@@ -125,8 +125,10 @@ struct omap2_mcspi {
struct omap2_mcspi_dma *dma_channels;
struct device *dev;
struct omap2_mcspi_regs ctx;
+ struct clk *clk;
int fifo_depth;
bool slave_aborted;
+ unsigned int ref_clk_hz;
unsigned int pin_dir:1;
size_t max_xfer_len;
};
@@ -880,12 +882,12 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
return count - c;
}
-static u32 omap2_mcspi_calc_divisor(u32 speed_hz)
+static u32 omap2_mcspi_calc_divisor(u32 speed_hz, u32 ref_clk_hz)
{
u32 div;
for (div = 0; div < 15; div++)
- if (speed_hz >= (OMAP2_MCSPI_MAX_FREQ >> div))
+ if (speed_hz >= (ref_clk_hz >> div))
return div;
return 15;
@@ -897,7 +899,7 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
{
struct omap2_mcspi_cs *cs = spi->controller_state;
struct omap2_mcspi *mcspi;
- u32 l = 0, clkd = 0, div, extclk = 0, clkg = 0;
+ u32 ref_clk_hz, l = 0, clkd = 0, div, extclk = 0, clkg = 0;
u8 word_len = spi->bits_per_word;
u32 speed_hz = spi->max_speed_hz;
@@ -911,14 +913,15 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
if (t && t->speed_hz)
speed_hz = t->speed_hz;
- speed_hz = min_t(u32, speed_hz, OMAP2_MCSPI_MAX_FREQ);
- if (speed_hz < (OMAP2_MCSPI_MAX_FREQ / OMAP2_MCSPI_MAX_DIVIDER)) {
- clkd = omap2_mcspi_calc_divisor(speed_hz);
- speed_hz = OMAP2_MCSPI_MAX_FREQ >> clkd;
+ ref_clk_hz = mcspi->ref_clk_hz;
+ speed_hz = min_t(u32, speed_hz, ref_clk_hz);
+ if (speed_hz < (ref_clk_hz / OMAP2_MCSPI_MAX_DIVIDER)) {
+ clkd = omap2_mcspi_calc_divisor(speed_hz, ref_clk_hz);
+ speed_hz = ref_clk_hz >> clkd;
clkg = 0;
} else {
- div = (OMAP2_MCSPI_MAX_FREQ + speed_hz - 1) / speed_hz;
- speed_hz = OMAP2_MCSPI_MAX_FREQ / div;
+ div = (ref_clk_hz + speed_hz - 1) / speed_hz;
+ speed_hz = ref_clk_hz / div;
clkd = (div - 1) & 0xf;
extclk = (div - 1) >> 4;
clkg = OMAP2_MCSPI_CHCONF_CLKG;
@@ -1448,8 +1451,6 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
master->cleanup = omap2_mcspi_cleanup;
master->slave_abort = omap2_mcspi_slave_abort;
master->dev.of_node = node;
- master->max_speed_hz = OMAP2_MCSPI_MAX_FREQ;
- master->min_speed_hz = OMAP2_MCSPI_MAX_FREQ >> 15;
master->use_gpio_descriptors = true;
platform_set_drvdata(pdev, master);
@@ -1519,6 +1520,14 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
goto free_master;
}
+ mcspi->clk = devm_clk_get_optional_enabled(&pdev->dev, NULL);
+ if (mcspi->clk)
+ mcspi->ref_clk_hz = clk_get_rate(mcspi->clk);
+ else
+ mcspi->ref_clk_hz = OMAP2_MCSPI_MAX_FREQ;
+ master->max_speed_hz = mcspi->ref_clk_hz;
+ master->min_speed_hz = mcspi->ref_clk_hz >> 15;
+
pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
pm_runtime_enable(&pdev->dev);
A hardcoded reference clock of 48 MHz is used to calculate the clock divisor values, but the reference clock frequency can be different across devices and can be configured which can cause a mismatch between the reported frequency and actual SPI clock frequency observed. Fix this by fetching the clock rate from the clock provider and falling back to hardcoded reference only if the clock is not supplied. Fixes: 2cd7d393f461 ("arm64: dts: ti: k3-am654: Add McSPI DT nodes") Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com> --- Blamed commit is the first device where the default reference clock was different from the hardcoded value. Tested on TDA4VM SK (6.6.0-rc1-next-20230911) drivers/spi/spi-omap2-mcspi.c | 31 ++++++++++++++++++++----------- 1 file changed, 20 insertions(+), 11 deletions(-)