| Message ID | 20230807193507.6488-5-brgl@bgdev.pl |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: qcom: enable EMAC1 on sa8775p | expand |
On Mon, Aug 07, 2023 at 04:18:21PM -0500, Andrew Halaney wrote: > On Mon, Aug 07, 2023 at 09:35:02PM +0200, Bartosz Golaszewski wrote: > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > > > Add the MDC and MDIO pin functions for ethernet1 on sa8775p-ride. > > > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> > > --- > > arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 16 ++++++++++++++++ > > 1 file changed, 16 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts > > index 09ae6e153282..38327aff18b0 100644 > > --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts > > +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts > > @@ -480,6 +480,22 @@ ethernet0_mdio: ethernet0-mdio-pins { > > }; > > }; > > > > + ethernet1_default: ethernet1-default-state { > > + ethernet1_mdc: ethernet1-mdc-pins { > > + pins = "gpio20"; > > + function = "emac1_mdc"; > > + drive-strength = <16>; > > + bias-pull-up; > > + }; > > + > > + ethernet1_mdio: ethernet1-mdio-pins { > > + pins = "gpio21"; > > + function = "emac1_mdio"; > > + drive-strength = <16>; > > + bias-pull-up; > > + }; > > + }; > > + > > With the whole "EMAC0 MDIO handles the ethernet phy for EMAC1", this > doesn't seem to make sense. > > I don't have all the schematics, but these pins are not connected from > what I see. I kind of agree. I've seen different ways of describing pinmux. What i've done for Kirkwood was to put all the common pinmux configurations into the SoC .dtsi file. The .dts file can then reference it if needed. In this case, since the bus is unused, it seems odd to mux it. And later versions of the board could actually use the pins for something else, GPIOs etc. Andrew
diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts index 09ae6e153282..38327aff18b0 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts @@ -480,6 +480,22 @@ ethernet0_mdio: ethernet0-mdio-pins { }; }; + ethernet1_default: ethernet1-default-state { + ethernet1_mdc: ethernet1-mdc-pins { + pins = "gpio20"; + function = "emac1_mdc"; + drive-strength = <16>; + bias-pull-up; + }; + + ethernet1_mdio: ethernet1-mdio-pins { + pins = "gpio21"; + function = "emac1_mdio"; + drive-strength = <16>; + bias-pull-up; + }; + }; + qup_uart10_default: qup-uart10-state { pins = "gpio46", "gpio47"; function = "qup1_se3";