@@ -33,6 +33,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-clearfog.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb
fsl-ls1028a-qds-13bb-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-13bb.dtbo
new file mode 100644
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2162A Clearfog
+//
+// Copyright 2023 Josua Mayer <josua@solid-run.com>
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+#include "fsl-lx2162a-sr-som.dtsi"
+
+/ {
+ model = "SolidRun LX2162A Clearfog";
+ compatible = "solidrun,lx2162a-clearfog", "solidrun,lx2162a-som", "fsl,lx2160a";
+
+ aliases {
+ crypto = &crypto;
+ i2c0 = &i2c0;
+ i2c1 = &i2c2;
+ i2c2 = &i2c4;
+ i2c3 = &sfp_i2c0;
+ i2c4 = &sfp_i2c1;
+ i2c5 = &sfp_i2c2;
+ i2c6 = &sfp_i2c3;
+ i2c7 = &mpcie1_i2c;
+ i2c8 = &mpcie0_i2c;
+ i2c9 = &pcieclk_i2c;
+ mmc0 = &esdhc0;
+ mmc1 = &esdhc1;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_sfp_at: led-sfp-at {
+ gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* PROC_IRQ5 */
+ default-state = "off";
+ };
+
+ led_sfp_ab: led-sfp-ab {
+ gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>; /* PROC_IRQ11 */
+ default-state = "off";
+ };
+
+ led_sfp_bt: led-sfp-bt {
+ gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>; /* EVT1_B */
+ default-state = "off";
+ };
+
+ led_sfp_bb: led-sfp-bb {
+ gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>; /* EVT2_B */
+ default-state = "off";
+ };
+ };
+
+ sfp_at: sfp-at {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_i2c0>;
+ mod-def0-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>; /* EVT4_B */
+ maximum-power-milliwatt = <2000>;
+ };
+
+ sfp_ab: sfp-ab {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_i2c1>;
+ mod-def0-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; /* PROC_IRQ1 */
+ maximum-power-milliwatt = <2000>;
+ };
+
+ sfp_bt: sfp-bt {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_i2c2>;
+ mod-def0-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; /* PROC_IRQ10 */
+ maximum-power-milliwatt = <2000>;
+ };
+
+ sfp_bb: sfp-bb {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_i2c3>;
+ mod-def0-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; /* EVT3_B */
+ maximum-power-milliwatt = <2000>;
+ };
+};
+
+&dpmac3 {
+ sfp = <&sfp_at>;
+ managed = "in-band-status";
+ phys = <&serdes_1 7>;
+};
+
+&dpmac4 {
+ sfp = <&sfp_ab>;
+ managed = "in-band-status";
+ phys = <&serdes_1 6>;
+};
+
+&dpmac5 {
+ sfp = <&sfp_bt>;
+ managed = "in-band-status";
+ phys = <&serdes_1 5>;
+};
+
+&dpmac6 {
+ sfp = <&sfp_bb>;
+ managed = "in-band-status";
+ phys = <&serdes_1 4>;
+};
+
+&dpmac11 {
+ phys = <&serdes_2 0>;
+ phy-handle = <ðernet_phy3>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac12 {
+ phys = <&serdes_2 1>;
+ phy-handle = <ðernet_phy1>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac13 {
+ phys = <&serdes_2 6>;
+ phy-handle = <ðernet_phy6>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac14 {
+ phys = <&serdes_2 7>;
+ phy-handle = <ðernet_phy8>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac15 {
+ phys = <&serdes_2 4>;
+ phy-handle = <ðernet_phy4>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac16 {
+ phys = <&serdes_2 5>;
+ phy-handle = <ðernet_phy2>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac17 {
+ /* override connection to on-SoM phy */
+ /delete-property/ phy-handle;
+ /delete-property/ phy-connection-type;
+
+ phys = <&serdes_2 2>;
+ phy-handle = <ðernet_phy5>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&dpmac18 {
+ phys = <&serdes_2 3>;
+ phy-handle = <ðernet_phy7>;
+ phy-connection-type = "sgmii";
+ status = "okay";
+};
+
+&emdio1 {
+ ethernet_phy1: ethernet-phy@8 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <8>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy2: ethernet-phy@9 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <9>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy3: ethernet-phy@10 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <10>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy4: ethernet-phy@11 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <11>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy5: ethernet-phy@12 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <12>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy6: ethernet-phy@13 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <13>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy7: ethernet-phy@14 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <14>;
+ max-speed = <1000>;
+ };
+
+ ethernet_phy8: ethernet-phy@15 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <15>;
+ max-speed = <1000>;
+ };
+};
+
+&esdhc0 {
+ sd-uhs-sdr104;
+ sd-uhs-sdr50;
+ sd-uhs-sdr25;
+ sd-uhs-sdr12;
+ status = "okay";
+};
+
+ðernet_phy0 {
+ /*
+ * SoM has a phy at address 1 connected to SoC Ethernet Controller 1.
