@@ -1038,6 +1038,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct msm_pinctrl *pctrl = gpiochip_get_data(gc);
const struct msm_pingroup *g;
+ u32 intr_target_mask = GENMASK(2, 0);
unsigned long flags;
bool was_enabled;
u32 val;
@@ -1074,13 +1075,15 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
* With intr_target_use_scm interrupts are routed to
* application cpu using scm calls.
*/
+ if (g->intr_target_width)
+ intr_target_mask = GENMASK(g->intr_target_width - 1, 0);
+
if (pctrl->intr_target_use_scm) {
u32 addr = pctrl->phys_base[0] + g->intr_target_reg;
int ret;
qcom_scm_io_readl(addr, &val);
-
- val &= ~(7 << g->intr_target_bit);
+ val &= ~(intr_target_mask << g->intr_target_bit);
val |= g->intr_target_kpss_val << g->intr_target_bit;
ret = qcom_scm_io_writel(addr, val);
@@ -1090,7 +1093,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
d->hwirq);
} else {
val = msm_readl_intr_target(pctrl, g);
- val &= ~(7 << g->intr_target_bit);
+ val &= ~(intr_target_mask << g->intr_target_bit);
val |= g->intr_target_kpss_val << g->intr_target_bit;
msm_writel_intr_target(val, pctrl, g);
}
@@ -59,6 +59,7 @@ struct pinctrl_pin_desc;
* @intr_status_bit: Offset in @intr_status_reg for reading and acking the interrupt
* status.
* @intr_target_bit: Offset in @intr_target_reg for configuring the interrupt routing.
+ * @intr_target_width: Number of bits used for specifying interrupt routing target.
* @intr_target_kpss_val: Value in @intr_target_bit for specifying that the interrupt from
* this gpio should get routed to the KPSS processor.
* @intr_raw_status_bit: Offset in @intr_cfg_reg for the raw status bit.
@@ -100,6 +101,7 @@ struct msm_pingroup {
unsigned intr_ack_high:1;
unsigned intr_target_bit:5;
+ unsigned intr_target_width:5;
unsigned intr_target_kpss_val:5;
unsigned intr_raw_status_bit:5;
unsigned intr_polarity_bit:5;
@@ -46,6 +46,7 @@
.intr_enable_bit = 0, \
.intr_status_bit = 0, \
.intr_target_bit = 5, \
+ .intr_target_width = 4, \
.intr_target_kpss_val = 3, \
.intr_raw_status_bit = 4, \
.intr_polarity_bit = 1, \
SA8775 and newer target have added support for an increased number of interrupt targets. To implement this change, the intr_target field, which is used to configure the interrupt target in the interrupt configuration register is increased from 3 bits to 4 bits. In accordance to these updates, a new intr_target_width member is introduced in msm_pingroup structure. This member stores the value of width of intr_target field in the interrupt configuration register. This value is used to dynamically calculate and generate mask for setting the intr_target field. By default, this mask is set to 3 bit wide, to ensure backward compatibility with the older targets. Fixes: 4b6b18559927 ("pinctrl: qcom: add the tlmm driver sa8775p platforms") Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride Signed-off-by: Ninad Naik <quic_ninanaik@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com> --- Changes in v3 : - Resend, by adding correct maintainers missed in v2. - v2 : https://lore.kernel.org/all/20230718064246.12429-1-quic_ninanaik@quicinc.com/ Changes in v2 : - Changed initial definition of intr_target_mask variable to use GENMASK(). - Update commit subject appropiately. - Add Fixes tag. - v1 : https://lore.kernel.org/all/20230714061010.15817-1-quic_ninanaik@quicinc.com/ drivers/pinctrl/qcom/pinctrl-msm.c | 9 ++++++--- drivers/pinctrl/qcom/pinctrl-msm.h | 2 ++ drivers/pinctrl/qcom/pinctrl-sa8775p.c | 1 + 3 files changed, 9 insertions(+), 3 deletions(-)