@@ -15,6 +15,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp418.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp433.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp449.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp453.dtb
+dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp454.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb
new file mode 100644
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ9574 RDP454 board device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq9574.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9";
+ compatible = "qcom,ipq9574-ap-al02-c9", "qcom,ipq9574";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&blsp1_spi0 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash@0 {
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-mp5496-regulators";
+
+ ipq9574_s1: s1 {
+ /*
+ * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders.
+ * During regulator registration, kernel not knowing the initial voltage,
+ * considers it as zero and brings up the regulators with minimum supported voltage.
+ * Update the regulator-min-microvolt with SVS voltage of 725mV so that
+ * the regulators are brought up with 725mV which is sufficient for all the
+ * corner parts to operate at 800MHz
+ */
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1075000>;
+ };
+ };
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ spi_0_pins: spi-0-state {
+ pins = "gpio11", "gpio12", "gpio13", "gpio14";
+ function = "blsp0_spi";
+ drive-strength = <8>;
+ bias-disable;
+ };
+};
+
+&xo_board_clk {
+ clock-frequency = <24000000>;
+};
Add the initial device tree support for the Reference Design Platform (RDP) 454 based on IPQ9574 family of SoCs. This patch adds support for Console UART, SPI NOR and SMPA1 regulator node. Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com> --- Changes in V2: - Dropped cpu_opp_table entries as it will be handled based on fuse values in a seperate series. arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts | 80 +++++++++++++++++++++ 2 files changed, 81 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts