diff mbox series

[RESEND,v2,4/9] arm64: dts: qcom: Add pm7550ba PMIC dtsi

Message ID 1691415534-31820-5-git-send-email-quic_rohiagar@quicinc.com
State Superseded
Headers show
Series Add pmics supported in Qualcomm's SDX75 platform | expand

Commit Message

Rohit Agarwal Aug. 7, 2023, 1:38 p.m. UTC
Add dtsi for pm7550ba PMIC found in Qualcomm platforms.

Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
---
 arch/arm64/boot/dts/qcom/pm7550ba.dtsi | 70 ++++++++++++++++++++++++++++++++++
 1 file changed, 70 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm7550ba.dtsi
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/pm7550ba.dtsi b/arch/arm64/boot/dts/qcom/pm7550ba.dtsi
new file mode 100644
index 0000000..8b00ece
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm7550ba.dtsi
@@ -0,0 +1,70 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm7550ba-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm7550ba_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm7550ba: pmic@7 {
+		compatible = "qcom,pm7550ba", "qcom,spmi-pmic";
+		reg = <7 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm7550ba_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm7550ba_gpios: gpio@8800 {
+			compatible = "qcom,pm7550ba-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm7550ba_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm7550ba_eusb2_repeater: phy@fd00 {
+			compatible = "qcom,pm7550ba-eusb2-repeater", "qcom,pm8550b-eusb2-repeater";
+			reg = <0xfd00>;
+			#phy-cells = <0>;
+		};
+	};
+};