diff mbox series

[V3,3/3] arm64: dts: qcom: ipq5018: enable the CPUFreq support

Message ID 20230925102826.405446-4-quic_gokulsri@quicinc.com
State Accepted
Commit 3e4b53e04281ed3d9c7a4329c027097265c04d54
Headers show
Series Add APSS clock driver support for IPQ5018 | expand

Commit Message

Gokul Sriram Palanisamy Sept. 25, 2023, 10:28 a.m. UTC 
Add the APCS, A53 PLL, cpu-opp-table nodes to set
the CPU frequency at 800MHz (idle) or 1.008GHz.

Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/ipq5018.dtsi | 40 +++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

Comments

Krzysztof Kozlowski Sept. 25, 2023, 10:57 a.m. UTC | #1 
On 25/09/2023 12:28, Gokul Sriram Palanisamy wrote:
> Add the APCS, A53 PLL, cpu-opp-table nodes to set
> the CPU frequency at 800MHz (idle) or 1.008GHz.
> 
> Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 40 +++++++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 9f13d2dcdfd5..56f3c5260bbd 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -5,6 +5,7 @@ 
  * Copyright (c) 2023 The Linux Foundation. All rights reserved.
  */
 
+#include <dt-bindings/clock/qcom,apss-ipq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
 #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
@@ -36,6 +37,8 @@  CPU0: cpu@0 {
 			reg = <0x0>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
+			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
+			operating-points-v2 = <&cpu_opp_table>;
 		};
 
 		CPU1: cpu@1 {
@@ -44,6 +47,8 @@  CPU1: cpu@1 {
 			reg = <0x1>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
+			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
+			operating-points-v2 = <&cpu_opp_table>;
 		};
 
 		L2_0: l2-cache {
@@ -54,6 +59,23 @@  L2_0: l2-cache {
 		};
 	};
 
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <200000>;
+		};
+
+		opp-1008000000 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <200000>;
+		};
+	};
+
 	firmware {
 		scm {
 			compatible = "qcom,scm-ipq5018", "qcom,scm";
@@ -181,6 +203,24 @@  v2m1: v2m@1000 {
 			};
 		};
 
+		apcs_glb: mailbox@b111000 {
+			compatible = "qcom,ipq5018-apcs-apps-global",
+				     "qcom,ipq6018-apcs-apps-global";
+			reg = <0x0b111000 0x1000>;
+			#clock-cells = <1>;
+			clocks = <&a53pll>, <&xo_board_clk>, <&gcc GPLL0>;
+			clock-names = "pll", "xo", "gpll0";
+			#mbox-cells = <1>;
+		};
+
+		a53pll: clock@b116000 {
+			compatible = "qcom,ipq5018-a53pll";
+			reg = <0x0b116000 0x40>;
+			#clock-cells = <0>;
+			clocks = <&xo_board_clk>;
+			clock-names = "xo";
+		};
+
 		timer@b120000 {
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0b120000 0x1000>;