+ * It competes for WRIOP MAC17, and no connector has been wired.
+ */
+ status = "disabled";
+};
+
+&i2c2 {
+ status = "okay";
+
+ /* retimer@18 */
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ sfp_i2c0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ sfp_i2c1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ sfp_i2c2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ sfp_i2c3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@71 {
+ compatible = "nxp,pca9546";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ mpcie1_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ mpcie0_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ pcieclk_i2c: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ /* clock-controller@6b */
+ };
+ };
+};
+
+&pcie3 {
+ status = "disabled";
+};
+
+&pcie4 {
+ status = "disabled";
+};
+
+&pcs_mdio3 {
+ status = "okay";
+};
+
+&pcs_mdio4 {
+ status = "okay";
+};
+
+&pcs_mdio5 {
+ status = "okay";
+};
+
+&pcs_mdio6 {
+ status = "okay";
+};
+
+&pcs_mdio11 {
+ status = "okay";
+};
+
+&pcs_mdio12 {
+ status = "okay";
+};
+
+&pcs_mdio13 {
+ status = "okay";
+};
+
+&pcs_mdio14 {
+ status = "okay";
+};
+
+&pcs_mdio15 {
+ status = "okay";
+};
+
+&pcs_mdio16 {
+ status = "okay";
+};
+
+&pcs_mdio17 {
+ status = "okay";
+};
+
+&pcs_mdio18 {
+ status = "okay";
+};
+
+&serdes_1 {
+ status = "okay";
+};
+
+&serdes_2 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2162A-SOM
+//
+// Copyright 2021 Rabeeh Khoury <rabeeh@solid-run.com>
+// Copyright 2023 Josua Mayer <josua@solid-run.com>
+
+&crypto {
+ status = "okay";
+};
+
+&dpmac17 {
+ phy-handle = <ðernet_phy0>;
+ phy-connection-type = "rgmii-id";
+};
+
+&emdio1 {
+ status = "okay";
+
+ ethernet_phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&esdhc1 {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ status = "okay";
+};
+
+&fspi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ /* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
+ spi-rx-bus-width = <8>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ fan-controller@18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ };
+
+ ddr_spd: eeprom@51 {
+ compatible = "st,24c02", "atmel,24c02";
+ reg = <0x51>;
+ read-only;
+ };
+
+ config_eeprom: eeprom@57 {
+ compatible = "st,24c02", "atmel,24c02";
+ reg = <0x57>;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+
+ variable_eeprom: eeprom@54 {
+ compatible = "st,24c2048", "atmel,24c2048";
+ reg = <0x54>;
+ };
+};
Add support for the SolidRun LX2162A System on Module (SoM), and the Clearfog evaluation board. The SoM has few software-controllable features: - AR8035 Ethernet PHY - eMMC - SPI Flash - fan controller - various eeproms The Clearfog evaluation board provides: - microSD connector - USB-A - 2x 10Gbps SFP+ - 2x 25Gbps SFP+ with a retimer - 8x 2.5Gbps RJ45 - 2x mPCI (assembly option / disables 2xRJ45) The 8x RJ45 ports are connected with an 8-port PHY: Marvell 88E2580 supporting up to 5Gbps, while SoC and magnetics are limited to 2.5Gbps. However 2500 speed is untested due to documentation and drivier limitations. To avoid confusion the phy nodes have been explicitly limited to 1000 for now. The PCI nodes are disabled, but explicitly added to mark that this board can have pci. It is expected that the bootloader will patch the status property "okay" and disable 2x RJ45 ports, according to active serdes configuration. Signed-off-by: Josua Mayer <josua@solid-run.com> --- V1 -> V2: reordered "compatible" and "reg" properties V1 -> V2: replaced chip-specific DT node names with generic ones V1 -> V2: removed dead code from fspi node V2 -> V3: dropped deprecated address-cells, address-size props from flash node V3 -> V4: reordered dt properties such that status is last V3 -> V4: changed ethernet-phy on som from /delete-node/ to disabled V5 -> V6: reordered status property in esdhc1 node V5 -> V6: moved i2c2 node by alphabetical order V5 -> V6: added empty lines between led nodes arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/fsl-lx2162a-clearfog.dts | 376 ++++++++++++++++++ .../dts/freescale/fsl-lx2162a-sr-som.dtsi | 73 ++++ 3 files changed, 450 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi