THRESHOLD_CFG			0x381
+#define USBIN_5V_AICL_THRESHOLD_CFG_MASK		GENMASK(2, 0)
+
+#define USBIN_CONT_AICL_THRESHOLD_CFG			0x384
+#define USBIN_CONT_AICL_THRESHOLD_CFG_MASK		GENMASK(5, 0)
+
+#define DC_ENG_SSUPPLY_CFG2				0x4C1
+#define ENG_SSUPPLY_IVREF_OTG_SS_MASK			GENMASK(2, 0)
+#define OTG_SS_SLOW					0x3
+
+#define DCIN_AICL_REF_SEL_CFG				0x481
+#define DCIN_CONT_AICL_THRESHOLD_CFG_MASK		GENMASK(5, 0)
+
+#define WI_PWR_OPTIONS					0x495
+#define CHG_OK_BIT					BIT(7)
+#define WIPWR_UVLO_IRQ_OPT_BIT				BIT(6)
+#define BUCK_HOLDOFF_ENABLE_BIT				BIT(5)
+#define CHG_OK_HW_SW_SELECT_BIT				BIT(4)
+#define WIPWR_RST_ENABLE_BIT				BIT(3)
+#define DCIN_WIPWR_IRQ_SELECT_BIT			BIT(2)
+#define AICL_SWITCH_ENABLE_BIT				BIT(1)
+#define ZIN_ICL_ENABLE_BIT				BIT(0)
+
+#define ICL_STATUS					0x607
+#define INPUT_CURRENT_LIMIT_MASK			GENMASK(7, 0)
+
+#define POWER_PATH_STATUS				0x60B
+#define P_PATH_INPUT_SS_DONE_BIT			BIT(7)
+#define P_PATH_USBIN_SUSPEND_STS_BIT			BIT(6)
+#define P_PATH_DCIN_SUSPEND_STS_BIT			BIT(5)
+#define P_PATH_USE_USBIN_BIT				BIT(4)
+#define P_PATH_USE_DCIN_BIT				BIT(3)
+#define P_PATH_POWER_PATH_MASK				GENMASK(2, 1)
+#define P_PATH_VALID_INPUT_POWER_SOURCE_STS_BIT		BIT(0)
+
+#define BARK_BITE_WDOG_PET				0x643
+#define BARK_BITE_WDOG_PET_BIT				BIT(0)
+
+#define WD_CFG						0x651
+#define WATCHDOG_TRIGGER_AFP_EN_BIT			BIT(7)
+#define BARK_WDOG_INT_EN_BIT				BIT(6)
+#define BITE_WDOG_INT_EN_BIT				BIT(5)
+#define SFT_AFTER_WDOG_IRQ_MASK				GENMASK(4, 3)
+#define WDOG_IRQ_SFT_BIT				BIT(2)
+#define WDOG_TIMER_EN_ON_PLUGIN_BIT			BIT(1)
+#define WDOG_TIMER_EN_BIT				BIT(0)
+
+#define SNARL_BARK_BITE_WD_CFG				0x653
+#define BITE_WDOG_DISABLE_CHARGING_CFG_BIT		BIT(7)
+#define SNARL_WDOG_TIMEOUT_MASK				GENMASK(6, 4)
+#define BARK_WDOG_TIMEOUT_MASK				GENMASK(3, 2)
+#define BITE_WDOG_TIMEOUT_MASK				GENMASK(1, 0)
+
+#define AICL_RERUN_TIME_CFG				0x661
+#define AICL_RERUN_TIME_MASK				GENMASK(1, 0)
+
+#define STAT_CFG					0x690
+#define STAT_SW_OVERRIDE_VALUE_BIT			BIT(7)
+#define STAT_SW_OVERRIDE_CFG_BIT			BIT(6)
+#define STAT_PARALLEL_OFF_DG_CFG_MASK			GENMASK(5, 4)
+#define STAT_POLARITY_CFG_BIT				BIT(3)
+#define STAT_PARALLEL_CFG_BIT				BIT(2)
+#define STAT_FUNCTION_CFG_BIT				BIT(1)
+#define STAT_IRQ_PULSING_EN_BIT				BIT(0)
+
+#define SDP_CURRENT_UA					500000
+#define CDP_CURRENT_UA					1500000
+#define DCP_CURRENT_UA					1500000
+#define CURRENT_MAX_UA					DCP_CURRENT_UA
+
+/* pmi8998 registers represent current in increments of 1/40th of an amp */
+#define CURRENT_SCALE_FACTOR				25000
+/* clang-format on */
+
+enum charger_status {
+	TRICKLE_CHARGE = 0,
+	PRE_CHARGE,
+	FAST_CHARGE,
+	FULLON_CHARGE,
+	TAPER_CHARGE,
+	TERMINATE_CHARGE,
+	INHIBIT_CHARGE,
+	DISABLE_CHARGE,
+};
+
+struct smb2_register {
+	u16 addr;
+	u8 mask;
+	u8 val;
+};
+
+/**
+ * struct smb2_chip - smb2 chip structure
+ * @dev:		Device reference for power_supply
+ * @name:		The platform device name
+ * @base:		Base address for smb2 registers
+ * @regmap:		Register map
+ * @batt_info:		Battery data from DT
+ * @status_change_work: Worker to handle plug/unplug events
+ * @cable_irq:		USB plugin IRQ
+ * @wakeup_enabled:	If the cable IRQ will cause a wakeup
+ * @usb_in_i_chan:	USB_IN current measurement channel
+ * @usb_in_v_chan:	USB_IN voltage measurement channel
+ * @chg_psy:		Charger power supply instance
+ */
+struct smb2_chip {
+	struct device *dev;
+	const char *name;
+	unsigned int base;
+	struct regmap *regmap;
+	struct power_supply_battery_info *batt_info;
+
+	struct delayed_work status_change_work;
+	int cable_irq;
+	bool wakeup_enabled;
+
+	struct iio_channel *usb_in_i_chan;
+	struct iio_channel *usb_in_v_chan;
+
+	struct power_supply *chg_psy;
+};
+
+static enum power_supply_property smb2_properties[] = {
+	POWER_SUPPLY_PROP_MANUFACTURER,
+	POWER_SUPPLY_PROP_MODEL_NAME,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_USB_TYPE,
+	POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT,
+	POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX,
+};
+
+static enum power_supply_usb_type smb2_usb_types[] = {
+	POWER_SUPPLY_USB_TYPE_UNKNOWN,
+	POWER_SUPPLY_USB_TYPE_SDP,
+	POWER_SUPPLY_USB_TYPE_DCP,
+	POWER_SUPPLY_USB_TYPE_CDP,
+};
+
+static int smb2_get_prop_usb_online(struct smb2_chip *chip, int *val)
+{
+	unsigned int stat;
+	int rc;
+
+	rc = regmap_read(chip->regmap, chip->base + POWER_PATH_STATUS, &stat);
+	if (rc < 0) {
+		dev_err(chip->dev, "Couldn't read power path status: %d\n", rc);
+		return rc;
+	}
+
+	*val = (stat & P_PATH_USE_USBIN_BIT) &&
+	       (stat & P_PATH_VALID_INPUT_POWER_SOURCE_STS_BIT);
+	return 0;
+}
+
+/*
+ * Qualcomm "automatic power source detection" aka APSD
+ * tells us what type of charger we're connected to.
+ */
+static int smb2_apsd_get_charger_type(struct smb2_chip *chip, int *val)
+{
+	unsigned int apsd_stat, stat;
+	int usb_online = 0;
+	int rc;
+
+	rc = smb2_get_prop_usb_online(chip, &usb_online);
+	if (!usb_online) {
+		*val = POWER_SUPPLY_USB_TYPE_UNKNOWN;
+		return rc;
+	}
+
+	rc = regmap_read(chip->regmap, chip->base + APSD_STATUS, &apsd_stat);
+	if (rc < 0) {
+		dev_err(chip->dev, "Failed to read apsd status, rc = %d", rc);
+		return rc;
+	}
+	if (!(apsd_stat & APSD_DTC_STATUS_DONE_BIT)) {
+		dev_dbg(chip->dev, "Apsd not ready");
+		return -EAGAIN;
+	}
+
+	rc = regmap_read(chip->regmap, chip->base + APSD_RESULT_STATUS, &stat);
+	if (rc < 0) {
+		dev_err(chip->dev, "Failed to read apsd result, rc = %d", rc);
+		return rc;
+	}
+
+	stat &= APSD_RESULT_STATUS_MASK;
+
+	if (stat & CDP_CHARGER_BIT)
+		*val = POWER_SUPPLY_USB_TYPE_CDP;
+	else if (stat & (DCP_CHARGER_BIT | OCP_CHARGER_BIT | FLOAT_CHARGER_BIT))
+		*val = POWER_SUPPLY_USB_TYPE_DCP;
+	else /* SDP_CHARGER_BIT (or others) */
+		*val = POWER_SUPPLY_USB_TYPE_SDP;
+
+	return 0;
+}
+
+static int smb2_get_prop_status(struct smb2_chip *chip, int *val)
+{
+	unsigned char stat[2];
+	int usb_online = 0;
+	int rc;
+
+	rc = smb2_get_prop_usb_online(chip, &usb_online);
+	if (!usb_online) {
+		*val = POWER_SUPPLY_STATUS_DISCHARGING;
+		return rc;
+	}
+
+	rc = regmap_bulk_read(chip->regmap,
+			      chip->base + BATTERY_CHARGER_STATUS_1, &stat, 2);
+	if (rc < 0) {
+		dev_err(chip->dev, "Failed to read charging status ret=%d\n",
+			rc);
+		return rc;
+	}
+
+	if (stat[1] & CHARGER_ERROR_STATUS_BAT_OV_BIT) {
+		*val = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		return 0;
+	}
+
+	stat[0] = stat[0] & BATTERY_CHARGER_STATUS_MASK;
+
+	switch (stat[0]) {
+	case TRICKLE_CHARGE:
+	case PRE_CHARGE:
+	case FAST_CHARGE:
+	case FULLON_CHARGE:
+	case TAPER_CHARGE:
+		*val = POWER_SUPPLY_STATUS_CHARGING;
+		return rc;
+	case DISABLE_CHARGE:
+		*val = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		return rc;
+	case TERMINATE_CHARGE:
+		*val = POWER_SUPPLY_STATUS_FULL;
+		return rc;
+	case INHIBIT_CHARGE:
+	default:
+		*val = POWER_SUPPLY_STATUS_UNKNOWN;
+		return rc;
+	}
+}
+
+static inline int smb2_get_current_limit(struct smb2_chip *chip,
+					 unsigned int *val)
+{
+	int rc = regmap_read(chip->regmap, chip->base + ICL_STATUS, val);
+
+	if (rc >= 0)
+		*val *= CURRENT_SCALE_FACTOR;
+	return rc;
+}
+
+static int smb2_set_current_limit(struct smb2_chip *chip, unsigned int val)
+{
+	unsigned char val_raw;
+
+	if (val > 4800000) {
+		dev_err(chip->dev,
+			"Can't set current limit higher than 4800000uA");
+		return -EINVAL;
+	}
+	val_raw = val / CURRENT_SCALE_FACTOR;
+
+	return regmap_write(chip->regmap, chip->base + USBIN_CURRENT_LIMIT_CFG,
+			    val_raw);
+}
+
+static void smb2_status_change_work(struct work_struct *work)
+{
+	unsigned int charger_type, current_ua;
+	int usb_online, count, rc;
+	struct smb2_chip *chip;
+
+	chip = container_of(work, struct smb2_chip, status_change_work.work);
+
+	smb2_get_prop_usb_online(chip, &usb_online);
+	if (!usb_online)
+		return;
+
+	for (count = 0; count < 3; count++) {
+		dev_dbg(chip->dev, "get charger type retry %d\n", count);
+		rc = smb2_apsd_get_charger_type(chip, &charger_type);
+		if (rc != -EAGAIN)
+			break;
+		msleep(100);
+	}
+
+	if (rc < 0 && rc != -EAGAIN) {
+		dev_err(chip->dev, "get charger type failed: %d\n", rc);
+		return;
+	}
+
+	if (rc < 0) {
+		rc = regmap_update_bits(chip->regmap, chip->base + CMD_APSD,
+					APSD_RERUN_BIT, APSD_RERUN_BIT);
+		schedule_delayed_work(&chip->status_change_work,
+				      msecs_to_jiffies(1000));
+		dev_dbg(chip->dev, "get charger type failed, rerun apsd\n");
+		return;
+	}
+
+	switch (charger_type) {
+	case POWER_SUPPLY_USB_TYPE_CDP:
+		current_ua = CDP_CURRENT_UA;
+		break;
+	case POWER_SUPPLY_USB_TYPE_DCP:
+		current_ua = DCP_CURRENT_UA;
+		break;
+	case POWER_SUPPLY_USB_TYPE_SDP:
+	default:
+		current_ua = SDP_CURRENT_UA;
+		break;
+	}
+
+	smb2_set_current_limit(chip, current_ua);
+	power_supply_changed(chip->chg_psy);
+}
+
+static int smb2_get_iio_chan(struct smb2_chip *chip, struct iio_channel *chan,
+			     int *val)
+{
+	int rc;
+	union power_supply_propval status;
+
+	rc = power_supply_get_property(chip->chg_psy, POWER_SUPPLY_PROP_STATUS,
+				       &status);
+	if (rc < 0 || status.intval != POWER_SUPPLY_STATUS_CHARGING) {
+		*val = 0;
+		return 0;
+	}
+
+	if (IS_ERR(chan)) {
+		dev_err(chip->dev, "Failed to chan, err = %li", PTR_ERR(chan));
+		return PTR_ERR(chan);
+	}
+
+	return iio_read_channel_processed(chan, val);
+}
+
+static int smb2_get_prop_health(struct smb2_chip *chip, int *val)
+{
+	int rc;
+	unsigned int stat;
+
+	rc = regmap_read(chip->regmap, chip->base + BATTERY_CHARGER_STATUS_2,
+			 &stat);
+	if (rc < 0) {
+		dev_err(chip->dev, "Couldn't read charger status rc=%d\n", rc);
+		return rc;
+	}
+
+	switch (stat) {
+	case CHARGER_ERROR_STATUS_BAT_OV_BIT:
+		*val = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+		return 0;
+	case BAT_TEMP_STATUS_TOO_COLD_BIT:
+		*val = POWER_SUPPLY_HEALTH_COLD;
+		return 0;
+	case BAT_TEMP_STATUS_TOO_HOT_BIT:
+		*val = POWER_SUPPLY_HEALTH_OVERHEAT;
+		return 0;
+	case BAT_TEMP_STATUS_COLD_SOFT_LIMIT_BIT:
+		*val = POWER_SUPPLY_HEALTH_COOL;
+		return 0;
+	case BAT_TEMP_STATUS_HOT_SOFT_LIMIT_BIT:
+		*val = POWER_SUPPLY_HEALTH_WARM;
+		return 0;
+	default:
+		*val = POWER_SUPPLY_HEALTH_GOOD;
+		return 0;
+	}
+}
+
+static int smb2_get_property(struct power_supply *psy,
+			     enum power_supply_property psp,
+			     union power_supply_propval *val)
+{
+	struct smb2_chip *chip = power_supply_get_drvdata(psy);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = "Qualcomm";
+		return 0;
+	case POWER_SUPPLY_PROP_MODEL_NAME:
+		val->strval = chip->name;
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		return smb2_get_current_limit(chip, &val->intval);
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX:
+		val->intval = DCP_CURRENT_UA;
+		return 0;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		return smb2_get_iio_chan(chip, chip->usb_in_i_chan,
+					 &val->intval);
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		return smb2_get_iio_chan(chip, chip->usb_in_v_chan,
+					 &val->intval);
+	case POWER_SUPPLY_PROP_ONLINE:
+		return smb2_get_prop_usb_online(chip, &val->intval);
+	case POWER_SUPPLY_PROP_STATUS:
+		return smb2_get_prop_status(chip, &val->intval);
+	case POWER_SUPPLY_PROP_HEALTH:
+		return smb2_get_prop_health(chip, &val->intval);
+	case POWER_SUPPLY_PROP_USB_TYPE:
+		return smb2_apsd_get_charger_type(chip, &val->intval);
+	default:
+		dev_err(chip->dev, "invalid property: %d\n", psp);
+		return -EINVAL;
+	}
+}
+
+static int smb2_set_property(struct power_supply *psy,
+			     enum power_supply_property psp,
+			     const union power_supply_propval *val)
+{
+	struct smb2_chip *chip = power_supply_get_drvdata(psy);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		return smb2_set_current_limit(chip, val->intval);
+	default:
+		dev_err(chip->dev, "No setter for property: %d\n", psp);
+		return -EINVAL;
+	}
+}
+
+static int smb2_property_is_writable(struct power_supply *psy,
+				     enum power_supply_property psp)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CURRENT_MAX:
+	case POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT:
+		return 1;
+	default:
+		return 0;
+	}
+}
+
+static irqreturn_t smb2_handle_batt_overvoltage(int irq, void *data)
+{
+	struct smb2_chip *chip = data;
+	unsigned int status;
+
+	regmap_read(chip->regmap, chip->base + BATTERY_CHARGER_STATUS_2,
+		    &status);
+
+	if (status & CHARGER_ERROR_STATUS_BAT_OV_BIT) {
+		/* The hardware stops charging automatically */
+		dev_err(chip->dev, "battery overvoltage detected\n");
+		power_supply_changed(chip->chg_psy);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smb2_handle_usb_plugin(int irq, void *data)
+{
+	struct smb2_chip *chip = data;
+
+	power_supply_changed(chip->chg_psy);
+
+	schedule_delayed_work(&chip->status_change_work,
+			      msecs_to_jiffies(1500));
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smb2_handle_usb_icl_change(int irq, void *data)
+{
+	struct smb2_chip *chip = data;
+
+	power_supply_changed(chip->chg_psy);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t smb2_handle_wdog_bark(int irq, void *data)
+{
+	struct smb2_chip *chip = data;
+	int rc;
+
+	power_supply_changed(chip->chg_psy);
+
+	rc = regmap_write(chip->regmap, BARK_BITE_WDOG_PET,
+			  BARK_BITE_WDOG_PET_BIT);
+	if (rc < 0)
+		dev_err(chip->dev, "Couldn't pet the dog rc=%d\n", rc);
+
+	return IRQ_HANDLED;
+}
+
+static const struct power_supply_desc smb2_psy_desc = {
+	.name = "pmi8998_charger",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.usb_types = smb2_usb_types,
+	.num_usb_types = ARRAY_SIZE(smb2_usb_types),
+	.properties = smb2_properties,
+	.num_properties = ARRAY_SIZE(smb2_properties),
+	.get_property = smb2_get_property,
+	.set_property = smb2_set_property,
+	.property_is_writeable = smb2_property_is_writable,
+};
+
+/* Init sequence derived from vendor downstream driver */
+static const struct smb2_register smb2_init_seq[] = {
+	{ .addr = AICL_RERUN_TIME_CFG, .mask = AICL_RERUN_TIME_MASK, .val = 0 },
+	/*
+	 * By default configure us as an upstream facing port
+	 * FIXME: This will be handled by the type-c driver
+	 */
+	{ .addr = TYPE_C_INTRPT_ENB_SOFTWARE_CTRL,
+	  .mask = TYPEC_POWER_ROLE_CMD_MASK | VCONN_EN_SRC_BIT |
+		  VCONN_EN_VALUE_BIT,
+	  .val = VCONN_EN_SRC_BIT },
+	/*
+	 * Disable Type-C factory mode and stay in Attached.SRC state when VCONN
+	 * over-current happens
+	 */
+	{ .addr = TYPE_C_CFG,
+	  .mask = FACTORY_MODE_DETECTION_EN_BIT | VCONN_OC_CFG_BIT,
+	  .val = 0 },
+	/* Configure VBUS for software control */
+	{ .addr = OTG_CFG, .mask = OTG_EN_SRC_CFG_BIT, .val = 0 },
+	/*
+	 * Use VBAT to determine the recharge threshold when battery is full
+	 * rather than the state of charge.
+	 */
+	{ .addr = FG_UPDATE_CFG_2_SEL,
+	  .mask = SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT |
+		  VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT,
+	  .val = VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT },
+	/* Enable charging */
+	{ .addr = USBIN_OPTIONS_1_CFG, .mask = HVDCP_EN_BIT, .val = 0 },
+	{ .addr = CHARGING_ENABLE_CMD,
+	  .mask = CHARGING_ENABLE_CMD_BIT,
+	  .val = CHARGING_ENABLE_CMD_BIT },
+	/*
+	 * Match downstream defaults
+	 * CHG_EN_SRC_BIT - charger enable is controlled by software
+	 * CHG_EN_POLARITY_BIT - polarity of charge enable pin when in HW control
+	 *                       pulled low on OnePlus 6 and SHIFT6mq
+	 * PRETOFAST_TRANSITION_CFG_BIT -
+	 * BAT_OV_ECC_BIT -
+	 * I_TERM_BIT - Current termination ?? 0 = enabled
+	 * AUTO_RECHG_BIT - Enable automatic recharge when battery is full
+	 *                  0 = enabled
+	 * EN_ANALOG_DROP_IN_VBATT_BIT
+	 * CHARGER_INHIBIT_BIT - Inhibit charging based on battery voltage
+	 *                       instead of ??
+	 */
+	{ .addr = CHGR_CFG2,
+	  .mask = CHG_EN_SRC_BIT | CHG_EN_POLARITY_BIT |
+		  PRETOFAST_TRANSITION_CFG_BIT | BAT_OV_ECC_BIT | I_TERM_BIT |
+		  AUTO_RECHG_BIT | EN_ANALOG_DROP_IN_VBATT_BIT |
+		  CHARGER_INHIBIT_BIT,
+	  .val = CHARGER_INHIBIT_BIT },
+	/* STAT pin software override, match downstream. Parallell charging? */
+	{ .addr = STAT_CFG,
+	  .mask = STAT_SW_OVERRIDE_CFG_BIT,
+	  .val = STAT_SW_OVERRIDE_CFG_BIT },
+	/* Set the default SDP charger type to a 500ma USB 2.0 port */
+	{ .addr = USBIN_ICL_OPTIONS,
+	  .mask = USB51_MODE_BIT | USBIN_MODE_CHG_BIT,
+	  .val = USB51_MODE_BIT },
+	/* Disable watchdog */
+	{ .addr = SNARL_BARK_BITE_WD_CFG, .mask = 0xff, .val = 0 },
+	{ .addr = WD_CFG,
+	  .mask = WATCHDOG_TRIGGER_AFP_EN_BIT | WDOG_TIMER_EN_ON_PLUGIN_BIT |
+		  BARK_WDOG_INT_EN_BIT,
+	  .val = 0 },
+	/* These bits aren't documented anywhere */
+	{ .addr = USBIN_5V_AICL_THRESHOLD_CFG,
+	  .mask = USBIN_5V_AICL_THRESHOLD_CFG_MASK,
+	  .val = 0x3 },
+	{ .addr = USBIN_CONT_AICL_THRESHOLD_CFG,
+	  .mask = USBIN_CONT_AICL_THRESHOLD_CFG_MASK,
+	  .val = 0x3 },
+	/*
+	 * Enable Automatic Input Current Limit, this will slowly ramp up the current
+	 * When connected to a wall charger, and automatically stop when it detects
+	 * the charger current limit (voltage drop?) or it reaches the programmed limit.
