diff mbox series

[V1,2/2] mmc: sdhci-pci-o2micro: add Bayhub new chip GG8 support

Message ID 20230607014812.30104-2-chevron_li@126.com
State New
Headers show
Series [V1,1/2] mmc: sdhci-pci-o2micro: add Bayhub new chip GG8 support | expand

Commit Message

Chevron Li June 7, 2023, 1:48 a.m. UTC 
From: Chevron Li <chevron.li@bayhubtech.com>

Add Bayhub new chip GG8 support for SD express card.
This patch depends on patch 1/2.

Signed-off-by: Chevron Li <chevron.li@bayhubtech.com>
---
Change in V1:
1.Implement the SD express card callback routine.
2.Add SD express card support for Bayhub GG8 chip.
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 61 +++++++++++++++++++++++++++-
 1 file changed, 60 insertions(+), 1 deletion(-)

Comments

Chevron Li (WH) June 14, 2023, 1:45 a.m. UTC | #1 
Hi, Adrian/Ulf,

May I know the patch progress?
Look forward your response.

BR,
Chevron

-----Original Message-----
From: Chevron Li <chevron_li@126.com> 
Sent: Wednesday, June 7, 2023 9:48
To: adrian.hunter@intel.com; ulf.hansson@linaro.org; linux-mmc@vger.kernel.org; linux-kernel@vger.kernel.org
Cc: Shaper Liu (WH) <shaper.liu@bayhubtech.com>; XiaoGuang Yu (WH) <xiaoguang.yu@bayhubtech.com>; Shirley Her(SC) <shirley.her@bayhubtech.com>; Chevron Li (WH) <chevron.li@bayhubtech.com>
Subject: [PATCH V1 2/2] mmc: sdhci-pci-o2micro: add Bayhub new chip GG8 support

From: Chevron Li <chevron.li@bayhubtech.com>

Add Bayhub new chip GG8 support for SD express card.
This patch depends on patch 1/2.

Signed-off-by: Chevron Li <chevron.li@bayhubtech.com>
---
Change in V1:
1.Implement the SD express card callback routine.
2.Add SD express card support for Bayhub GG8 chip.
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 61 +++++++++++++++++++++++++++-
 1 file changed, 60 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index 8243a63b3c81..b2d8ddbb4095 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -21,6 +21,7 @@
  * O2Micro device registers
  */
 
+#define O2_SD_PCIE_SWITCH	0x54
 #define O2_SD_MISC_REG5		0x64
 #define O2_SD_LD0_CTRL		0x68
 #define O2_SD_DEV_CTRL		0x88
@@ -631,6 +632,63 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
 	sdhci_o2_enable_clk(host, clk);
 }
 
+static u8 sdhci_o2_sd_express_clkq_assert(struct sdhci_host *host) {
+	return sdhci_readb(host, O2_SD_EXP_INT_REG); }
+
+static int sdhci_pci_o2_init_sd_express(struct mmc_host *mmc, struct 
+mmc_ios *ios) {
+	struct sdhci_host *host = mmc_priv(mmc);
+	struct sdhci_pci_slot *slot = sdhci_priv(host);
+	struct sdhci_pci_chip *chip = slot->chip;
+	u8 scratch8 = 0;
+	u16 scratch16 = 0;
+	bool ret = false;
+
+	/* Disable clock */
+	sdhci_writeb(host, 0, SDHCI_CLOCK_CONTROL);
+
+	/* Set VDD2 voltage*/
+	scratch8 = sdhci_readb(host, SDHCI_POWER_CONTROL);
+	scratch8 &= 0x0F;
+	if ((host->mmc->ios.timing == MMC_TIMING_SD_EXP_1_2V) &&
+		(host->mmc->caps2 & MMC_CAP2_SD_EXP_1_2V)) {
+		scratch8 |= BIT(4) | BIT(7);
+	} else
+		scratch8 |= BIT(4) | BIT(5) | BIT(7);
+	sdhci_writeb(host, scratch8, SDHCI_POWER_CONTROL);
+
+	/* UnLock WP */
+	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch8);
+	scratch8 &= 0x7f;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch8);
+
+	ret = readx_poll_timeout(sdhci_o2_sd_express_clkq_assert, host,
+		scratch8, !(scratch8 & BIT(0)), 1, 30000) == 0 ? 0 : 1;
+
+	if (!ret) {
+		/* switch to PCIe mode */
+		scratch16 = sdhci_readw(host, O2_SD_PCIE_SWITCH);
+		scratch16 |= BIT(8);
+		sdhci_writew(host, scratch16, O2_SD_PCIE_SWITCH);
+	} else {
+		/* keep mode as USHI */
+		pci_read_config_word(chip->pdev,
+						O2_SD_PARA_SET_REG1, &scratch16);
+		scratch16 &= ~BIT(11);
+		pci_write_config_word(chip->pdev,
+						O2_SD_PARA_SET_REG1, scratch16);
+	}
+	/* Lock WP */
+	pci_read_config_byte(chip->pdev,
+					O2_SD_LOCK_WP, &scratch8);
+	scratch8 |= 0x80;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch8);
+
+	return ret;
+}
+
 static int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)  {
 	struct sdhci_pci_chip *chip;
@@ -703,10 +761,11 @@ static int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 	case PCI_DEVICE_ID_O2_GG8_9861:
 	case PCI_DEVICE_ID_O2_GG8_9862:
 	case PCI_DEVICE_ID_O2_GG8_9863:
-		host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
+		host->mmc->caps2 |= MMC_CAP2_NO_SDIO | MMC_CAP2_SD_EXP | 
+MMC_CAP2_SD_EXP_1_2V;
 		host->mmc->caps |= MMC_CAP_HW_RESET;
 		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
 		slot->host->mmc_host_ops.get_cd = sdhci_o2_get_cd;
+		host->mmc_host_ops.init_sd_express = sdhci_pci_o2_init_sd_express;
 		break;
 	default:
 		break;
--
2.25.1
Adrian Hunter June 14, 2023, 7:30 a.m. UTC | #2 
On 7/06/23 04:48, Chevron Li wrote:
> From: Chevron Li <chevron.li@bayhubtech.com>
> 
> Add Bayhub new chip GG8 support for SD express card.
> This patch depends on patch 1/2.

Patch subject should be different from patch 1

> 
> Signed-off-by: Chevron Li <chevron.li@bayhubtech.com>

Some comments below.

> ---
> Change in V1:
> 1.Implement the SD express card callback routine.
> 2.Add SD express card support for Bayhub GG8 chip.
> ---
>  drivers/mmc/host/sdhci-pci-o2micro.c | 61 +++++++++++++++++++++++++++-
>  1 file changed, 60 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index 8243a63b3c81..b2d8ddbb4095 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -21,6 +21,7 @@
>   * O2Micro device registers
>   */
>  
> +#define O2_SD_PCIE_SWITCH	0x54
>  #define O2_SD_MISC_REG5		0x64
>  #define O2_SD_LD0_CTRL		0x68
>  #define O2_SD_DEV_CTRL		0x88
> @@ -631,6 +632,63 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
>  	sdhci_o2_enable_clk(host, clk);
>  }
>  
> +static u8 sdhci_o2_sd_express_clkq_assert(struct sdhci_host *host)
> +{
> +	return sdhci_readb(host, O2_SD_EXP_INT_REG);
> +}
> +
> +static int sdhci_pci_o2_init_sd_express(struct mmc_host *mmc, struct mmc_ios *ios)
> +{
> +	struct sdhci_host *host = mmc_priv(mmc);
> +	struct sdhci_pci_slot *slot = sdhci_priv(host);
> +	struct sdhci_pci_chip *chip = slot->chip;
> +	u8 scratch8 = 0;
> +	u16 scratch16 = 0;
> +	bool ret = false;

ret should be an int and does not need to be initialized.

> +
> +	/* Disable clock */
> +	sdhci_writeb(host, 0, SDHCI_CLOCK_CONTROL);
> +
> +	/* Set VDD2 voltage*/
> +	scratch8 = sdhci_readb(host, SDHCI_POWER_CONTROL);
> +	scratch8 &= 0x0F;
> +	if ((host->mmc->ios.timing == MMC_TIMING_SD_EXP_1_2V) &&
> +		(host->mmc->caps2 & MMC_CAP2_SD_EXP_1_2V)) {

Unnecessary parentheses

> +		scratch8 |= BIT(4) | BIT(7);
> +	} else

braces {} should be used on all arms of this statement

Have a look at the output of checkpatch.pl --strict

There are "Alignment should match open parenthesis"
messages also

> +		scratch8 |= BIT(4) | BIT(5) | BIT(7);

Please use SDHCI_VDD2_POWER_ON, SDHCI_VDD2_POWER_120, SDHCI_VDD2_POWER_180


> +	sdhci_writeb(host, scratch8, SDHCI_POWER_CONTROL);
> +
> +	/* UnLock WP */
> +	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch8);
> +	scratch8 &= 0x7f;
> +	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch8);
> +
> +	ret = readx_poll_timeout(sdhci_o2_sd_express_clkq_assert, host,
> +		scratch8, !(scratch8 & BIT(0)), 1, 30000) == 0 ? 0 : 1;

This can use read_poll_timeout() then sdhci_o2_sd_express_clkq_assert()
is not needed.  And the ' == 0 ? 0 : 1' does not seem needed.

> +
> +	if (!ret) {
> +		/* switch to PCIe mode */
> +		scratch16 = sdhci_readw(host, O2_SD_PCIE_SWITCH);
> +		scratch16 |= BIT(8);
> +		sdhci_writew(host, scratch16, O2_SD_PCIE_SWITCH);
> +	} else {
> +		/* keep mode as USHI */

USHI ?

Do you intend to fall back to SD mode here? Because
returning non-zero will cause the initialization to
fail.  To continue to initialize SD mode, it looks
like you need to change host->ios.timing = MMC_TIMING_LEGACY
and return 0

> +		pci_read_config_word(chip->pdev,
> +						O2_SD_PARA_SET_REG1, &scratch16);

Unneeded line break

> +		scratch16 &= ~BIT(11);
> +		pci_write_config_word(chip->pdev,
> +						O2_SD_PARA_SET_REG1, scratch16);

Unneeded line break

> +	}
> +	/* Lock WP */
> +	pci_read_config_byte(chip->pdev,
> +					O2_SD_LOCK_WP, &scratch8);
> +	scratch8 |= 0x80;
> +	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch8);
> +
> +	return ret;
> +}
> +
>  static int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
>  {
>  	struct sdhci_pci_chip *chip;
> @@ -703,10 +761,11 @@ static int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
>  	case PCI_DEVICE_ID_O2_GG8_9861:
>  	case PCI_DEVICE_ID_O2_GG8_9862:
>  	case PCI_DEVICE_ID_O2_GG8_9863:
> -		host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
> +		host->mmc->caps2 |= MMC_CAP2_NO_SDIO | MMC_CAP2_SD_EXP | MMC_CAP2_SD_EXP_1_2V;
>  		host->mmc->caps |= MMC_CAP_HW_RESET;
>  		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
>  		slot->host->mmc_host_ops.get_cd = sdhci_o2_get_cd;
> +		host->mmc_host_ops.init_sd_express = sdhci_pci_o2_init_sd_express;
>  		break;
>  	default:
>  		break;
diff mbox series

Patch

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index 8243a63b3c81..b2d8ddbb4095 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -21,6 +21,7 @@ 
  * O2Micro device registers
  */
 
+#define O2_SD_PCIE_SWITCH	0x54
 #define O2_SD_MISC_REG5		0x64
 #define O2_SD_LD0_CTRL		0x68
 #define O2_SD_DEV_CTRL		0x88
@@ -631,6 +632,63 @@  static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
 	sdhci_o2_enable_clk(host, clk);
 }
 
+static u8 sdhci_o2_sd_express_clkq_assert(struct sdhci_host *host)
+{
+	return sdhci_readb(host, O2_SD_EXP_INT_REG);
+}
+
+static int sdhci_pci_o2_init_sd_express(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	struct sdhci_pci_slot *slot = sdhci_priv(host);
+	struct sdhci_pci_chip *chip = slot->chip;
+	u8 scratch8 = 0;
+	u16 scratch16 = 0;
+	bool ret = false;
+
+	/* Disable clock */
+	sdhci_writeb(host, 0, SDHCI_CLOCK_CONTROL);
+
+	/* Set VDD2 voltage*/
+	scratch8 = sdhci_readb(host, SDHCI_POWER_CONTROL);
+	scratch8 &= 0x0F;
+	if ((host->mmc->ios.timing == MMC_TIMING_SD_EXP_1_2V) &&
+		(host->mmc->caps2 & MMC_CAP2_SD_EXP_1_2V)) {
+		scratch8 |= BIT(4) | BIT(7);
+	} else
+		scratch8 |= BIT(4) | BIT(5) | BIT(7);
+	sdhci_writeb(host, scratch8, SDHCI_POWER_CONTROL);
+
+	/* UnLock WP */
+	pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch8);
+	scratch8 &= 0x7f;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch8);
+
+	ret = readx_poll_timeout(sdhci_o2_sd_express_clkq_assert, host,
+		scratch8, !(scratch8 & BIT(0)), 1, 30000) == 0 ? 0 : 1;
+
+	if (!ret) {
+		/* switch to PCIe mode */
+		scratch16 = sdhci_readw(host, O2_SD_PCIE_SWITCH);
+		scratch16 |= BIT(8);
+		sdhci_writew(host, scratch16, O2_SD_PCIE_SWITCH);
+	} else {
+		/* keep mode as USHI */
+		pci_read_config_word(chip->pdev,
+						O2_SD_PARA_SET_REG1, &scratch16);
+		scratch16 &= ~BIT(11);
+		pci_write_config_word(chip->pdev,
+						O2_SD_PARA_SET_REG1, scratch16);
+	}
+	/* Lock WP */
+	pci_read_config_byte(chip->pdev,
+					O2_SD_LOCK_WP, &scratch8);
+	scratch8 |= 0x80;
+	pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch8);
+
+	return ret;
+}
+
 static int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 {
 	struct sdhci_pci_chip *chip;
@@ -703,10 +761,11 @@  static int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 	case PCI_DEVICE_ID_O2_GG8_9861:
 	case PCI_DEVICE_ID_O2_GG8_9862:
 	case PCI_DEVICE_ID_O2_GG8_9863:
-		host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
+		host->mmc->caps2 |= MMC_CAP2_NO_SDIO | MMC_CAP2_SD_EXP | MMC_CAP2_SD_EXP_1_2V;
 		host->mmc->caps |= MMC_CAP_HW_RESET;
 		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
 		slot->host->mmc_host_ops.get_cd = sdhci_o2_get_cd;
+		host->mmc_host_ops.init_sd_express = sdhci_pci_o2_init_sd_express;
 		break;
 	default:
 		break;