diff mbox series

[v6,6/9] mmc: mmci: Retry the busy start condition

Message ID 20230405-pl180-busydetect-fix-v6-6-b850ec8019f3@linaro.org
State New
Headers show
Series Fix busydetect on Ux500 PL180/MMCI | expand

Commit Message

Linus Walleij June 16, 2023, 8:30 a.m. UTC
This makes the ux500 ->busy_complete() callback re-read
the status register 10 times while waiting for the busy
signal to assert in the status register.

If this does not happen, we bail out regarding the
command completed already, i.e. before we managed to
start to check the busy status.

There is a comment in the code about this, let's just
implement it to be certain that we can catch this glitch
if it happens.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v4->v6:
- No changes.
ChangeLog v3->v4:
- Accumulate status flags outside the if()-clause in the
  busy detect retry loop.
ChangeLog v2->v3:
- Rebased.
ChangeLog v1->v2:
- Move over the initial saving of host->busy_status from
  an unrelated patch to this one: it is clear what we are
  doing: we don't want to miss any transient
  (MCI_CMDSENT | MCI_CMDRESPEND) in the status register.
---
 drivers/mmc/host/mmci.c | 39 +++++++++++++++++++++++++++------------
 1 file changed, 27 insertions(+), 12 deletions(-)
diff mbox series

Patch

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index ccfca055f9a1..6ae56c973b0d 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -664,6 +664,7 @@  static u32 ux500v2_get_dctrl_cfg(struct mmci_host *host)
 static bool ux500_busy_complete(struct mmci_host *host, u32 status, u32 err_msk)
 {
 	void __iomem *base = host->base;
+	int retries = 10;
 
 	if (status & err_msk) {
 		/* Stop any ongoing busy detection if an error occurs */
@@ -684,21 +685,35 @@  static bool ux500_busy_complete(struct mmci_host *host, u32 status, u32 err_msk)
 	 * Note that, the card may need a couple of clock cycles before
 	 * it starts signaling busy on DAT0, hence re-read the
 	 * MMCISTATUS register here, to allow the busy bit to be set.
-	 * Potentially we may even need to poll the register for a
-	 * while, to allow it to be set, but tests indicates that it
-	 * isn't needed.
 	 */
 	if (host->busy_state == MMCI_BUSY_DONE) {
-		status = readl(base + MMCISTATUS);
-		if (status & host->variant->busy_detect_flag) {
-			writel(readl(base + MMCIMASK0) |
-			       host->variant->busy_detect_mask,
-			       base + MMCIMASK0);
-
-			host->busy_status = status & (MCI_CMDSENT | MCI_CMDRESPEND);
-			host->busy_state = MMCI_BUSY_WAITING_FOR_START_IRQ;
-			return false;
+		/*
+		 * Save the first status register read to be sure to catch
+		 * all bits that may be lost will retrying. If the command
+		 * is still busy this will result in assigning 0 to
+		 * host->busy_status, which is what it should be in IDLE.
+		 */
+		host->busy_status = status & (MCI_CMDSENT | MCI_CMDRESPEND);
+		while (retries) {
+			status = readl(base + MMCISTATUS);
+			/* Keep accumulating status bits */
+			host->busy_status |= status & (MCI_CMDSENT | MCI_CMDRESPEND);
+			if (status & host->variant->busy_detect_flag) {
+				writel(readl(base + MMCIMASK0) |
+				       host->variant->busy_detect_mask,
+				       base + MMCIMASK0);
+				host->busy_state = MMCI_BUSY_WAITING_FOR_START_IRQ;
+				return false;
+			}
+			retries--;
 		}
+		dev_dbg(mmc_dev(host->mmc), "no busy signalling in time\n");
+		writel(host->variant->busy_detect_mask, base + MMCICLEAR);
+		writel(readl(base + MMCIMASK0) &
+		       ~host->variant->busy_detect_mask, base + MMCIMASK0);
+		host->busy_state = MMCI_BUSY_DONE;
+		host->busy_status = 0;
+		return true;
 	}
 
 	/*