+	 */
+	{ .addr = USBIN_AICL_OPTIONS_CFG,
+	  .mask = USBIN_AICL_START_AT_MAX_BIT | USBIN_AICL_ADC_EN_BIT |
+		  USBIN_AICL_EN_BIT | SUSPEND_ON_COLLAPSE_USBIN_BIT |
+		  USBIN_HV_COLLAPSE_RESPONSE_BIT |
+		  USBIN_LV_COLLAPSE_RESPONSE_BIT,
+	  .val = USBIN_HV_COLLAPSE_RESPONSE_BIT |
+		 USBIN_LV_COLLAPSE_RESPONSE_BIT | USBIN_AICL_EN_BIT },
+	/*
+	 * Set pre charge current to default, the OnePlus 6 bootloader
+	 * sets this very conservatively.
+	 */
+	{ .addr = PRE_CHARGE_CURRENT_CFG,
+	  .mask = PRE_CHARGE_CURRENT_SETTING_MASK,
+	  .val = 500000 / CURRENT_SCALE_FACTOR },
+	/*
+	 * This overrides all of the current limit options exposed to userspace
+	 * and prevents the device from pulling more than ~1A. This is done
+	 * to minimise potential fire hazard risks.
+	 */
+	{ .addr = FAST_CHARGE_CURRENT_CFG,
+	  .mask = FAST_CHARGE_CURRENT_SETTING_MASK,
+	  .val = 1000000 / CURRENT_SCALE_FACTOR },
+};
+
+static int smb2_init_hw(struct smb2_chip *chip)
+{
+	int rc, i;
+
+	for (i = 0; i < ARRAY_SIZE(smb2_init_seq); i++) {
+		dev_dbg(chip->dev, "%d: Writing 0x%02x to 0x%02x\n", i,
+			smb2_init_seq[i].val, smb2_init_seq[i].addr);
+		rc = regmap_update_bits(chip->regmap,
+					chip->base + smb2_init_seq[i].addr,
+					smb2_init_seq[i].mask,
+					smb2_init_seq[i].val);
+		if (rc < 0)
+			return dev_err_probe(chip->dev, rc,
+					     "%s: init command %d failed\n",
+					     __func__, i);
+	}
+
+	return 0;
+}
+
+static int smb2_init_irq(struct smb2_chip *chip, int *irq, const char *name,
+			 irqreturn_t (*handler)(int irq, void *data))
+{
+	int irqnum;
+	int rc;
+
+	irqnum = platform_get_irq_byname(to_platform_device(chip->dev), name);
+	if (irqnum < 0)
+		return dev_err_probe(chip->dev, irqnum,
+				     "Couldn't get irq %s byname\n", name);
+
+	rc = devm_request_threaded_irq(chip->dev, irqnum, NULL, handler,
+				       IRQF_ONESHOT, name, chip);
+	if (rc < 0)
+		return dev_err_probe(chip->dev, rc, "Couldn't request irq %s\n",
+				     name);
+
+	if (irq)
+		*irq = irqnum;
+
+	return 0;
+}
+
+static int smb2_probe(struct platform_device *pdev)
+{
+	struct power_supply_config supply_config = {};
+	struct power_supply_desc *desc;
+	struct smb2_chip *chip;
+	int rc, irq;
+
+	chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = &pdev->dev;
+	chip->name = pdev->name;
+
+	chip->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!chip->regmap)
+		return dev_err_probe(chip->dev, -ENODEV,
+				     "failed to locate the regmap\n");
+
+	rc = device_property_read_u32(chip->dev, "reg", &chip->base);
+	if (rc < 0)
+		return dev_err_probe(chip->dev, rc,
+				     "Couldn't read base address\n");
+
+	chip->usb_in_v_chan = devm_iio_channel_get(chip->dev, "usbin_v");
+	if (IS_ERR(chip->usb_in_v_chan))
+		return dev_err_probe(chip->dev, PTR_ERR(chip->usb_in_v_chan),
+				     "Couldn't get usbin_v IIO channel\n");
