diff mbox series

media: ov5640: Fix initial RESETB state and annotate timings

Message ID 20230724222116.162555-1-marex@denx.de
State Accepted
Commit a210df337c5f5c2cd82f36c9dbb154ec63365c80
Headers show
Series media: ov5640: Fix initial RESETB state and annotate timings | expand

Commit Message

Marek Vasut July 24, 2023, 10:21 p.m. UTC
The initial state of RESETB input signal of OV5640 should be
asserted, i.e. the sensor should be in reset. This is not the
case, make it so.

Since the subsequent assertion of RESETB signal is no longer
necessary and the timing of the power sequencing could be
slightly adjusted, add annotations to the delays which match
OV5640 datasheet rev. 2.03, both:
  figure 2-3 power up timing with internal DVDD
  figure 2-4 power up timing with external DVDD source

The 5..10ms delay between PWDN assertion and RESETB assertion
is not even documented in the power sequencing diagram, and
with this reset fix, it is no longer even necessary.

Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Marek Vasut <marex@denx.de>
---
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Cc: linux-media@vger.kernel.org
---
 drivers/media/i2c/ov5640.c | 11 ++++-------
 1 file changed, 4 insertions(+), 7 deletions(-)
diff mbox series

Patch

diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
index 7c065c39082dd..74b58380b5e69 100644
--- a/drivers/media/i2c/ov5640.c
+++ b/drivers/media/i2c/ov5640.c
@@ -2452,16 +2452,13 @@  static void ov5640_power(struct ov5640_dev *sensor, bool enable)
 static void ov5640_powerup_sequence(struct ov5640_dev *sensor)
 {
 	if (sensor->pwdn_gpio) {
-		gpiod_set_value_cansleep(sensor->reset_gpio, 0);
+		gpiod_set_value_cansleep(sensor->reset_gpio, 1);
 
 		/* camera power cycle */
 		ov5640_power(sensor, false);
-		usleep_range(5000, 10000);
+		usleep_range(5000, 10000);	/* t2 */
 		ov5640_power(sensor, true);
-		usleep_range(5000, 10000);
-
-		gpiod_set_value_cansleep(sensor->reset_gpio, 1);
-		usleep_range(1000, 2000);
+		usleep_range(1000, 2000);	/* t3 */
 
 		gpiod_set_value_cansleep(sensor->reset_gpio, 0);
 	} else {
@@ -2469,7 +2466,7 @@  static void ov5640_powerup_sequence(struct ov5640_dev *sensor)
 		ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0,
 				 OV5640_REG_SYS_CTRL0_SW_RST);
 	}
-	usleep_range(20000, 25000);
+	usleep_range(20000, 25000);	/* t4 */
 
 	/*
 	 * software standby: allows registers programming;