+
+	chip->usb_in_i_chan = devm_iio_channel_get(chip->dev, "usbin_i");
+	if (IS_ERR(chip->usb_in_i_chan)) {
+		return dev_err_probe(chip->dev, PTR_ERR(chip->usb_in_i_chan),
+				     "Couldn't get usbin_i IIO channel\n");
+	}
+
+	rc = smb2_init_hw(chip);
+	if (rc < 0)
+		return rc;
+
+	supply_config.drv_data = chip;
+	supply_config.of_node = pdev->dev.of_node;
+
+	desc = devm_kzalloc(chip->dev, sizeof(smb2_psy_desc), GFP_KERNEL);
+	memcpy(desc, &smb2_psy_desc, sizeof(smb2_psy_desc));
+	desc->name =
+		devm_kasprintf(chip->dev, GFP_KERNEL, "%s-charger",
+			       (const char *)device_get_match_data(chip->dev));
+
+	chip->chg_psy =
+		devm_power_supply_register(chip->dev, desc, &supply_config);
+	if (IS_ERR(chip->chg_psy))
+		return dev_err_probe(chip->dev, PTR_ERR(chip->chg_psy),
+				     "failed to register power supply\n");
+
+	rc = power_supply_get_battery_info(chip->chg_psy, &chip->batt_info);
+	if (rc)
+		return dev_err_probe(chip->dev, rc,
+				     "Failed to get battery info\n");
+
+	rc = devm_delayed_work_autocancel(chip->dev, &chip->status_change_work,
+					  smb2_status_change_work);
+	if (rc)
+		return dev_err_probe(chip->dev, rc,
+				     "Failed to init status change work\n");
+
+	rc = (chip->batt_info->voltage_max_design_uv - 3487500) / 7500 + 1;
+	rc = regmap_update_bits(chip->regmap, chip->base + FLOAT_VOLTAGE_CFG,
+				FLOAT_VOLTAGE_SETTING_MASK, rc);
+	if (rc < 0)
+		return dev_err_probe(chip->dev, rc, "Couldn't set vbat max\n");
+
+	rc = smb2_init_irq(chip, &irq, "bat-ov", smb2_handle_batt_overvoltage);
+	if (rc < 0)
+		return rc;
+
+	rc = smb2_init_irq(chip, &chip->cable_irq, "usb-plugin",
+			   smb2_handle_usb_plugin);
+	if (rc < 0)
+		return rc;
+
+	rc = smb2_init_irq(chip, &irq, "usbin-icl-change",
+			   smb2_handle_usb_icl_change);
+	if (rc < 0)
+		return rc;
+	rc = smb2_init_irq(chip, &irq, "wdog-bark", smb2_handle_wdog_bark);
+	if (rc < 0)
+		return rc;
+
+	rc = dev_pm_set_wake_irq(chip->dev, chip->cable_irq);
+	if (rc < 0)
+		return dev_err_probe(chip->dev, rc, "Couldn't set wake irq\n");
+
+	platform_set_drvdata(pdev, chip);
+
+	/* Initialise charger state */
+	schedule_delayed_work(&chip->status_change_work, 0);
+
+	return 0;
+}
+
+static const struct of_device_id smb2_match_id_table[] = {
+	{ .compatible = "qcom,pmi8998-charger", .data = "pmi8998" },
+	{ .compatible = "qcom,pm660-charger", .data = "pm660" },
+	{ /* sentinal */ }
+};
+MODULE_DEVICE_TABLE(of, smb2_match_id_table);
+
+static struct platform_driver qcom_spmi_smb2 = {
+	.probe = smb2_probe,
+	.driver = {
+		.name = "qcom-pmi8998/pm660-charger",
+		.of_match_table = smb2_match_id_table,
+		},
+};
+
+module_platform_driver(qcom_spmi_smb2);
+
+MODULE_AUTHOR("Caleb Connolly <caleb.connolly@linaro.org>");
+MODULE_DESCRIPTION("Qualcomm SMB2 Charger Driver");
+MODULE_LICENSE("GPL");